Brizo MultiChoice VETTIS T60088 Quick start guide

91834 Rev. C
MultiChoice®Valve Trim
Installation Instructions
Owners Manual
Write purchased model number here.
Table of Contents:
Warranty ............................................................................... Page 2
Installation Instructions ......................................................... Pages 3 - 6
Maintenance ......................................................................... Page 7
Replacement Parts ............................................................... Page 9
1
You May Need
CAUTION: This system/device must be set by the
installer to ensure safe, maximum temperature.
Any change in the setting may raise the discharge
temperature above the limit considered safe and
may lead to hot water burns.
NOTICE TO INSTALLER: CAUTION!–As the
installer of this valve, it is your responsibility
to properly INSTALL and ADJUST this valve
per the instructions given. This valve does
not automatically adjust for inlet temperature
changes, therefore, someone must make the
necessary temperature knob adjustments at
the time of installation and further adjustments
may be necessary due to seasonal water
temperature change. YOU MUST inform the
owner/user of this requirement by following the
instructions. If you or the owner/user are unsure
how to properly make these adjustments, please
refer to page 7 and if still uncertain, call us at
1-877-345-BRIZO (2749).
After installation and adjustment, you must a󰀩x
your name, company name and the date you
adjusted the temperature knob to the caution label
provided and apply or attach the label to the back
side of the closest cabinet door and the warning
label to the water heater. Leave this Instruction
Sheet for the owner’s/user’s reference.
WARNING: This thermostatic bath valve is
designed to minimize the e󰀨ects of outlet water
temperature changes due to inlet pressure and
temperature changes, commonly caused by
dishwashers, washing machines, toilets and
the like. It may not provide protection from hot
water burns when there is a failure of other
temperature controlling devices elsewhere
in the plumbing system, if the temperature
knob is not properly set or if the hot water
temperature is changed after the settings
are made or if the water inlet changes due to
seasonal changes.
WARNING: Do not install a shut-o󰀨 device on
either outlet of this valve. When this type of
device shuts o󰀨 the water ow, it can defeat
the ability of the valve to balance the hot and
cold water pressures.
For easy installation of your Brizo®faucet you
will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings,care, and
maintenance information.
11/06/2019
1/32" 1/8"
91834
Models
T60088p
T60288p
Series
VETTIS™

91834 Rev. C 2
Cleaning and Care
Care should be given to the cleaning
of this product. Although its nish is
extremely durable, it can be damaged by
harsh abrasives or polish. To clean, simply
wipe gently with a damp cloth and blot dry
with a soft towel.
Parts and Finish
All parts (other than electronic parts and batteries) and nishes of this Brizo® faucet are warranted to the original consumer purchaser
to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet
was rst installed or, for commercial users, the warranty period is ten (10) years for multi-family residential (apartments and condomini-
ums and ve (5) years for all other commercial uses, in each case from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Brizo® faucet are warranted to the original consumer purchaser to be free from
defects in material and workmanship for ve (5) years from the date of purchase or, for commercial users, for one (1) year from the date
of purchase. No warranty is provided on batteries.
What We Will Do
Brizo Kitchen & Bath Company will repair or replace, free of charge, during the applicable warranty period (as described above), any
part or nish that proves defective in material and/or workmanship under normal installation, use and service. If repair or replacement
is not practical, Brizo Kitchen & Bath Company may elect to refund the purchase price in exchange for the return of the product. These
are your exclusive remedies.
What Is Not Covered
Any labor charges incurred by the purchaser to repair, replace, install or remove this product are not covered by this warranty. Brizo
Kitchen & Bath Company shall not be liable for any damage to the product resulting from reasonable wear and tear, outdoor use,
misuse (including use of the product for an unintended application), freezing water, abuse, neglect or improper or incorrectly performed
installation, maintenance or repair, including failure to follow the applicable care and cleaning instructions. Brizo Kitchen & Bath
Company recommends using a professional plumber for all installation and repair of faucets. We also recommend that you use only
genuine Brizo® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts
A warranty claim may be made and replacement parts may be obtained by calling 1-877-345-BRIZO (2749) or by contacting us by mail
or online as follows (please include your model number and date of purchase):
In the United States and Mexico: In Canada:
Brizo Kitchen & Bath Company Masco Canada Limited, Plumbing Group
55 E. 111th Street Technical Service Centre
Indianapolis, IN 46280 350 South Edgeware Road
Attention: Warranty Service St. Thomas, Ontario, Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us www.brizo.com/customer-support/contact-us
Proof of purchase (original sales receipt) from the original purchaser must be made available to Brizo Kitchen & Bath Company for all
warranty claims unless the purchaser has registered the product with Brizo Kitchen & Bath Company. This warranty applies only to
Brizo® faucets installed in the United States of America, Canada and Mexico.
Limitation on Duration of Implied Warranties. Please note that some states/provinces (including Quebec) do not allow limitations on
how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FIT-
NESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY,
WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages. Please note that some states/provinces (including Quebec) do not allow
the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply
to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO
KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (IN-
CLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. BRIZO KITCHEN
& BATH COMPANY SHALL NOT BE LIABLE FOR ANY DAMAGE TO THE FAUCET RESULTING FROM REASONABLE WEAR
AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING
WATER, ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED INSTALLATION, MAINTENANCE OR REPAIR, IN-
CLUDING FAILURE TO FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to residents
of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted
by the laws of the State of New Jersey.
Additional Rights
This warranty gives you special legal rights, and you may also have other rights which vary from state/province to state/province.
This is Brizo Kitchen & Bath Company’s exclusive written warranty and the warranty is not transferable.
If you have any questions or concerns regarding our warranty, please contact us as provided above or visit our website at www.brizo.
com. © 2019 Brizo Kitchen & Bath Company
Limited Warranty on Brizo®Faucets

