Broadata LBC-H-R-DOP User manual

LBC-H-R-DOP
LINK BRIDGETM HDBASET
HDMI RECEIVER
WITH DUAL VIDEO OUTPUT
BCI reserves the right to make changes to the products described herein without prior
notice or consent. No liability is assumed as a result of their use or application. All
rightsreserved.
©2015 Broadata Communications, Inc.

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [email protected] 3
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASEOBSERVETHEFOLLOWINGSAFETY
PRECAUTIONS
SURGEPROTECTION DEVICERECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [phone]
4
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION .............................................5
2.0 OPERATION CONTROLS AND FUNCTIONS ...............6
2.1 FRONT PANEL .................................................................6
2.2 REAR PANEL ...................................................................7
3.0 SERIAL CONTROL ..........................................................8
3.1 D-SUB PIN ASSIGNMENT ...............................................8
3.2 IR BLASTER CABLE PIN ASSIGNMENT........................9
3.3 IR RECEIVER CABLE PIN ASSIGNMENT ......................9
4.0 MAINTENANCE AND TROUBLESHOOTING ...............10
4.1 MAINTENANCE ..............................................................10
4.2 TROUBLESHOOTING ...................................................10
5.0 SPECIFICATIONS...........................................................12
6.0 SERVICE PROCEDURE ................................................13
6.1 REPLACEMENT POLICY ..............................................13
6.2 RETURN AND REPAIR SERVICE .................................13
7.0 LIMITED WARRANTY ....................................................14

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [email protected] 5
1.0 PRODUCT DESCRIPTION
TheLBC-H-R-DOPreceiveraccepts from the transmitterunitthesignal
ofresolutionsupto1080p Full HD, 4Kx2Ktiming,3Dandmulti-channel
digitalaudioformatsand sends to twoHDTVoutputs.The HDMI can be
connectedtoHDMIdisplayfor instantnearbydisplayandthe CAT-5e/6/7
can be connected to CAT5e/6/7 to HDMI transmitter for a distance of
up to 100 meters with Bidirectional PoC feature. Further, a total of
100Mbps Ethernet transmission rate allows all connected devices to
share the Ethernet service and Bi-directional PoC provides PoC to the
transmitter, or received from compatible PoC transmitter through
CAT-5e/6/7.
Features
• Extend HDMI Signals up to 100 meters Over One CAT-5e/6
Cable with dual video output
•SupportsFullHDTVVideoResolutionsup to 4K2K@30Hz
•Fully Uncompressed Video &Audio Provides Zero Loss of
Quality
•SupportsTrueDDC/EDID/HDCPTransmission
•Video/Audio+IR+Data+Ethernet, Over 1 CAT-5e/6 Cable
•Two-way 24V/POC Remoting Power
•HDMI 1.4 and HDCP 2.2 compliant
•Supports both RS232 and IR Control Data

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [phone]
6
2.0 OPERATION CONTROLS AND FUNCTIONS
2.1 Front Panel
1. HDMI OUT 1 & 2: Connect to HDMI displays for instant image
display or cascade with another family type transmitter. The
unit will detect HDMI OUT 1’s EDID when it obtain a 4Kx2K
EDIDandsendoutthe signal accordingly to otheroutputports.
If HDMI OUT 1’s EDID is without a 4Kx2K’s EDID the unit will
detect all output’s EDID and send out the signal that all output
can accept.
This device obtains the last memory function therefore, the
devicewillusethe last HDMIOUT1’sEDID when HDMIOUT
1 is not connected to a display after power cycling or switch
in between the EDID setting.
2. LAN: Connect to intranet or internet service system for a total
sharing rate of 100Mbps within the link of Receiver.
Warning: DO NOT connect this slot with any of the
CAT-5e/6/7 port, doing so may trigger a power shot down
and ruin the device.
3. RS-232 OUT: Connect to a RS-232 enabled device (with
supplied 3.5mm Phone Jack to D-Sub 9-Pin male adaptor) for
transmit of RS-232 commands.
HDMI OUT 1 HDMI OUT 2
LAN RS-232 OUT
CAT5e/6/7 to HDMI with LAN/IR/RS-232 Receiver
123
1

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [email protected] 7
2.2 Rear Panel
1. POWER LED: Once the power supply is connected the LED
willilluminate.
2. DC 24V: Plug the24VDCpowersupplyintothe unitandconnect
the adaptor to an AC outlet.
3. IR 2 BLASTER: ConnecttothesuppliedIR Blaster cable forIR
signaltransmission.Place theIRBlasterin directline-of-sightof
the equipment to be controlled.
4. IR 1 EXTENDER: Connect to the supplied IR Extender cable
forIRsignal reception.Ensurethat remotecontrollerbeing used
is within the direct line-of- sight of the IR Extender.
5. USB: This port is reserved for firmware update only.
6. LINKLED: ThelinkLEDwillilluminatewhenboththeinputsource
and output display signals are connected through CAT cable.
When it blinks regularly it states the display is NOT sending
signalstoReceiverbut theTransmitterandReceiverarelinked
and if it blink irregularly it states an error has occurred.
7. CAT-5e/6/7 IN: Connect this port to HDMI to CAT-5e/6/7
Transmitter(withor withoutPoCfunction) withCAT-5e/6/7cable
to extend the signal up to 100m.
POWER
DC 24V
CAT5e/6/7 IN
IR 2
BLASTER
USB
LINK
IR 1
EXTENDER
12
34567

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [phone]
8
3.0 SERIAL CONTROL
3.1 D-Sub PinAssignment
Pin
1
2
3
4
5
6
7
8
9
Define TX/RX
N/C
TxD/RxD
RxD/TxD
N/C
GND
N/C
N/C
N/C
N/C

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [email protected] 9
3.2 IR Blaster Cable PinAssignment
3.3 IR Receiver Cable PinAssignment
IR Blaster Power 5V
IR Blaster Signal
NC
IR Receiver
IR Signal
Power 5V
Grounding

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [phone]
10
4.0 MAINTENANCE AND TROUBLESHOOTING
4.1 Maintenance
Thereisnooperatormaintenanceother then keeping the units
clean. However,observethefollowinglightindicatorsto make
sure that the unit is working properly:
4.2 Troubleshooting
If the LBC-H-R-DOP units do not operate properly after
installation,checkfor possiblecablebreaks, looseconnections,
and incorrect cable connections. If problems persist that may
be fiber related, contact BCI at 1-800-214-0222 for further
assistance.
For electrical problems, perform the following troubleshooting
procedures:
1. If the POWER indicator is OFF, check for the following:
a. The line cord is plugged into the unit and your outlet
haspower.
2. If the POWER indicator is ON, but the Link indicator is
OFF, check for the following:
a. Makesuretheappropriatecablesarebeingused.
b. Cableandcableconnectorsarenotbroken.
c. For each unit, the transmit (TX) cable is connected to
theotherunit’sreceiver (RX).
3. If the POWER indicator and Link indicator are ON, but
the channels are not operating, then:
a. Checktoseethatthe attacheduserequipmentisturned
on.
b. Both ends of the link are connected to the
corresponding equipment and to the same
correspondingchannelport.

LBC-H-R-DOPUserManual
LinkBridgeTM HDBaseTHDMIReceiverw/DualVideoOutput
Broadata Technical Support, [email protected] 11
c. Cable connections at both channels are securely
fastened to each connector. Turn the power off, then
back on to reset the link.