TechniSat DigiPal1 User manual

Operating Manual
DigiPal 1
Receiver for
DVB-T programmes
Art.-No. 0000 4903
EE
EEPP PPGG GG
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 1

1 Contents
1 Contents . . . . . . . . . . . . . . . . . . .2, 5
2 Illustrations . . . . . . . . . . . . . . . . . . .3
3 Please read this first . . . . . . . . . . .6
Safety notices! . . . . . . . . . . . . . . . .7
Initial installation . . . . . . . . . . . . . .8
4 Connections . . . . . . . . . . . . . . . . .10
4.1 Power mains connection . . . . . . . . . . . . . .11
4.2 Antenna connection . . . . . . . . . . . . . . . . . .11
4.3 Connection to a television set . . . . . . . . . .11
4.4 Tuning the UHF channel . . . . . . . . . . . . . .12
4.5 Adjusting the antenna . . . . . . . . . . . . . . . .13
4.6 Serial interface . . . . . . . . . . . . . . . . . . . . . .13
5 Installation . . . . . . . . . . . . . . . . . .14
5.1 OSD - language selection . . . . . . . . . . . . .14
5.2 Basic settings . . . . . . . . . . . . . . . . . . . . . . .14
5.2.1 Parental control . . . . . . . . . . . . . . . . . . . . .15
5.2.2/3 Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
5.3 Audio and Video settings . . . . . . . . . . . . . .15
5.3.1 Image format . . . . . . . . . . . . . . . . . . . . . . .16
5.3.2 Language . . . . . . . . . . . . . . . . . . . . . . . . . .16
5.3.3 SCART mode . . . . . . . . . . . . . . . . . . . . . . .16
5.3.4 Video system . . . . . . . . . . . . . . . . . . . . . . .16
5.3.5 UHF output channel . . . . . . . . . . . . . . . . . .16
6 Operation . . . . . . . . . . . . . . . . . . . .16
6.1 Switching on and off . . . . . . . . . . . . . . . . .17
6.2 Programme selection . . . . . . . . . . . . . . . . .17
6.3 Volume adjustment . . . . . . . . . . . . . . . . . .18
6.4 Selecting a different language . . . . . . . . . .19
6.5 TV/Radio switching . . . . . . . . . . . . . . . . . .19
6.6 Return to previous programme selected . .19
6.7 Display time and programme info. . . . . . . .20
6.8 Additional programme information . . . . . . .20
6.9 Transponder information . . . . . . . . . . . . . .20
6.10 Videotext . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.11 Electronic Programme Guide . . .21
6.11.1 Display Electronic Programme guide . . . . .21
6.11.2 Programme preview following days . . . . . .21
6.11.3 EPG information . . . . . . . . . . . . . . . . . . . . .22
6.11.4 Exiting from EPG . . . . . . . . . . . . . . . . . . . .22
2
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 2

