Broadata LBH-H/O-EAD-R-ICP User manual

LBH-H/O-EAD-R-ICP
LINK BRIDGETM HBASET/HDMI
RECEIVER SYSTEM WITH EXTERNAL AUDIO
AND INLINE CONTROL PROCESSOR
BCI reserves the right to make changes to the products described herein without prior
notice or consent. No liability is assumed as a result of their use or application. All
rightsreserved.
©2015 Broadata Communications, Inc.

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [email protected] 3
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASE OBSERVE THE FOLLOWING SAFETY
PRECAUTIONS
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [phone]
4
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION ..............................................5
2.0 OPERATION CONTROL AND FUNCTIONS ...................6
2.1 RECEIVER EXTENDER FRONT AND REAR PANEL.....6
2.2 ICP FRONT AND REAR PANEL .....................................7
3.0 CONNECTOR PINOUT ASSIGNMENT ...........................8
3.1 EXTENDER ......................................................................8
3.1.1 SERIAL DATA INTERFACE............................................8
3.1.2 STATUS LEDS ...............................................................9
3.2 ICP .................................................................................10
3.3 LB-KP8 ...........................................................................11
4.0 LB-ICP WEB SERVER DESCRIPTION .........................13
5.0 SPECIFICATIONS...........................................................39
6.0 SERVICE PROCEDURE ................................................42
6.1 REPLACEMENT POLICY ..............................................42
6.2 RETURN AND REPAIR SERVICE .................................42
7.0 LIMITED WARRANTY ....................................................43

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [email protected] 5
1.0 PRODUCT DESCRIPTION
Overall
•A selectable HDBT or HDMI receiver with multiple control I/O
ports
•Provides in-line control I/O paths
Receiver
•Receive HDMI, audio, IR, and RS-232 up to 100 meters over 1
CAT-5e/6 cable
•Supports video resolutions up to 1080p 60Hz and
1920 x 1200@60Hz, as well as 4K@30Hz
•Supports HDMI w/embedded audio extraction
•EDID pass-through support, automatically detects the factory
setting of the connected display
Control
•Control I/O ports contain:
- two (2) RS-232
- two (2) Relay
- two (2) Digital I/O
- one (1) IR
- one (1) Ethernet
•Control and monitorAV devices using a standard Ethernet
network (Smart phone or PC) or RS-232 (keypad)
•Front panel port status indicators
•Userfriendlycustomizable controlconfigurationsvia built-in
web server
ORDERING INFORMATION
LBH-H/O-EAD-R-M-SC-ICP LinkBridgeHDBT/HDMI Receiver
w/Control I/O Ports

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [phone]
6
2.0 OPERATION CONTROLSAND FUNCTIONS
2.1 Receiver Extender Front and Rear Panel
1. Power/Link: The red LED indicates the unit is powered up.
The green LED indicates that the unit has a good HDBT
connection.
112
In
12
11
RS232
2
2
Out
2
2
1
I / O
IR
REM
2
1
+5V In C NC NO
NC NO
C
Out
AUXRELAY
InIn
11
2
Out
2
DATA
1
2
1
2
DATA DATA
IR
LBH-H/O-EAD-RX-ICP
PWR/ LINK
L / RSPDIF
AUDIO
HDMI IN
HDMI
5
OPT
HDMI OUT
AUTO
1
Front
RESET
Out In
IR
CONFIG
SW
ON
11
LAN
+24VDC
1.25 A
LINK
Rear
ICP Extender
ICP
Extender
112
In
12
11
RS232
2
2
Out
2
2
1
I / O
IR
REM
2
1
+5V In C NC NO
NC
NO
C
Out
AUXRELAY
InIn
11
2
Out
2
DATA
1
2
1
2
DATA DATA
IR
LBH-H/O-EAD-RX-ICP
PWR/ LINK
L / RSPDIF
AUDIO
HDMI IN
HDMI
5
OPT
HDMI OUT
AUTO
1
Front
RESET
Out In
IR
CONFIG
SW
ON
11
LAN
+24VDC
1.25 A
LINK
Rear
10
1
23
4
56
7
89
HDCP
SPDIF
L/R
11
EDID
Loc
Rem
12 13
14 15

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [email protected] 7
2. HDCP LED: The blue LED is lighted when HDCP video is
present.TheblueLEDblinks whennon-HDCPvideo ispresent.
3. SPDIFLED:LightedwhencorrespondingSPDIFaudiois active.
4. DATALEDs: Lightedwhencorrespondinginputoroutputports
are active.
5. L/R LED: Lighted when corresponding audio is active.
6. DATA: RS-232 pass-through data connector.
7. IR: IR pass-through IR connector.
8. SPDIF: SPDIF audio output connector.
9. L/R: L/R audio output connector.
10. HDMI IN: HDMI video input connector.
11. HDMI OUT: HDMI video output connector.
12. EDID Selection: Select Local or Remote EDID (for HDMI IN)
13. Input Video Selection: Reserved.
14. HDBT: HDBT CAT-5e/6/7 cable connector.
2.2 ICP Front and Rear Panel
1. Digital I/O: Digital input/output ports.
2. DigitalI/O LEDs:Lightwhen thecorresponding portsare active
high.
112
In
12
11
RS232
2
2
Out
2
2
1
I / O
IR
REM
2
1
+5V In C NC NO
NC
NO
C
Out
AUXRELAY
InIn
11
2
Out
2
DATA
1
2
1
2
DATA DATA
IR
LBH-H/O-EAD-RX-ICP
PWR/ LINK
L / RSPDIF
AUDIO
HDMI IN
HDMI
5
OPT
HDMI OUT
AUTO
1
ICP Front
RESET
Out In
IR
CONFIG
SW
ON
11
LAN
+24VDC
1.25 A
LINK
ICP Rear
10
12
34
56
7
89
HDCP
SPDIF
L/R
11
EDID
Loc
Rem
12
13
14 15 16 17

