Brooks RFP V2 Series User manual

Operation & Installation Manual RFP V2 Series
Rev 1
Residential Fire Panels
RFP V2 Series
MA225 26/7/2019

This page has deliberately been left blank.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
1 of 50
Table of Contents
1INTRODUCTION ____________________________________________________ 4
1.1 Design Philosophy and the Brooks Approach -------------------------------------------------- 4
1.2 System Overview -------------------------------------------------------------------------------------- 4
2SYSTEM DESIGN ___________________________________________________ 5
2.1 Smoke / Heat Alarms --------------------------------------------------------------------------------- 5
2.1.1 Basic Information about your Smoke / Heat Alarm ................................................. 5
2.1.2 Photoelectric Model (EIB650iWX) ........................................................................... 5
2.1.3 Heat Model (EIB603CX) .......................................................................................... 6
2.2 Roof Space Heat Detectors ------------------------------------------------------------------------- 7
2.2.1 Overview .................................................................................................................. 7
2.2.2 Features................................................................................................................... 7
2.2.3 Specifications........................................................................................................... 7
2.2.4 Connection to RFP V2 ............................................................................................. 8
2.3 Limitations of Smoke / Heat Alarms--------------------------------------------------------------- 8
2.4 Locating Smoke / Heat Alarms --------------------------------------------------------------------- 9
2.4.1 Smoke Alarms ......................................................................................................... 9
2.4.2 Heat Alarms ............................................................................................................. 9
2.4.3 Checking Audibility of Smoke / Heat Alarms ......................................................... 10
2.5 Recommended Locations ------------------------------------------------------------------------- 10
2.5.1 Locations to Avoid ................................................................................................. 10
2.6 Interconnecting Smoke/Heat Alarms ----------------------------------------------------------- 11
2.7 Smoke / Heat Alarm Additional Features ------------------------------------------------------ 11
2.8 Nuisance Alarms------------------------------------------------------------------------------------- 11
2.9 Important Safeguards------------------------------------------------------------------------------- 12
2.10 Fire Safety--------------------------------------------------------------------------------------------- 12
2.10.1 Planning Your Escape ........................................................................................... 12
2.10.2 Fire Safety Hints .................................................................................................... 13
3RESIDENTIAL FIRE PANEL __________________________________________ 14
3.1 RFP V2 Specifications------------------------------------------------------------------------------ 14
3.2 Familiarisation ---------------------------------------------------------------------------------------- 15
3.3 Features:----------------------------------------------------------------------------------------------- 15
3.3.1 Indicators of RFP V2.............................................................................................. 18
3.3.2 Controls of RFP V2................................................................................................ 18
3.4 RFP V2 Panel Mounting --------------------------------------------------------------------------- 18
3.5 Zone Termination------------------------------------------------------------------------------------ 18
3.6 RFP V2 Compatible Equipment------------------------------------------------------------------ 19
3.6.1 New Smoke / Heat Alarms..................................................................................... 19
3.6.1 Other Equipment.................................................................................................... 19
3.6.2 Discontinued Alarms.............................................................................................. 19
3.7 Power Supply----------------------------------------------------------------------------------------- 19
3.7.1 Primary Power Supply / Battery Charger............................................................... 19
3.7.2 Standby Supply...................................................................................................... 19
3.8 Termination of Field Wiring------------------------------------------------------------------------ 20
3.8.1 Smoke/Heat Alarm Inputs...................................................................................... 20
3.8.2 Mains Voltage Input ............................................................................................... 20
3.8.3 Battery Input .......................................................................................................... 20
3.8.4 Panic Input ............................................................................................................. 21
3.8.5 Common Alarm Outputs ........................................................................................ 21
3.8.6 Alarm Confirmation Period (Selectable) ................................................................ 21
3.8.7 Defect Mode Output............................................................................................... 21

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
2 of 50
3.9 Options ------------------------------------------------------------------------------------------------- 21
3.9.1 Mimic Panel (Optional) .......................................................................................... 21
3.9.2Zone Output Facility (Optional).............................................................................. 21
3.9.3 Remote Zone Relay Board (SUB600) ................................................................... 22
3.9.4 Magnetic Door Holder Power Supply .................................................................... 22
3.10 Panel Status ------------------------------------------------------------------------------------------ 22
3.10.1 Normal ................................................................................................................... 22
3.10.2 Zone Alarm ............................................................................................................ 22
3.10.3 Zone Fault.............................................................................................................. 22