6.12 Timer . . . . . . . . . . . . . . . . . . . . . . .22
6.12.1 Programming by EPG . . . . . . . . . . . . . . . .22
6.12.2 Manual Programming . . . . . . . . . . . . . . . . .23
7 Changing basic programming . . . .25
7.1 Configuring the programme list . . . . . . . . .25
7.1.1 Calling up the programme list . . . . . . . . . .25
7.1.2 Adding programmes to programme list . . .25
7.1.3 Deleting programmes . . . . . . . . . . . . . . . . .26
7.1.3.1 Deleting from the Favourites list . . . . . . . .26
7.1.3.2 Deleting from the Total list . . . . . . . . . . . . .26
7.1.4 Sorting programmes . . . . . . . . . . . . . . . . .27
7.1.5 Blocking programmes (parental control) . .28
7.2 Changing the PIN . . . . . . . . . . . . . . . . . . .28
7.3 Lifting programme block . . . . . . . . . . . . . .29
7.4 Programme search . . . . . . . . . . . . . . . . . .29
7.4.1 Automatic search/scan . . . . . . . . . . . . . . . .29
7.4.2 Expanded search function.. . . . . . . . . . . . .30
7.4.3 Manual search . . . . . . . . . . . . . . . . . . . . . .30
7.4.4 After a scan . . . . . . . . . . . . . . . . . . . . . . . .31
7.5 Calling up default setting/delete all . . . . . .32
7.5.1 Activating default setting . . . . . . . . . . . . . .32
7.5.2 Delete all programmes . . . . . . . . . . . . . . . .32
7.6 System configuration . . . . . . . . . . . . . . . . .33
8 Technical Terms . . . . . . . . . . . . . .33
9 Technical Data . . . . . . . . . . . . . . .34
10 Trouble-shooting guide . . . . . . . . .36
5
Your receiver carries the CE mark and complies
with all relevant EU specifications.
Not liable for printing errors, alterations may be effected without notice.
Current as per 10/02
Copying and reproduction subject to permission by the publisher.
TechniSat and DigiPal 1 are registered trademarks of
TechniSat Digital GmbH
P.O. Box 560
D-54541 Daun
Germany
www. technisat.de
_02
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 3

On/stand-by
Numeric keypad
Programme list on/off
Back
Menu on/off
Sound on/off
Language selection
Programme down
Multi-function keys
Volume +
Programme up
TV/Radio operation
EPG
OK
Volume -
Arrow key right
Arrow key left
Arrow key up
Arrow key down
Remote control
Info key
2 Illustrations
3
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 4

4
DC input
RS 232
interface
Antenna
output
Input terrestrial aerial
(antenna feed +5V/100mA/
switchable via OSD)
LED display
Programme selection
up/down
SCART socket TV
On/Standby
Front view
Rear view
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 5

6
3 Please read this first
> Before you start operating the receiver, please check
that all necessary parts have been delivered.
You should have the following:
1 receiver, 1 mains plug/adapter, 1 remote control, 1
operating manual, 1 guarantee card, 2 batteries (1,5V
micro-cells).
> Insert the batteries supplied in the battery compart-
ment of the remote control unit, taking care to observe
the indicated polarity.
> Before connecting the receiver, please first read the
safety precautions in Chapter 3.
>Chapters 4 and 5 describe connecting the
receiver, and adjusting it to the antenna and the
television set.
>Chapter 6 describes all the functions required for
everyday use, such as programme selection or
volume adjustment.
> In Chapter 7 you will find information on how to add
new programmes, or how to change the order of
programmes in the list.
> Technical terms used in the operating manual are
explained in Chapter 8.
> Technical data may be found in Chapter 9.
> A trouble-shooting guide to help you find and correct
faults can be found in Chapter 10.
Disposal instructions
The packaging materials used for this unit consist entirely of
recyclable materials. Please ensure that they are disposed of
appropiately, e.g. via the “Dual System” in Germany.
Please note that spent batteries such as those used in the
remote control, as well as any electronic parts, should not be
disposed of in your regular domestic refuse. They should be
disposed of separately, either via your ratailer, or through the
local authorities.
Disconnecting the unit
The unit should be disconnected from the mains power
supply during electrical storms, or when the unit is not in use
for an extended period of time.
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 6

Safety precautions
For your own protection you should read the safety
precautions carefully before operating your new receiver.
The manufacturer accepts no liability for damage caused by
inappropriate handling, or by non-compliance with the safety
precautions.
> In order to ensure adequate air circulation, place the
unit on a smooth, flat surface, and do not place any
articles on the top of the unit. Air slots designed to
assist circulation, and to allow heat to dissipate from
the unit, are located here.
> Do not place any burning objects, such as lighted
candles, on top of the unit.
> Do not expose the unit to water in drop or spray form,
and do not place any liquid-filled objects, such as
vases, on top of the unit.
> The unit should be operated only in a temperate clima-
te.
> Under no circumstances should you open the unit! You
are in danger of receiving an electric shock. If it is
necessary to open the unit, this should only be carried
out by qualified persons.
In the following cases you should disconnect the unit from the
mains power and call a repair specialist:
> the power switch or the cable are damaged
> the unit has been exposed to humidity, or liquid has
entered the unit
> in case of considerable malfunction
> in case of severe external damage
7
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 7