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [phone]
8
3. RS-232: Serial port to control devices.
4. RS-232 LEDs: Light when the corresponding RS-232 ports
are active.
5. REM LED: Light when the unit is set as a remote unit.
6. IR LED: Light when the IR out are active.
7. RELAYLED: Light whenthecorresponding,normallyopen pins,
are closed.
8. RELAY: Normally open and normally closed relay ports.
9. AUX-In and AUX-Out: Reserved.
10. DC24V: DC power input connector.
11. IR Out: IR blaster port.
12. SW: The unit configuration dip switch
13. IR Learner: Built-in IR receiver for IR learning.
14. IR Learner LED: Lighted when the unit is IR learning mode.
15. CONFIG: Configuration/keypad port
16. LAN: Ethernetconnector.
17. RESET: Press the button to reset the device back to factory
default settings.
3.0 CONNECTOR PINOUT ASSIGNMENT
3.1 Extender
3.1.1 Serial Data Interface
Each LBH-H/O-EAD-R-ICP unit can be used for RS-232 and
IR interface.
RS-232/ IR Data
The LBH-H/O-EAD-R-ICP transmits two channels of data
signals. Follow the procedures for installing data terminal
devices.
1. Label and connect one serial data cable to the user’s
RS-232 or IR device.

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [email protected] 9
2. Connect the other end of this cable to the front panel
data terminal block connector on the
LBH-H/O-EAD-R-ICP (see below).
3.1.2 Status LED’s
Additional status LED’s are provided for the user to indicate
the presence of HDCP video, audio presence and data
presence. These are to assist the user in identifying right from
thefrontpanelwhetheragivensignalispresentfortransmission
andaidinthetroubleshootingprocessifagiven signalis missing.
RS-232/IR Terminal block pinout
HDCP LED: Will be solid LED when video
input has a HDCP. It will blink when video
input does not have HDCP.
Data in and Data out LED:
It will be on when the unit
detects data signal.
SPDIF & L/R detect LED.
It will be on when the unit detect
the audio input signal.
112
In
12
11
RS232
2
2
Out
2
2
1
I / O
IR
REM
2
1
+5V
In
C
NC NO
NC
NO
C
Out
AUXRELAY
InIn
11
2
Out
2
DATA
1
2
1
2
DATADATA
IR
LBH-H/O-EAD-RX-ICP
PWR/ LINK
L / RSPDIF
AUDIO
HDMI IN
HDMI
5
OPT
HDMI OUT
AUTO
1
HDCP
SPDIF
L/R
EDID
Loc
Rem

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [phone]
10
3.2 LB-ICP
Front
Digital I/O CH-1 GND Digital I/O CH-2 GND GND
Relay 1 Normally Open Relay 1 Common Relay 1 Normally Closed Reserved/Do Not Connect Reserved/Do Not Connect
Digital I/O LEDs 1=I/O Ch-1 2=I/O Ch-2
Remote LED (On=Remote) IR TX LED
(On=IR TX Act.)
}
On=High Level
Reserved/Do Not Connect Reserved/Do Not Connect
Relay 2 Normally Closed
Relay 2 Common
Relay 2 Normally Open
RS-232 OUT CH-2 RS-232 OUT CH-1
GND
RS-232 IN CH-2 RS-232 IN CH-1
1=Relay 1 ON 2=Relay 2 ON
RS-232 LEDs
1=CH-1 Activity 2=CH-2 Activity

LBH-H/O-EAD-R-ICPUserManual
Link BridgeTM HBaseT/HDMI Receiver System w/ExternalAudio and Inline Control Processor
Broadata Technical Support, [email protected] 11
3.3 LB-KP8/LB-KP4
Rear
IR OUT for
external emitter IR detector
behind holes
Reset button:
push to reset to
default settings
RJ-45
1 - TX+
2 - TX-
3 - RX+
4 - N/C
5 - N/C
6 - RX-
7 - N/C
8 - N/C
CONFIG/Keypad
1. +12V keypad power
2. RS-232 IN
3. RS-232 OUT
4. GND
IR Learn LED
(ON in IR
Learn mode
DIP SW
Position 1: Local/Remote
(Local=OFF)
Position 2: Reserved
Position 3: Reserved
Position 4: Reserved
Rear
Control RJ-45
Pin 1: RS-232 OUT
Pin 2: RS-232 IN
Pin 3: --no connect--
Pin 4: +12v
Pin 5: +12v
Pin 6: --no connect--
Pin 7: GND
Pin 8: GND