3.10.4 Low Battery............................................................................................................ 23
3.10.5 Ancillary Isolate Button .......................................................................................... 23
3.10.6 Alarm Locate Button .............................................................................................. 23
3.10.7 Sounder Silence Button ......................................................................................... 23
4INSTALLATION ____________________________________________________ 24
4.1 Surface Mounting Instructions-------------------------------------------------------------------- 24
4.2 RFP V2 Cable Terminations ---------------------------------------------------------------------- 24
4.2.1 AC Power............................................................................................................... 24
4.2.2 Field Wiring ............................................................................................................ 24
4.2.3 Battery.................................................................................................................... 24
4.3 Termination of EIB650iWX or EIB603CX Alarms-------------------------------------------- 25
5COMMISSIONING __________________________________________________ 29
5.1 Commissioning Tests------------------------------------------------------------------------------- 29
5.1.1 System Configuration ............................................................................................ 29
5.1.2 Ancillary Functions................................................................................................. 29
6TESTING _________________________________________________________ 30
6.1 Power Supply----------------------------------------------------------------------------------------- 30
6.2 Fire Mode Test --------------------------------------------------------------------------------------- 30
6.3 Zone Alarm Test ------------------------------------------------------------------------------------- 30
6.4 Zone Fault Test -------------------------------------------------------------------------------------- 31
6.5 As-Installed Diagrams and Installer's Statement--------------------------------------------- 31
6.6 Log Book----------------------------------------------------------------------------------------------- 31
6.7 Maintenance ------------------------------------------------------------------------------------------ 32
7TROUBLESHOOTING_______________________________________________ 33
7.1 False Alarms------------------------------------------------------------------------------------------ 33
7.1.1 Frequent Nuisance Alarms Occur ......................................................................... 33
7.1.2 Alarm Sounds for no Apparent Reason................................................................. 33
7.2 Faults --------------------------------------------------------------------------------------------------- 33
7.2.1 Line Fault ............................................................................................................... 34
7.2.2 Low Battery............................................................................................................ 34
7.2.3 Connection Fault.................................................................................................... 34
8SPARE PARTS ____________________________________________________ 35
8.1 Main Panel -------------------------------------------------------------------------------------------- 35
8.1.1 Smoke / Heat Alarms............................................................................................. 35
9BATTERY CAPACITY CALCULATION _________________________________ 36
10 BLOCK WIRING DIAGRAMS _________________________________________ 37
11 COMMISSIONING CHECKLISTS ______________________________________ 41
12 PRODUCT GUARANTEE ____________________________________________ 46
13 REVISION HISTORY ________________________________________________ 47

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
3 of 50
Table of Figures
Figure 1 Roof Space Heat Detectors .............................................................................................. 7
Figure 2 Connection of roof space detectors .................................................................................. 8
Figure 3 Removing Alarm Heads from EIB603CX or EIB650iWX ................................................ 12
Figure 4 RFP6V2 Overlay for 6 Zones .......................................................................................... 16
Figure 5 Standard Mimic Overlay (Optional) ................................................................................. 16
Figure 6 RFP12V2 / RFP18V2 Overlay for 12 or 18 Zone............................................................ 17
Figure 7 RFP V2 Termination Board ............................................................................................. 20
Figure 8 Interface Base BAX16..................................................................................................... 25
Figure 9 SUB1012 Terminals - Interface Card.............................................................................. 25
Figure 10 Ribbon cable from SUB1005......................................................................................... 26
Figure 9 Removing Alarm Heads from EIB603cX and/or EIB650iWX .......................................... 26
Figure 12 F800 Iss1 RFPV2.......................................................................................................... 37
Figure 13 F801 Iss1 – RFP12V2 / RFP18V2 ................................................................................ 38
Figure 14 F802 - RFP V2 with Options ......................................................................................... 39
Figure 15 DIP Switch Settings on Main Board (SUB350) ............................................................. 40
List of Tables
Table 1 Roof space heat detectors ................................................................................................. 7
Table 2 Specifications of RFP V2 residential panels .................................................................... 14
Table 3 Front display indicators .................................................................................................... 18
Table 4 Front display controls ....................................................................................................... 18
Table 5 DIP Switch Settings for SUB1012 .................................................................................... 27
Table 6 Battery capacity calculation.............................................................................................. 36

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
4 of 50
1 Introduction
1.1 Design Philosophy and the Brooks Approach
The general growing awareness of the need for early warning detection of fire,
coupled with a push by legislators, has led to a wider acceptance within the
community.