Important notes on operation
The use of so-called "On Screen Displays" (see example)
simplifies the operation of the receiver, and reduces the num-
ber of keys required on the remote control. All functions are
indicated on the TV screen, and can be adjusted with a few
key-strokes. Groups of functions that belong together are pla-
ced in “MENUES”.
The function selected will be highlighted in a different colour.
The function keys red, yellow, green and blue are depicted by
coloured bars in the bottom line. These colour bars represent
different functions in the various menues, which can be initia-
ted by pressing the appropriate coloured keys (multi-function
keys) on the remote control. The function keys are only active
when a brief description is shown in the appropriate field.
Help function:
Wherever it is available in a menu, pressing the blue
function key will display a help text, pressing again will end
the display.
Key descriptions and terms used in the OSD menu are
printed in bold type in this operating manual.
For example:
> Use the Menu key to call up the Main Menu.
(Fig.
3-1)
> Now select the line OSD-Sprache Language by
using the arrow keys up down to highlight the
appropriate line.
> Confirm by pressing OK.
> You can exit from the menu either by pressing the
Menu okey or by repeatedly pressing the key Back.
Initial installation
Once you have read the safety precautions, connect the unit
as described in Chapter 4. Then switch on the unit as descri-
bed in Chapter 6. When switching on the receiver for the first
time the installation window will be displayed
(Fig. 3-2). In
order to adjust the most important settings of the receiver,
simply follow the instructions.
8
(Fig. 3-1)
(Fig. 3-2)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 8

> Press the OK key to display the selection window for
the OSD language.
(Fig. 3-3)
> Use the arrow keys up down to mark the required
language.
> Confirm with OK, in order to advance to the selection
of the preferred audio language.
(Fig. 3-4)
> Use the arrow keys up down to select the prefer-
red audio language.
> Confirm with OK, to confirm the selection, and to pro-
ceed to the selection of the time zone.
(Fig. 3-5)
> Use the arrow keys up down to select the time
zone corresponding to your location.
> Confirm b y pressing OK to confirm your selection,
and to proceed to the channel search function.
(Fig. 3-
6)
> Please note the message displayed (Fig. 3-7) and
commence the search by pressing OK.
An automatic programme scan will now commence,
covering the entire input frequency range of the recei-
ver. This process may take several minutes.
> Your box is ready for operation when the search is
completed.
> Press the OK key to complete the initial installation
and to switch to normal operation.
9
(Fig. 3-3)
(Fig. 3-4)
(Fig. 3-5)
(Fig. 3-6)
(Fig. 3-7)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 9

10
Connection to a TV set by means of a Scart
cable:
a. Connection from antenna to the terrestrial antenna
input of the DVB-T receiver.
b. Mains power connection
c. Scart connection from the DVB-T receiver to the television
set.
Connection to the TV set by means of an antenna
cable
:
a. Connection from the antenna to the terrestrial anten-
na input of the DVB-T receiver.
b. Mains power connection
d. Connection from the antenna output to the antenna
input of the television set.
Connecting the DVB receiver
a
b
c
d
a
b
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 10

