brondell SWASH ECOSEAT 102 User manual

OWNER’S MANUAL
SWASH ECOSEAT 102
Swash®
Ecoseat

Attach Proof of Purchase to This Page
Adjunte prueba de compra a esta página
Joindre une preuve d’achat à cette page

1
CONTENTS
PRODUCT INFORMATION
Safety Information ...........................Page 2
Product Features ............................Page 2
Product Dimensions..........................Page 3
Product Parts................................Page 4
PRODUCT INSTALLATION
Installation Parts .............................Page 5
Connecting Cold Water Supply ................Page 5
Connecting Hot Water Supply .................Page 8
PRODUCT OPERATION
Swash Operation ............................Page 9
MAINTENANCE & TECHNICAL INFO
Technical Specifications ......................Page 10
Swash Cleaning .............................Page 11
Nozzle Cleaning .............................Page 11
Troubleshooting .............................Page 12
Warranty....................................Page 13
Contact ....................................Page 14
Español ....................................Page 16
Français ....................................Page 31

22
PRODUCT INFORMATION
SAFETY INFORMATION
PRODUCT FEATURES
Use this product only for its intended use as directed in
this manual.
Do not disassemble, repair or modify the product - service
should only be performed by a certified Brondell representative.
Do not submerge or spray water directly on or into the product.
Do not stand or drop heavy objects on this product and do not
insert any object into openings or hose.
Do not pull or stress the water supply hose.
Do not use harsh brushes or abrasive detergents to clean the
product, use only mild soap and a soft cloth for cleaning.
Hygienic Dual Wash Wands
The Swash uses two hygienic wash wands: one for posterior
cleansing and the other for feminine cleansing.
Non-Electric Operation
No electricity is required to use the Swash. All Swash functions are
operated by the convenient wash control dial and household
water pressure.
Easy Installation
No special tools, professional plumber, or electrical outlet required
for installation.
Ergonomic Design
The slow-close ergonomic lid and seat are designed to ensure the
most comfortable experience.
Self-cleaning Hygienic Wands
Before and after each use, the wash wands self-clean to help stay
free of build-up or debris.

33
Elongated Top View
Round Top View
Required Distance Between
Mounting Holes
PRODUCT DIMENSIONS
PRODUCT INFORMATION (cont.)

44
PRODUCT PARTS
1. Lid
2. Seat
3. Wash Wands
a. Posterior Wand
b. Front Wand
4. Temperature Control Dial
5. Wash Control Dial
6. Quick Release Button
7. Mounting Plate
8. Hot Water Inlet
9. Cold Water Inlet
6
9
8
1
3
ab
4
4
5
5
7
2

55
INSTALLATION PARTS
1. Mounting Bolt (2)
2. Barrel Nut (2)
3. Mounting Plate
4. Adjustable Bracket
5. Cold Water T-Valve With Washer
6. 27.5” Cold Water Braided Metal Bidet Hose
1
5
2
3
6
4
7. Teflon Tape
8. Rubber Washers
9. Hot Water Supply Cap
10. Hot Water ⁄” T-Valve
11. Pressure Cap & Connector
12. Hot Water Flex Tubing
7
8
910 11 12
PRODUCT INSTALLATION
CONNECTING THE COLD WATER SUPPLY
1. Existing Toilet Seat Removal
a. Lift hinge covers and use a screwdriver to remove the mounting bolts.
b. Remove the toilet seat.
Please read these instructions carefully before installing the Swash. Failure to do so could result
in flooding, leaking or damage to the product.
NOTE: Steps may vary by type of seat and toilet.

66
PRODUCT INSTALLATION (cont.)
3. Connect T-Valve to the Toilet Tank Fill Valve
a. Place the Rubber Washer into the T-Valve.
b. Install the T-Valve with the Rubber Washer to the
incoming water connection on the bottom of your
Toilet Tank.
4. Connect the Water Supply Line coming from the wall to
the bottom of the T-Valve.
5. Install Mounting Plate
a. Place Adjustable Mounting Plate over mounting holes
on toilet, rubber side faces down, curved edge faces
toward the toilet tank.
b. Place the Adjustable Brackets groove side down on
the center of the square opening in the Mounting Plate,
then insert Mounting Bolts through the Adjustable
Brackets and through the bolt holes in your toilet.
Be sure that the square Mounting Bolt Head is flush
with the sides of the Adjustable Bracket.
c. Slide barrel nut onto Mounting Bolts under the toilet
bowl and tighten to keep Mounting Plate in place.
NOTES:
• The T-Valve connects to the Fill Valve directly under
your Toilet Tank - it does not connect at the wall.
• Only connect to the cold toilet water supply line.
• If your water supply line is rigid, you may need to
replace it before continuing.
Steps 5b & 5c
Steps 3-4
Step 3a
toilet tank
t-valve
cold water
supply line
NOTES:
• You may wish to place a container under the tank to
catch any excess water.
• Do not continue without completing the above steps.
• Failure to do so could result in flooding, leaking or
damage to the Swash.
2. Turn o Water Supply Valve and flush toilet
a. Turn Water Supply Valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely
empty tank.
c. Disconnect water supply hose from toilet tank.
Do not disconnect from the Water Supply Valve.
Step 2c
CONNECTING THE COLD WATER SUPPLY (CONT.)