Brooks is a specialist fire detection company offering long experience in design,
manufacture and service of commercial and residential fire detection and warning
systems.
In keeping with our philosophy of innovation, flexibility, reliability and quality, Brooks
now offers a complete and comprehensive range of Smoke / Heat Alarms and
Residential Fire Panels (RFP).
Australian Standard AS3786:2014 and AS1603.3:2018 have established a
performance standard for Smoke and Heat Alarms for Domestic/Residential
applications. Not content to just offer individual products, Brooks has developed a
range of residential fire alarm panels to enable fire system engineering principles,
normally applied to commercial premises, to be adapted to residential situations.
The vast majority of fire fatalities - particularly residential - occur due to the inhalation
of smoke and toxic fumes. A correctly designed and installed RFP system provides
an effective LIFE SAFETY SYSTEM, which raises the alarm and maximises your
opportunity to escape.
1.2 System Overview
The Brooks RFP V2 Series of Residential Fire Alarm Panels complete with the
compatible Smoke / Heat Alarms provides an automatic fire detection and warning
system designed to meet the requirements of Australian Standard AS3786-2014,
AS1603.3:2018 and National Construction Code (NCC) of Australian.
An automatic Residential fire alarm system is comprised of components for
automatically detecting a fire, and the initiation of local warning devices. The
Residential Fire Panel (RFP) employs smoke or heat sensitive alarms with electronic
interconnect signalling, to initiate both audio and visual means of fire alarm warning.
It has the added important feature of supervising the zone circuitry for a fault
condition. The Defect Mode output provides a means of monitoring whenever the
system is placed either deliberately or accidentally into a non-standard condition. i.e.
total power loss, Panel switched off, detection device line fault, ancillary outputs
isolated.
Since the applications for such systems are indeed diverse, it was decided to offer a
Residential Fire Panel where the necessary features for the majority of applications
came standard within the one RFP. The system features and/or configuration, is user
definable. This allows true flexibility of design and ease of future upgrading or
modifications. The RFP system has options such as independent zone operation,
independent smoke alarm operation, fire emergency override, alarm confirmation
period, remote indication.
RFP Main Board DIP switch settings are master settings that take precedence over
the Smoke / Heat Alarm interface card SUB1012. Each zone is limited to a maximum
of 12 Smoke / Heat Alarms and ancillary equipment for control, e.g. alarm bells,
security interface, panic input, fire doors, air conditioning shutdown, visual indicators,
etc. Control of ancillary equipment is affected by means of relay contacts, or a DC
voltage output which operates on receipt of an alarm signal.
The Residential Panel uses discrete electronics for its circuit design and is housed
in a powder coated steel cabinet. This provides high reliability and ease of
installation.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
5 of 50
2 System Design
The Smoke / Heat Alarms should be installed in compliance with the requirements
of the NCC; for specific technical guidance of Australian Standards AS1670.6,
AS1670.1 and this manual should be used.
A properly designed early warning fire system ensures the alarm is given before the
escape route becomes blocked with smoke or heat. Therefore, smoke alarms must
be installed along the escape route, heat alarms would not give sufficient warning.
2.1 Smoke / Heat Alarms
2.1.1 Basic Information about your Smoke / Heat Alarm
A Smoke Alarm is an early warning device, used correctly it will detect the onset of
a fire, raise the alarm and give occupants valuable time to escape prior to the
evacuation path becoming unusable. In today’s modern homes natural material like
wood and cotton have all but been replaced by synthetics. The result is that when a
fire does occur it will burn much faster and much hotter than for natural materials. It
will give off visible smoke and toxic fumes at much greater levels. For this reason,
Brooks has used only photoelectric Smoke Alarms in the RFS V2 system. Research
indicates this technology is superior in performance to ionisation in residential
applications and is the overall best and most reliable type of smoke alarm technology
for use in the modern dwelling.
Heat Alarms are supplementary devices only; for those areas where Smoke Alarms
would not be suitable. Heat detection occurs usually once flames are present
therefore, they are not early warning. Heat alarms must not be the only detection
used and must be interconnected to all smoke alarms to provide the best warning
throughout the dwelling.