11
4 Connections
The references a b c etc. stated below refer to the
illustration on page 10.
4.1 Mains power connection
The receiver should only be connected to the mains power
supply when the unit has been completely connected with all
other relevant components. This will eliminate the danger of
damage to the receiver or other components.
bWhen you have effected all the connections, use the
power connection switch supplied to connect the
receiver with a 230V/50 Hz power supply.
4.2 Connection to the antenna
aThe cable coming from the terrestrial antenna must be
connected to the terrestrial antenna input of the
receiver.
Where possible you should use a roof-mounted anten-
na. A room antenna may be sufficient where reception
conditions are particularly favourable. When using an
active antenna be sure to switch on the antenna feed
(Point 5.2).
4.3 Connection to a television set
Once you have connected your receiver to the television set
as described above, it may be necessary, before you can
make further settings or adjustments, to adapt the receiver to
the TV standard of your TV set.
Please note Point 5.3 (Video system).
4.3.1 Via SCART cable:
Using a SCART cable connection between the receiver and
the TV set will ensure optimum image quality.
cConnect the receiver (SCART socket TV) and the
TV set (SCART socket) via a SCART cable. If your TV
set is appropriately equipped, it will switch automati-
cally to AV mode, and thus to DVB-T mode, when the
receiver is switched on.
4.3.2 Via HF cable:
If your TV set is not equipped with a SCART socket, you will
have to connect the receiver to the antenna input socket of
the TV set.
If this type of connection is used, sound reproduction will be
in mono only.
dConnect the receiver (Antenna output) to the
antenna input socket of your TV set by means of a
suitable TV connection cable.
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 11

You must now tune your TV set to the transmission channel
of the receiver. Select a free programme slot on your TV set
and tune it to channel 41 (refer to operating manual of the TV
set if necessary).
If you do not receive a clear image on channel 41, this may
be the result of a neighbouring channel being set to a pro-
gramme being received from the same antenna. You can
check on this by temporarily removing the antenna cable from
the Input terrestrial antenna socket of the receiver. If
you then temporarily receive a clear image, you should select
another transmission channel for the receiver in the range of
21 to 69.
4.4 Setting the UHF output channel
Proceed as follows:
> Press the Menu key to display the Main Menu. (Fig.
4-1)
> Now select the line Settings, using the arrow keys
up down to mark the appropriate line.
> Confirm by pressing OK.
The sub-menu Settings will be displayed.
(Fig. 4-2)
> Now use the arrow keys up down to highlight the
line Audio Video Settings.
> Confirm by pressing OK.
The sub-menu Audio Video Settings will now be
displayed.
(Fig. 4-3)
> Now, use the arrow keys up down in order to hig-
hlight the blue field, thus selecting the menu line UHF
output channel.
> Now tune your TV set to a free UHF channel in the
range of 21 to 69.
> Then set the new output channel of the receiver by
means of the arrow keys right left.
The receiver will now transmit on the UHF channel
shown on the display.
12
(Fig. 4-1)
(Fig. 4-2)
(Fig. 4-3)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 12

Your receiver will now check automatically whether the
channel you have selected, as well as the lower neig-
hbouring channel adjoining it, are free (Fig. 4-4). If the
channel is already occupied, a note to this effect will
be displayed
(Fig. 4-5). In this case, please repeat the
procedure until you find a suitable free channel.
> When you have found the optimum UHF channel,
please remember to store this in your TV set memory.
You can now make further adjustments in the menu
Audio Video Settings,or you can press the Menu
key to return to normal operation. This setting will be
automatically stored when you exit the menu.
> If your television set is equipped only with an automa-
tic search function, then simply set any UHF channel
on your receiver, then start the automatic search pro-
cedure of your television set. If necessary, keep
repeating this procedure until you have found a suita-
ble output channel, then store this in your TV set
memory.
> At this stage it may be necessary to fine-tune the
channel on your TV set.
4.5 Adjusting the antenna
Your receiver is equipped with a signal strength indicator to
facilitate the optimum adjustment of the antenna.
> Press the Menu key to call up the Main Menu.
> Now use the arrow keys up down to select the
menu line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
(Fig. 4-6).
> Now use the arrow keys up down to select the
menu line Antenna adjustment.
> Confirm by pressing OK. The menu Antenna
adjustment will be displayed
(Fig. 4-7)
> Now use the arrow keys left right to select the
channel with the weakest reception signal strength.
> Now adjust the position of the antenna until both bar
indicators show optimum signal strength.
red bar poor reception
yellow bar good reception
green bar very good reception
4.6 Serial interface RS 232
The RS 232 interface serves to carry out updates of the ope-
rating software, as well as to facilitate pre-programming via a
PC.
13
90
70
(Fig. 4-4)
(Fig. 4-5)
(Fig. 4-6)
(Fig. 4-7)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 13