91834 Rev. C3
B.
1
4
4
2
3
60 Series Installation
1
Cartridge Installation
A.
Turn o󰀨 water supplies. Remove cover (1),
bonnet nut (2), test cap (3) and plasterguard (4).
If screen (5) is in place, remove before installing
cartridge.
Plasterguard may be discarded.
1
2
3
4
Rotate the cartridge (1) so the word “UP” (2)
appears on the top. Insert cartridge into valve
body as shown. Make sure the cartridge tubes
and O-rings (3) are properly seated in holes at
the base of the body. Ensure the keys on the
body are fully engaged with the slots in the
body (4).
For back to back or reverse installations
(hot on right and cold on left): Rotate cartridge
(1) so the word “UP” (2) appears on the bottom.
Install the cartridge making sure that the keys are
fully engaged with the slots in the brass body (see
step B). Slide bonnet nut (3) over the cartridge
and thread onto the body. Hand tighten securely.
Slide bonnet nut (1) over the cartridge and
thread onto the body. Hand tighten securely.
C.
1
5
Back to back Installation
Normal Installation
(changes not required)
Reverse
Installation
Cold
Hot
1
3
2

91834 Rev. C 4
T60088 & T60288 Series Installation
2
Apply plumber tape to threads on brass adapter
(1). Install adapter so that it extends beyond
the nished wall 1-1/4" to 1-1/2". Ensure that
O-Rings (2) are installed properly into grooves
on adapter. For an addtional 1-3/4” of depth,
order extension RP101285.
Slide shower ange (3) over shower arm (4).
Install shower arm (4) onto brass adapter (1),
and secure with set screw (5) on side of shower
arm. Slide ange (3) until it is at against the
nished wall.
Apply plumber tape to threads on shower arm
(4). Thread showerhead (6) onto shower arm.
Do not overtighten showerhead.
Showerhead Installation
(For Tub Spout installation refer to the installation guide provided with your tub spout)
3
Mounting Bracket Installation
Place bracket (1) against nished wall so that the
holes in legs of bracket align with threaded holes
on the rough.
Use two long screws provided to secure the
bracket to the rough. Do not overtighten screws.
Ensure that the bracket lays at against the
nished wall.
6
5
1
4
3
1
2

91834 Rev. C
5
Secure the escutcheon (4) to the bracket (5)
with the 2 screws provided (6).
Do not overtighten escutcheon screws.
Slide screw cover (7) over trim sleeve (3) and
press rmly until the cover is ush with escutcheon.
O-ring will hold screw cover in place.
Before installing volume control handle (8),
ensure valve is in the full cold position (clockwise).
Orient handle so the lever is pointing downward
(6 o’clock position) and press handle onto
cartridge. Secure handle with set screw provided
(9) and press button (10) into hole.
T60088 & T60288 Series Installation
D.
Slide O-ring (1) over cartridge and the bonnet
nut (2). The O-ring, which acts as a spacer to
steady the sleeve, should rest behind the
bonnet nut.
Note: Depending on location of valve within the
wall and wall thickness, an optional extension kit
may be needed. RP91022▲will provide up to
1-3/4" of extension.
Slide the sleeve (3) over the cartridge, body and
O-ring (1). Ensure sleeve is properly positioned
over the front of cartridge.
4
Valve Trim Installation
A.
12
B.
3
1
8
9
10
C.
4
5
6
7
3