77
IMPORTANT:
• If you are only connecting the cold water supply, you
must install the provided Hot Water Supply Cap -
(see Page 5) over the hot water inlet on your Swash
Ecoseat (see diagram).
• Failure to connect or cap the hot water inlet will
result in leaking during use.
• If you wish to also connect your hot water supply,
then proceed to “Connecting the Hot Water Supply”
on page 8.
NOTES:
• If you follow the mounting directions in 6b and your
seat still won’t mount flush with the lip of your toilet,
depending on the width of your toilet’s bolt spread,
you can insert the bolts through the top brackets
above the main brackets on your mounting plate to
move your seat up another ¾ inches.
8. Connect the open end of the Bidet Hose to the T-Valve.
6. Attach the Swash to the Mounting Plate
a. Set the Swash flat on the toilet bowl in front of the
Mounting Plate and slide seat onto plate until it is
secure and “clicks” into place.
b. If the seat appears too short or too long for the toilet,
adjust the Mounting Plate accordingly. To adjust the
Mounting Plate, loosen Barrel Nuts underneath the
toilet and slide seat forward or backwards as needed.
Once the seat is lined up properly, tighten Barrel Nuts
to hold in place.
7. Connect the Bidet Hose to the Cold Water Inlet
a. Connect the Bidet Hose to the Cold Water Inlet.
Hand-tighten to secure. Take care not to twist the
Bidet Hose, excessively bend it, or strip the plastic
screw threads when screwing the hose onto the
bidet seat.
Step 6a
Step 7a
Step 8
CONNECTING THE COLD WATER SUPPLY (CONT.)

88
5. Turn On Water Supply
a. Open the main water supply valve slowly and check
for leaks.
PRODUCT INSTALLATION (cont.)
CONNECTING THE HOT WATER SUPPLY
NOTES:
• You should use a small container or towel to catch
any residual water from the hose.
CAUTION:
• Do not overtighten the Pressure Cap. You will risk
damaging the tubing.
IMPORTANT:
• Be sure to slide the Hot Water Flex Tubing over the
Pressure Connector until the tubing slides past the
“lip” of the Pressure Connector and it cannot go
any further.
3. Reconnect hot water supply line to the open end
(top) of the Hot Water ⁄" T-valve.
4. If it hasn’t been removed already, unscrew the
Pressure Cap covering the Hot Water T-valve.
a. Slide the Pressure Cap over one end of the Hot
Water Flex Tubing with the inside threads facing
towards the open end.
b. Push the Hot Water Flex Tubing over the
Hot Water T-valve.
1. Connect the Hot Water Supply
a. Locate the Hot Water Supply line in your bathroom
under your sink/wash basin and turn the Water Supply
Valve all the way o.
b. Drain the hot water line by turning the sink tap on the
hot setting until no more water comes out.
c. Disconnect Hot Water Supply Hose to sink from Shut
O Valve. You may have to use a ⁄" compatible wrench
or a similar tool (not supplied).
2. Install the Hot Water ⁄" T-valve and the small rubber
washers as needed onto the hot water shut o valve
under the sink.
c. Slide the Pressure Cap down until it meets the pressure
connector, then screw it securely in place.
d. Unscrew and separate the Pressure Cap from the
Connector Part. Slide the Pressure Cap, with the inside
threads facing the open end, over the opposite end
of the Hot Water Flex Tubing, then insert the Pressure
Connector into the same end. Attach this end into the
Hot Water Inlet on the bidet seat, then secure the tube
in place by screwing on the Pressure Cap.
Step 1c
Step 2 & 3
Step 4a
Step 4c