14
5 Installation
Now that you have connected your receiver, and commenced
operation, you can turn to optimising the setting for your
personal preferences.
5.1 OSD Language
This menu item gives you the option of selecting the menu
language of your choice.
In order to change the OSD language, proceed as follows:
> Press the Menu key to call up the Main Menu.
(Fig.
5-1)
> Use the keys arrow keys up down to select the
menu line OSD Language.
> Confirm by pressing OK.
The sub-menu OSD Language will be displayed.
> Use the arrow keys up down to select the desired
language.
> Store the selection in memory by pressing OK.
> Press the Back key to return to the Main Menu.
5.2 Basic settings
In order to operate your DVB receiver as conveniently as
possible, you should make some adjustments to
accommodate your personal preferences.
> Press the Menu key to call up the Main Menu.
> Use the arrow keys up down to select the line
Settings.
> Confirm by pressing OK.
The menu Settings will be displayed
(Fig. 5-2)
> Use the arrow keys up down to select the line
Basic Settings.
> Confirm by pressing OK.
The menu Basic Settings will be displayed
(Fig. 5-
3).
> Use the arrow keys up down to move around
within the menu, and to change the individual
positions as indicated. When selecting a menu item
please also note notices displayed on screen, where
applicable.
The following settings can be made:
(Fig. 5-1)
(Fig. 5-2)
(Fig. 5-3)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 14

5.2.1 Parental control
Your receiver is equipped with a parental control function.
Programmes that you have blocked in line with Points
7.1.5 and 7.2 can only be viewed after a four-digit PIN code
has been entered. Go to this line and press the OK key to
activate or deactivate the parental control function on resp.
off.
5.2.2 Time difference to GMT (hours)
Your receiver is equipped with a clock. This is synchronised
via the signal received with Greenwich Mean Time. If you
have entered None (see 5.2.3) under Country, then you
must simply correct the current time with regard to your local
time, using the arrow keys left right or the OK key. For
Germany, this difference is +1 hour in winter, +2 hours in
summer.
5.2.3 Country
This function automatically provides for the switch to Daylight
Savings Time in summer, and back in winter. Use the arrow
keys left right to enter your location in the line Country.
> Press the Back key to return to the Settings menu,
or press the Menu key to return to normal operation.
The settings will be automatically stored in memory.
5.2.4 Antenna feed 5V
If you are using an active antenna, you will have to switch on
the antenna feed (5V/100mA). The antenna will be supplied
via the Terrestrial antenna input.
> Use the arrow keys left right in this line to switch
the antenna feed on or off.
In case of overload, or if there is a short circuit in the antenna
feed, this will be switched off automatically. If this occurs,
please repair the fault, then switch on the antenna feed
again.
5.3 Audio/Video Settings
In order to optimise the settings of your receiver for your TV
set, additional settings may be made in the menu
Audio Video settings.
> Press the Menu key to call up the Main Menu.
> Use the arrow keys up down to select the line
Settings.
> Confirm by pressing OK. The sub-menu Settings
will be displayed.
(Fig. 5-4)
> Now use the arrow keys up down to highlight the
line Audio Video Settings.
15
(Fig. 5-4)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 15