91834 Rev. C 6
5
Installation and Adjustment of the Temperature Knob
Failure to do so may cause injury.
Adjust temperature limit stop!
Turn on water supplies; let the water run at
both full hot and full cold to ensure the water
is running as hot/cold as possible. Place a
thermometer in a plastic tumbler, and hold
the tumbler in the water stream. Place the
temperature knob (1) onto the splines (2), then
rotate the temperature knob counter-clockwise
until you achieve your maximum desired
temperature from the outlet (not more than 120°
or the lower temperature mandated by your
local plumbing code).
If max temperature is not achieved before limit
stop (3) on temperature knob (1) meets the
limit stop (4) on the volume control handle.
Remove the temperature control knob (1)
from splines (2). Rotate temperature control
knob (1) clockwise. Place temperature control
knob (1) back onto splines (2) and continue
to rotate counter-clockwise until maximum
desired temperature is achieved.Remove the
temperature knob (1) and replace onto the
splines (2), making sure that the temperature
knob limit stop (3) hits against the volume
handle limit stop (4) as shown. Secure the
temperature knob using screw (5) and place
button (6) in hole.
1
5
6
2
4
2
1
3
T60088 & T60288 Series Installation

91834 Rev. C
7
Cannot receive more than a trickle of water:
Both hot and cold supply lines must be
pressurized. If only one side is pressurized, the
system will not allow adequate ow of water.
Faucet leaks from showerhead: Remove
the showerhead then turn the water on and
o󰀨 to verify if the cartridge is leaking or the
showerhead is draining slowly (the showerhead
may need to be cleaned if water drains slowly).
If leak persists -SHUT OFF WATER SUPPLIES
Replace cartridge assembly - RP47201.
Unable to set or maintain mixed water
temperature:
SHUT OFF WATER SUPPLIES. Remove handle
assembly, trim sleeve, and bonnet nut. Check
to make sure the “H” marking on the cartridge
aligns with the hot inlet and the “C” marking on the
cartridge aligns with the cold inlet to the valve body
The thermostatic cartridge cannot function if hot
and cold inlets are reversed.
Low ow:
Low ow may be caused by clogged screens within
the thermostatic cartridge. To clean the hot and cold
screens in the cartridge, follow the steps below:
1. SHUT OFF WATER SUPPLIES.
2. Remove the handle assembly.
3. Unscrew the hex shaped portion of the cartridge
from the brass section of the cartridge. the brass
section must be held securely by the ats while
the hex is rotated counter-clockwise. Failure to
secure the brass section while rotating the
hex can result in damage to the cartridge.
(See illustration below)
4. Carefully clean any debris from the screens
under running water. If the debris is di󰀩cult to
remove then soak the screens overnight in a
50% water and 50% vinegar solution.
5. Reassemble the cartridge.
6. Replace the handle.
7 Turn the water back on.
8. Reset the limit stop before using the valve.
Cartridge Summary Reference Sheet
Order RP47201 to
Replace Cartridge.
Plastic
Brass
17T
Hex shaped
portion
Flats
60 Series Maintenance