When using household protective devices, basic safety precautions should always
be followed.
Notes:
•When the power is first connected to the Smoke / Heat Alarms, it may sound
for 2-3 seconds and/or the LED may flash quickly for 10 seconds - this is
normal.
•A Smoke / Heat Alarm does not prevent fires.
•Install correctly, in the centre of the ceiling if possible.
•Test monthly or after servicing any existing fault.
•When the panel chirps every 20 seconds, it means that either the backup
battery has reached the low battery threshold (below 12V) or a wiring fault
exists in one or more zones. Restore the mains power immediately or call
for technical support for wiring fault.
•For the Photo-electric model EIB650iWX, if the Smoke Alarm beeps without
the LED flashing at the same time then clean the unit as this is the automatic
test feature telling you the chamber is degraded.
•Plan your escape route.
•Proper protection requires more multiple Smoke / Heat Alarm.
•If you have any doubt or query about Smoke / Heat Alarms consult the
nearest Brooks Office as shown in the last page.
2.1.2 Photoelectric Model (EIB650iWX)
Photoelectric Smoke Alarms senses visible smoke particles. They respond to a
sufficiently wide range of fires to be of general use, but are particularly responsive to
smouldering fires and the dense smoke given off by foam filled furnishings or

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
6 of 50
overheated PVC wiring. They are less prone to nuisance alarms from cooking
fumes. Furthermore, they contain no radioactive material.
However, all photoelectric Smoke Alarms are prone to nuisance alarms caused by
dust or insect contamination. Mesh screens are provided and are effective in
reducing insect ingress but it is impossible to make the Alarms dust or insect proof
since they would then be effectively smoke proof! For this reason, it is essential that
photoelectric Smoke Alarms are always kept clean. The recommended areas to
install photoelectric Smoke Alarms are in bedrooms and living areas adjacent to
kitchens. Refer to the EIB650iWX leaflet.
Operating Principle: Light scattering – a transmitter produces pulses of light which
are detected by a receiver when smoke enters the sensing chamber.
2.1.3 Heat Model (EIB603CX)
Heat Alarms require less maintenance than photoelectric Smoke alarms. There are
locations where the installation of a Smoke Alarm is not recommended, e.g. kitchens,
laundries, garages, etc. Yet these areas are a potential of fires and the need for an
alternative method of fire detection is, in the opinion of many fire officers and
specifiers, essential in this and other vulnerable locations of residential properties.
The Heat Alarm EIB603CXCX provides such an alternative. Fixed temperature heat
alarms are designed to trigger when the temperature reaches approximately 58ºC.
The heat alarm is not sensitive to smoke, but in a closed room with a vigorous fire
they will tend to respond faster than a Smoke Alarm a distance away in the hallway.
A Heat Alarm MUST be interconnected to your Smoke Alarms so that the Alarm can
be heard throughout the building.
Operating Principle: Thermistor sensor - resistance value varies with temperature.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
7 of 50
2.2 Roof Space Heat Detectors
2.2.1 Overview
Figure 1 Roof Space Heat Detectors
Standard Smoke or Heat Alarms are not suitable for residential roof space
applications where fire may occur.
Brooks has developed a solution to protect residential roof space when a residential
fire panel is used. The heat detector utilises a bi-metallic heat switches to detect
temperature rise in the roof space.
When the temperature in the roof space reaches the set point of the bi-metallic
switch, the contact of the switch will close and connects approximately 12V (with a
diode forward voltage drop) to the interconnect which activates all Smoke or Heat
Alarms within RFP V2 series. Roof space detectors available for 60⁰ C or 80⁰ C
applications.
2.2.2 Features
•Minimum current draw, refer to Table 1 below.
•Up to 10 of HS60V2 or HS80V2 can be connected to RFP V2 series.
•Minimise false alarms.
•Suitable for harsh environment e.g. roof spaces, garages, etc.