16
> Confirm by pressing OK. The menu Audio Video
Settings will be displayed.
(Fig. 5-5)
> You can use the arrow keys up down to move the
marker within the menu, and to change the individual
positions as indicated. When selecting a menu item
please also note any additional notes displayed. The
following adjustments can be made:
5.3.1 Picture format
> Use the arrow keys left right to select the appro-
priate picture format for your TV set, either 4:3 or
16:9. This function allows the picture format to be
adjusted automatically for your television set.
5.3.2 Language (Audio signal)
> Use the arrow keys left right in this line to select
your preferred language. Where available, this
function will scan for all languages being transmitted,
and will automatically set your preferred language.
5.3.3 TV SCART-Modus
> Use the arrow keys left right in this line to select
either FBAS or RGB, whichever is appropriate for
your TV set. For standard sets, the default setting is
RGB.
5.3.4 Video system
> Use the arrow keys left right in this line to select
the broadcasting standard apprpriate to your TV set.
The options that can be selected are PAL BG (stan-
dard setting), PAL I and SECAM BG.
5.3.5 UHF output channel
See Point 4.4.
> Press the key Back to return to the menu Settings
or press the Menu key to return to normal operation.
The settings are automatically stored in memory.
6 Operation
Please note:
Before you can attend to the operation of the
unit, you should, if this was not already done
during the initial installation, carry out a pro-
gramme search (Point 7.4), and where necessary
configure the Favourites list (Point 7.1). Only
when this is completed will all the digital pro-
grammes available in your location be available
to you.
(Fig. 5-5)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 16

6.1 Switching on and off
> Switch the receiver on by pressing the On Standby
key, either on the receiver itself or on the remote
control unit.
> Pressing this key again on the receiver or on the
remote control will switch the receiver off again.
> The receiver is now in standby mode, and the display
on the receiver box front panel will show the time. If
the time is not displayed, this must still be entered into
the unit. To do this, switch the receiver on, and switch
to reception of any major channel, such as ZDF, to
enter the time automatically.
6.2 Programme Selection
6.2.1 Using the Programme up/down keys
> You can use the Programme up down keys on the
receiver or on the remote control to move up or down
the programme list one slot at a time.
6.2.2 Using the numeric keypad
> Simply enter the desired programme number via the
numeric keypad.
For example:
1for programme slot 1
1, then 4for programme slot 14
2, then 3, then 4for programme slot 234
When entering programme numbers with more than one digit,
you have approx. 3 seconds after entering a number to
continue to the next digit. If you wish to enter a programme
number with only one or two digits, you can speed up the
switching process by holding down the last number a little
longer.
6.2.3 Using the programme list
> Press the OK key.
The programme list will now be displayed.
(Fig. 6-1)
While in TV mode, only TV programmes will be displayed,
and only radio programmes will be displayed while the
receiver is in radio mode. The programme currently selected
will be highlighted.
> You can now use the arrow keys up down to
highlight the desired programme.
> Press the OK key to select the highlighted
programme.
> Use the arrow keys up down to scroll through the
list one line at a time.
> Use the arrow keys left right to scroll quickly
through the list one page at a time.
17
(Fig. 6-1)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 17