91834 Rev. C 8

91834 Rev. C
Instrucciones para la
Instalación del Accesorio
para Válvulas MultiChoice®
Manual para los Propietarios
Escriba aquí el número del modelo comprado.
Contenido:
Garantía ............................................................................ Página 2
Instrucciones de Instalación ............................................. Páginas 3 - 6
Mantenimiento .................................................................. Página 7
Piezas de Repuesto ......................................................... Página 9
Usted puede necesitar
ADVERTENCIA: El instalador debe apostar
este systema/divisa para garantizar temperatura
maximo y seguro. Cualqueir cambio en el ajuste
puede subir la temperatura del agua de descarga
sobre el límite considerado seguro y puede resultar
en quemaduras de agua caliente.
AVISO PARA EL INSTALADOR: PRECAUCIÓN
– Como instalador de esta válvula, es su
responsabilidad de INSTALAR Y AJUSTAR
apropiadamente esta válvula como se describe
en las instrucciones, por lo tanto, debe
haber una persona para hacer los ajustes
necesarios del pomo para la temperatura en el
momento que se haga la instalación y pueda
necesitar ajustes adicionales por los cambios
estacionales de la temperatura del agua. USTED
DEBE informarle al dueño/usuario sobre este
requisito siguiendo las instrucciones. Si usted
o el dueño/usuario no están seguros como hacer
estos ajustes apropiadamente, por favor reérase
al Página 7 y si todavía no está seguro, llámenos
al 1-877-345-BRIZO (2749).
Después de hacer la instalación y el ajuste,
usted puede agregarle a la etiqueta de aviso
proporcionada, su nombre, el nombre de la
compañía y la fecha cuando ajustó y el pomo para
la temperatura y aplicar o jar la etiqueta al dorso
de la puerta del gabinete más cercano y la etiqueta
de aviso al calentador de agua. Deje la Hoja de
Instrucciones para referencia del dueño/usuario.
ADVERTENCIA: Esta válvula termostática está
diseñada para minimizar los efectos de los
cambios de temperatura de agua por causa
de los cambios de presión y de temperatura
en el agua de entrada, comúnmente causados
por lavadoras de platos, lavadoras de ropa,
inodoros, y otros aparatos por el estilo. Puede
no proporcionar protección de quemaduras de
agua caliente cuando hay alguna falla de otros
aparatos para el control de temperatura en otro
sitio en el sistema de plomería. También no
proporcionará protección si el pomo para el
ajuste de la temperatura no está apropiadamente
jo o si cambia la temperatura del agua caliente
después de hacer los ajustes o si los cambios
del agua de entrada son por los cambios
estacionales.
ADVERTENCIA: No instale un aparato de corte
o cierre en cualquiera de las tomas de esta
válvula. Cuando este tipo de aparato cierra el
ujo de agua, puede hacer fallar la habilidad de
la válvula de balancear las presiones del agua
caliente y fría.
Para instalación fácil de su llave Brizo®
usted necesitará:
• LEER TODAS las instrucciones completamente
antes de empezar
• LEER TODOS los avisos, cuidados,
e información de mantenimiento.
1
11/06/2019
Modelo
T60088p
T60288p
Serie
VETTIS™
1/32" 1/8"