•Built-in alarm LED indication
•Support Remote Indicator Light (RIL), with selectable “Latching” and “Non-
Latching” mode
2.2.3 Specifications
Table 1 Roof space heat detectors
Function HS60V2 HS80V2
Temperature 60°C ±5°C 80°C ±5°C
Current Consumption(@12.8V)
Quiescent
Alarm (without RIL)
Alarm (with RIL)
0.1 uA
6.7 mA
14 mA
0.1 uA
6.7 mA
14 mA
Nominal Voltage 12 V 12 V
No. of units per zone 10 10
Dot Colour Blue Red
Size 73mm diameter 73mm diameter

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
8 of 50
2.2.4 Connection to RFP V2
Field wiring as shown in Figure 2 below is same as the standard RFP zone wiring.
The bi-metallic switch contact is connected between Interconnect and positive
terminals (with protection diode and series resistor) on SUB1034 (60⁰) / 1035 (80⁰)
board. When the temperature in the roof space reaches the fixed temperature value,
the bi-metallic N/O contact closes, Interconnect voltage goes high and activates all
the Smoke or Heat Alarms interconnected to HS60V2 or HS80V2. The red LED will
turn on only when the heat switch closes. The roof space heat detector provides 12V
output for Remote Indicator Light (RIL), with selectable “Latching” and “Non-
Latching” mode. The RIL will be reset when key-switch on the panel is switched to
“OFF” or “FIRE” position.
Figure 2 Connection of roof space detectors
2.3 Limitations of Smoke / Heat Alarms
Smoke / Heat Alarms have significantly helped to reduce the number of fire fatalities
in Australia where they are widely installed.
However, independent authorities have stated that they may be ineffective in some
circumstances. There are a number of reasons for this:
•Smoke / Heat Alarms will not work if they are not connected to the RFP6 V2
series or if the power supply of the panel has failed.
•Smoke / Heat Alarms will not detect fire if sufficient smoke / heat does not
reach or prevented to reach the Alarm. Smoke/Heat may be prevented from
reaching the Alarm if the fire is too far away, for example, if the fire is on
another floor, behind a closed door, in a chimney, in a wall cavity, or if the
prevailing air draughts carry the smoke/heat away. Installing Smoke/Heat
Alarms on both sides of closed doors and installing more than one
Smoke/Heat Alarm as recommended in this manual very significantly
improves the probability of early detection.
•Smoke / Heat Alarms which are not maintained or are tampered may not
function reliably.
•Smoke / Heat Alarms may not be heard due to background noise, distance
from the bedroom or closed doors.
•A Smoke / Heat Alarms may not wake a person who has taken drugs or
alcohol.
•Smoke / Heat Alarms may not detect every type of fire to give sufficient early
warning. They are particularly ineffective with fires caused by escaping gas,
violent explosions, poor storage of flammable rags and/or liquids, (for
example petrol, paint, spirits etc). Overloaded electrical circuits, arson and
children playing with matches.
•Smoke / Heat Alarms do not last indefinitely. The manufacturer recommends
replacement after 10 years as a precaution.
EOL
Device

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
9 of 50
2.4 Locating Smoke / Heat Alarms
The locations are typically required to meet the Deemed to Satisfy Provisions of the
NCC. However, the NCC does not provide specific guidance as to the minimising of
potential nuisance alarms. There will be dwelling layouts that require further
consideration to avoid locating the Alarm so that it is not triggered from everyday
events such as showers or cooking. This manual as well as AS1670 parts 1 and 6
provides technical guidance with respect to installation.
2.4.1 Smoke Alarms
Sufficient smoke must enter the Smoke Alarm before it will respond. The Smoke
Alarm needs to be within 7.5 metres of the fire to respond quickly. It also needs to
be in a position where its alarm sounder can be heard throughout the residence, so
it can wake all occupants in time for all to escape. As a minimum a Smoke Alarm
should be located between the sleeping area and the most likely sources of fire
(living room or kitchen for example). A single Smoke Alarm will give some protection
if it is properly installed, but most residence will require two or more Smoke Alarms
to ensure a reliable early warning is given. For maximum protection you should put
individual Smoke Alarms in all the rooms where fire is most likely to break out, apart
from kitchens, laundries and garages (see locations to avoid).
Note: Some state legislation mandates a Smoke Alarm in every room and hallway in
the dwelling.
The living room is the most likely place for a fire to start at night, followed by the
kitchen and then the dining room. You should also consider putting Smoke Alarms
in any bedrooms where fires might occur. For instance, where there is an electrical
appliance such as an electric blanket or where the occupant is a smoker. You could
also consider putting Smoke Alarms in any rooms where the occupant is unable to
respond very well to a fire starting in the rooms, such as an elderly, sick person or a
very young child.