18
6.2.3.1 Selecting a list
The receiver is equipped with several programme lists, which
facilitate the finding of programmes. You can select either
your personal Favourites list (see Point 7.1), or you can
choose to have the programmes sorted according to the
Alphabet or by Provider.
> Press the OK key. The active programme list will be
displayed.
> You can now use the red function key (category) to
open a window with the available types of programme
lists (Favourites List, Provider and ABC ...).
The active programme list type is highlighted.
(Fig. 6-
2)
> Use the up down arrow keys to select, for exam-
ple, the programme list type ABC and confirm by
pressing OK.
The alphabetically sorted programme list, containing
all programmes, will be displayed.
(Fig. 6-3)
> Use the up down arrow keys to select the pro-
gramme you wish to view.
> Confirm by pressing OK.
6.2.4 Selecting blocked programmes
If a programme is selected that is blocked by the parental
control function, the note Unit PIN will be displayed on
screen
(Fig. 6-4)
> Enter your PIN code by means of the numeric
keypad.
The selected programme can now be viewed.
In order to facilitate viewing, the PIN code needs to be ente-
red only once while the receiver is in operation. The parental
control block will only be re-activated the next time the unit is
switched on.
6.2.5 Information box
Each time you switch programmes an information box will be
displayed briefly, indicating programme number and program-
me name
(Fig. 6-5) . In addition, further programme characte-
ristics will be displayed, such as TxT for Videotext, 16 9 for
a 16/9 format broadcast, A B for different audio channels
(e.g. multilingual movie or various radio stations) and a key
for encrypted programmes.
6.3 Volume control
You have the facility to adjust the volume of your receiver.
This makes operating the receiver even easier, since it
means you have all the important functions on the remote
control of the receiver, and will only rarely have to use the
remote control of your TV set.
(Fig. 6-2)
(Fig. 6-3)
(Fig. 6-4)
(Fig. 6-5)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 18

19
When switching on the receiver from standby, sound will be
produced at the volume level last set.
> The volume of your receiver can be increased by
using the Volume + key, or you can make it softer by
using the Volume - key.
> Press the Sound on off key to mute the sound,
press the key again to switch the sound back on.
6.4 Selecting a different language
Where a programme is broadcast in several languages, or
with several sound channels ( in the information box),
you can select a different language or sound channel as fol-
lows:
> Press the key Language selection. If available, a
list of the currently broadcast languages will be dis-
played on screen. (Fig. 6-6)
> Use the arrow keys up down to select the desired
language.
> Confirm by pressing OK.
You can now listen to the programme in the language
selected. Your receiver is also able to receive mono
broadcasts ( in the information box).
(Fig. 6-7)
6.5 TV/Radio switching
The pre-programming includes radio programmes as well as
television programmes. In Radio mode, the accompanying
TV picture is switched off, and only the programme name is
displayed on screen.
> Switch the receiver into Radio mode by pressing the
TV Radio key.
The receiver will now switch to the radio programme
last selected.
> Press the TV Radio key again to switch to the TV
programme most recently selected.
6.6 Return to last programme selected
> Press the Back key on the remote control to return to
the previous programme selected.
> Press the key again to return to the programme
viewed before.
(Fig. 6-6)
(Fig. 6-7)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 19

6.7 Display Time and Programme Information
This function allows you to view programme information
related to the programme currently selected.
> Press the blue key to display information for the
programme selected.
On the lower half of the screen you will see a display showing
current time, the name of the programme selected, as well as
the start and end times of the current programme, where
available from the broadcaster.
> If available, pressing the blue multi-function key will
display information relating to the next programme.
6.8 Additional Programme Information
Where available from the provider, additional programme
information can be obtained by pressing the function
Programme information.
> Press the yellow function key to open an additional
information window.
(Fig. 6-8)
You will again see information relating to the current
programme.
> Now press the yellow function key again to view
information relating to the next programme.
> Press the yellow key again to switch off the display.
6.9 Channel Information
> Press the green function key (Channel Information)
in order to view data relating to the channel selected.
(Fig. 6-9)
> The coloured multi-function keys can be used to obtain
and display additional Audio Video information,
Programme information and, where relevant,
information on the encryption system used.
> Press the Back key to exit from the channel
information.
6.10 Videotext
6.10.1 Using the Videotext decoder of your televisi-
on set
Wherever this is broadcast, videotext will be available to your
TV set. Use the remote control of your TV set to work with
videotext. Should you experience problems with your TV set,
such as video text and picture content being superimposed,
you should set your receiver to FBAS mode (Point 5.3).
20
(Fig. 6-8)
(Fig. 6-9)
bed_anl_DigiPal 1.qxd 23.01.03 14:42 Seite 20