91834 Rev. C
Limpieza y Cuidado de su Llave
Tenga cuidado al ir a limpiar este producto.
Aunque su acabado es sumamente
durable, puede ser afectado por agentes de
limpieza o para pulir abrasivos. Para limpiar
su llave, simplemente frótela con un
trapo húmedo y luego séquela con una
toalla suave.
2
Piezas y Acabado
Todas las piezas (excepto los componentes electrónicos y las pilas) y acabados de esta llave de agua/grifo Brizo® están garantizados
al consumidor comprador original de estar libres de defectos en material y fabricación durante el tiempo que el comprador original sea
propietario de la vivienda en la que la llave de agua fue originalmente instalada o, para usuarios comerciales, el período de garantía
es de diez (10) años para viviendas multifamiliares (apartamentos y condominios y cinco (5) años para todos los demás usos comer-
ciales, en cada caso desde la fecha de compra.
Piezas electrónicas y pilas (si aplicable)
Las piezas electrónicas (excepto las pilas), si las hay, de esta llave de agua/grifo Brizo® están garantizadas al consumidor comprador
original de estar libres de defectos en material y fabricación durante cinco (5) años a partir de la fecha de compra en el caso de los
consumidores comerciales, durante un (1) año a partir de la fecha de compra. No ofrecemos garantía en la pilas.
Lo que haremos
La compañía Brizo Kitchen & Bath Company reparará o reemplazará, sin costo alguno, durante el periodo de garantía aplicable (como
descrito arriba) cualquier pieza o acabado que demuestre estar defectuosa en material y/o mano de obra bajo la instalación, el uso y el
servicio normal. Si la reparación o el reemplazo no es práctico, Brizo Kitchen & Bath Company puede optar por reembolsarle el precio
de compra a cambio de la devolución del producto. Estos son sus remedios exclusivos.
Lo que no está cubierto
Esta garantía no cubre los costos de mano de obra incurridos por el comprador para reparar, reemplazar, instalar o desmontar este
producto. Brizo Kitchen & Bath Company no será
 responsable por cualquier daño al grifo que resulte del desgaste razonable, uso en el
exterior de la propiedad, uso indebido (incluyendo el uso del producto para una aplicación indebida), agua helada, abuso, negligencia,
o instalación, mantenimiento o reparación realizadas incorrectamente, incluyendo el no seguir las instrucciones correspondientes
para el cuidado, la limpieza y el mantenimiento. Brizo Kitchen & Bath Company recomienda que un plomero profesional haga toda la
instalación y las reparaciones. También recomendamos que use solo piezas de repuestos originales Brizo®.
Lo que usted debe hacer para obtener servicio de garantía o piezas de repuesto
Puede hacer un reclamo para la garantía y puede obtener piezas de repuesto llamando al 1-877-345-BRIZO (2749) o contactándonos
por correo o en línea de la siguiente manera (por favor incluya su número de modelo y fecha de compra):
En los Estados Unidos y México: En Canadá
Brizo Kitchen & Bath Company Masco Canada Limited, Plumbing Group
55 E. 111th Street Technical Service Centre
Indianapolis, IN 46280 350 South Edgeware Road
Attention: Warranty Service St. Thomas, Ontario, Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us www.brizo.com/customer-support/contact-us
El comprobante de compra (recibo de venta original) del comprador original debe estar disponible a Brizo Kitchen & Bath Company
para todos los reclamos de garantía a menos que el comprador haya registrado el producto con Brizo Kitchen & Bath Company. Esta
garantía se aplica solo a las llaves de agua Brizo® instaladas en los Estados Unidos de América, Canadá y México.
La limitación de la duración de las garantías implícitas. Favor tome nota de que algunos estados/provincias (incluyendo Quebec) no
permiten limitaciones sobre la duración de una garantía implícita, por lo que es posible que las siguientes limitaciones no le apliquen a
usted. HASTA EL ALCANCE MÁXIMO EN QUE LA LEY APLICABLE LO PERMITA, CUALQUIER GARANTA IMPLCITA, INCLUIDAS
LAS GARANTAS IMPLCITAS DE COMERCIABILIDAD Y DE IDONEIDAD PARA UN PROPSITO PARTICULAR, ESTÁ LIMITADA
AL PERODO LEGAL O A LA DURACIN DE ESTA GARANTA, LO QUE SEA MÁS CORTO.
Limitación de daños especiales, incidentales o consiguientes. Favor tome nota de que algunos estados/provincias (incluyendo
Quebec) no permiten la exclusión o limitación de daños especiales, incidentales o consecuentes, por lo que las limitaciones y ex-
clusiones a continuación puedan no aplicarle. HASTA EL ALCANCE MÁXIMO EN QUE LA LEY APLICABLE LO PERMITA, ESTA
GARANTA NO CUBRE Y BRIZO KITCHEN & BATH COMPANY NO SERÁ RESPONSABLE POR NINGN DAO ESPECIAL, IN-
CIDENTAL O CONSIGUIENTE (INCLUYENDO LOS GASTOS DE MANO DE OBRA PARA REPARAR, REEMPLAZAR, INSTALAR
O DESMONTAR ESTE PRODUCTO), YA SEA RESULTADO DEL INCUMPLIMIENTO DE CUALQUIER GARANTA EXPRESA O
IMPLCITA, INCUMPLIMIENTO DE CONTRATO, AGRAVIO O DE OTRA MANERA. BRIZO KITCHEN & BATH COMPANY NO SE
RESPONSABILIZARÁ POR CUALQUIER DAO AL GRIFO QUE RESULTE DEL DESGASTE RAZONABLE, USO EN EL EXTERIOR
DE LA PROPIEDAD, USO INDEBIDO (INCLUYENDO EL USO DEL PRODUCTO PARA UNA APLICACIN NO INTENCIONADA),
AGUA HELADA, ABUSO, NEGLIGENCIA O INSTALACIN, MANTENIMIENTO O REPARACIN INADECUADA O INCORRECTA,
INCLUYENDO EL NO SEGUIR LAS INSTRUCCIONES CORRESPONDIENTES PARA LA INSTALACIN, EL CUIDADO, Y LA LIMP-
IEZA. Aviso para los residentes del estado de New Jersey: Las disposiciones de este documento tienen la intención de aplicarse en la
máxima medida permitida por las leyes del estado de New Jersey.
Derechos adicionales
Esta garantía le otorga derechos legales especícos, y también puede tener otros derechos que varían de estado/provincia a estado/
provincia.
Esta es la garantía escrita exclusiva de Brizo Kitchen & Bath Company y la garantía no es transferible.
Si tiene preguntas o dudas con respecto a nuestra garantía, por favor comuníquese con nosotros como se indica arriba o visite nuestro
sitio web www.brizo.com. © 2019 Brizo Kitchen & Bath Company
Garantía en los grifos Brizo®