Refer to the Smoke Alarm EIB650iWX and the Heat Alarm EIB603CX leaflets for
more details.
2.4.2 Heat Alarms
The Heat Alarm gives a fire warning when the temperature at the unit reaches
approximately 58⁰C. It is ideal for kitchens, garages, boiler houses and other areas
where there are normally high levels of fumes, smoke or dust i.e. places where
Smoke Alarms cannot be installed without the risk of excessive nuisance alarms.
A Heat Alarm should only be used in a room adjoining an escape route, and must
be used in conjunction with Smoke Alarms on the escape routes.
The Heat and Smoke Alarms are interconnected with RFP6 V2 to ensure the early
warning will be heard, particularly by somebody sleeping. A properly designed early
warning fire system ensures the alarm is given before the escape routes become
blocked with smoke or heat. Therefore, there must be Smoke Alarms along the
escape routes as Heat Alarms would not give sufficient warning.
However, a fire in a closed room (e.g. kitchen) adjoining the escape route, can
eventually cause the corridor to become smoke-logged due to smoke leaking out
from around the door before adequate warning can be given by detectors in the
corridor. (Smoke leaking out from a room is often cool and slow moving so it can
take a long time to rise to the ceiling, and travel to a detector which could be some
distance away). A Heat Alarm in the closed room will give earlier warning of fire in
that room and help overcome this problem.
This type, with consideration to the above, can be installed in kitchens, laundries,
garages and boiler houses and other areas where there are normally high levels of
fumes, smoke or dust i.e. places where smoke alarms cannot be installed without
the risk of excessive nuisance alarms.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
10 of 50
Important: These Smoke/Heat Alarms are designed for use in a residential type
environment.
2.4.3 Checking Audibility of Smoke / Heat Alarms
With the Alarm sounding in its intended location, check that you are able to hear it in
each bedroom with the door closed above the sound of your radio. The radio should
be set to a reasonably loud conversation level. If you can’t hear it over your radio,
the chances are it would not wake you.
The Smoke / Heat Alarms are interconnectable meaning that when one Alarm within
a zone senses smoke or heat, all connected Alarms will go into alarm.
Note: Options within the Smoke Alarm and Residential Fire Panel enable
customising of the installation. However, the sound levels are fixed and cannot be
adjusted.
2.5 Recommended Locations
For the best location and maximum protection, refer to EIB650iWX and EIB603CX
manuals.
2.5.1 Locations to Avoid
Don’t place your Smoke Alarm in any of the following areas:
•Kitchens, Bathrooms, shower rooms, garages or other rooms where the
Smoke Alarm may be triggered by steam, condensation, normal smoke or
fumes. Keep at least 6 metres away from sources of normal smoke/fumes.
Don’t place Heat Alarms in any of the following areas:
•Bathrooms, shower rooms or other room where the unit may be affected
by steam or condensation.
Don’t place Smoke or Heat Alarms in any of the following areas:
•Places where the normal temperature can exceed 45°C or be below 5°C
(e.g. attics, furnace rooms, directly above ovens or kettles etc.) as the
heat/steam could cause nuisance alarms.
•Near a decorative object, door, light fitting, window moulding etc., that may
prevent smoke or heat from reaching the Alarm. Heat from light fittings may
prevent or delay the smoke reaching the detection chamber.
•Surfaces that are normally warmer or colder than the rest of the room (for
example attic hatches, uninsulated exterior walls etc), Temperature
differences might stop smoke from reaching the unit.
•Next to or directly above heaters or air conditioning vents, windows, wall
vents etc. that can change the direction of airflow.
•In very high or awkward areas (e.g. over stairwells) where it may be difficult
to reach the alarm (for testing, maintenance etc).
•Locate unit at least 1.5m and route wiring at least 1m away from fluorescent
light fittings as electrical “noise” and/or flickering may affect the unit.
•Locate away from very dusty or dirty areas as dust build-up in the chamber
can make unit too sensitive and prone to alarm. It can also block the insect
screen mesh and prevent smoke from entering the chamber.
•Do not locate in insect infested areas. Small insects getting in to the
chamber can cause intermittent alarms. Insects and contamination on the
Heat Alarm sensor can increase its response time.
•Locate the Alarm at least 1m from dimmer controlled lights and wiring as
some dimmers can cause interference.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
11 of 50
2.6 Interconnecting Smoke/Heat Alarms
The Brooks Smoke Alarm EIB650iWX and Heat Alarm EIB603CX provide an
interconnect facility to RFP V2 series. When one Smoke/Heat Alarm activates all
Smoke/Heat Alarms and panel buzzer will sound, this provides not only an increased
sound pressure level but also an alarm warning throughout the entire dwelling. Up
to 12 Smoke / Heat Alarms model EIB650iWX, and/or EIB603CX can be
interconnected to each zone in RFP V2 series.
The unit initiating the alarm can be identified by the red LED on the cover flashing
every second, or by pressing the alarm locate (interlocked with Fire Mode) switch on
the RFP front face plate.
Note: If obsoleted X series Alarms already exists, they can still be used provided
they are not over 10 years old and are still working.
The panel is compatible with either the obsoleted smoke alarms and/or the current
EIB603CX and/or EIB650iWX.
2.7 Smoke / Heat Alarm Additional Features
The new series of Smoke (EIB650iWX) and Heat (EIB603CX) Alarms have similar
features to the discontinued X series Alarms in addition to some new added features:
•Remote Indicator Output (RIL) output: This enables an RIL to be located
outside a door to indicate the origin of the alarm.
•Alarm can be isolated be removing the head from the base.
•Removing the head will keep all the other Alarms in the same zone in
operation.
•EIB650iWX is a microprocessor-based design which allows for more
features.
2.8 Nuisance Alarms
Smoke Alarms are sensitive devices that may also be triggered by other household
activities like cooking or steam from showers or laundries. Remember, your Smoke
Alarm can be triggered by you accidentally, this does not mean it is faulty it has
simply detected something that to it simulates smoke.
If there is a nuisance alarm simply press the “Locate” button and turn the key switch
to “Fire” on the front display of the RFP system, this will identify the activated Alarm.
Once the source of nuisance alarm is located, fan the smoke alarm to clear the
smoke. If, when the Alarm goes off, there is no sign of smoke, heat or noise to
indicate that there is a fire, you should get your family into a safe place, before you
start investigating.
Check the house carefully in case there is a small fire smouldering somewhere.
•Check whether there is some source of smoke or fumes, for example
cooking fumes being drawn past the Smoke Alarm by an extractor.
•Fan the sensing chamber vigorously with a newspaper or similar to clear
and silence the alarm.
•If there are frequent nuisance/false alarms, it may be necessary to re-
locate the device away from the source of the fumes. If for some reason
the Alarm continues to sound (due to insect infestation or contamination
build up for example), do the following:
Remove the Smoke / Heat Alarm causing nuisance alarm as shown in Figure 3
below. For EIB650iWX and/or EIB603CX, remove the head by disconnecting the

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
12 of 50
adapter board off the Alarm, panel will go into fault. Push the Sounder Silence button
on the panel to stop the panel from beeping if it occurs at night while you are
sleeping. Replace your alarm next earliest as soon as possible.
Note: When an Alarm is removed, all other Alarms in the zone will continue working
and communicate with the RFP system.
Figure 3 Removing Alarm Heads from EIB603CX or EIB650iWX
2.9 Important Safeguards
When using household protective devices, basic safety precautions should always
be followed, including those listed below.
•Familiarise yourself with the RFP system operation.
•Rehearse emergency escape plans so everyone in the premises knows
what to do in case the alarm sounds.
•Do not disconnect wires to stop alarm sounding. (Fanning vigorously with a
newspaper or similar will remove nuisance smoke from the Smoke Alarm
and stop it sounding).
•To maintain sensitivity to smoke, do not paint or cover smoke alarm in any
manner; do not permit any accumulation of cobwebs, dust or grease.
•If unit has been damaged in any way or does not function properly, do not
attempt a repair, return the Alarm to the nearest Brooks office.
•Smoke/Heat Alarms are intended for premises having a residential type
environment.
•Smoke / Heat Alarms are not a substitute for insurance, the manufacturer is
not your insurer.
2.10 Fire Safety
2.10.1 Planning Your Escape
Use the Smoke / Heat Alarm test button or the key switch on the inner door to
familiarize occupants with the alarm sound and to practice fire drills regularly with all
family members. Draw up a floor plan that will show each resident at least 2 escape
routes from each room. Children tend to hide when they don’t know what to do.
Teach children how to escape, open windows, and use roll up fire ladders and stools
without adult help. Make sure they know what to do if the alarm goes off.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
13 of 50
2.10.2 Fire Safety Hints
•Store petrol and other flammable materials in proper containers.
•Discard oily or flammable rags.
•Always use a metal fireplace screen and have chimneys cleaned regularly.
•Replace worn or damaged sockets, switches, home wiring and cracked or
frayed electrical cords and plugs.
•Do not overload electrical circuits.
•Do not overload any zone circuit, max of 12 Alarms can be connected to a
zone.
•Use the recommended cables shown in Table 2 below.
•Never smoke in bed. In rooms where you do smoke, always check under
cushions for smouldering cigarettes and ashes.
•Be sure all electrical appliances and tools have a recognised approval label.
•Smoke Alarms cannot protect all persons at all times. It may not protect
against the three most common causes of fatal fires:
oSmoking in bed.
oLeaving children at home alone.
oCleaning with flammable liquids, such as petrol.
Further information can be obtained from Brooks Australia’s Guide to Residential
Fire Safety.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
14 of 50
3 Residential Fire Panel
3.1 RFP V2 Specifications
Table 2 Specifications of RFP V2 residential panels
Feature Specification
No. of zones 6, 12 or 18
Max. no. of Alarms 12 Alarms per zone
Enclosure Zinc steel 1.5mmm powder coated oyster
RFP6 V2: 400mm H x 320mm W x 135mm D
RFP12 /18: 6800mm H x 320mm W x 135mm D
Power Supply Input: Universal 88 – 264VAC, 50W
Output: 13.5-16.5 VDC adjustable, 50W (3.4A)
Nominal: 14.5VDC, 13.8VDC on battery terminals
Standby Supply 12V SLA batteries 7-30 AH1depending on total number
of Alarms fitted
Battery low setting 12.0 VDC
Key switch Operation “ON” System ON - Charger ON
“OFF” System OFF - Charger ON
“FIRE” activates all smoke/heat alarms
System Monitoring Separate terminals for zone wiring loop in and out to
every Alarm, monitored either by EOL device
or DIP
switch setting in the last Alarm
Fault (defect) Mode Initiated by an abnormal system condition:
* Total power loss
* Ancillary outputs (common alarm) Isolated
* Short / Open circuit line fault
* System switched off
Fault Output 1 set changeover relay contact
Alarm Outputs 12VDC / 1 Amp maximum, non-supervised
1 set changeover relay contact
Panic Input Non-supervised N/O contact - activates all Alarms
Sounder Silence Switch Acknowledges panel sounder
Alters tone from continuous to chirp (for battery low and
zone wiring fault)
Ancillary Isolate Switch
Isolates common alarm outputs and initiate Defect
Mode
Alarm Locate Switch Silences all Smoke/Heat Alarms except those initiating
the alarm.
1When larger battery capacity required, up to 2 x 15AH / 12V batteries can be paralleled to double the
battery size.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
15 of 50
Visual Indications Individual zone alarm - Red
Individual zone fault - Amber
Ancillary isolate - Amber
Locator activated2- Amber
Sounder silence - Amber
Power ON - Green
Smoke/Heat Alarms options Remote indication output set to latching or non-latching.
Standalone or common alarm operation. Refer to Table
5 page 27
Panel Features DIP Switch
Setting on SUB350
•Common or individual zone operation
•Latching or non-latching alarm indication
•
Alarm confirmation period: 0 Sec, 30 Sec or 60
Sec
•Common Alarm Output latching or non-latching
OPTIONS
Zone Output Card SUB365 1 set C/NO/NC changeover relay contact per zone
1 set C/NO relay contact per zone
Mimic Panel (Custom built) 24 Smoke/Heat Alarm indications or
48 Smoke/Heat Alarm indications or
72 Smoke/Heat Alarm indications
Field Wiring Cables 4 Core min. 1mm²
, red Brooks BAC4C1/100 or
BAC4C1/250
3.2 Familiarisation
The purpose of this section is to make you familiar with the operation and
construction of the RFP V2 range of Residential Fire Panels. The basic configuration
of RFP V2 is the six-zone residential panel RFP6V2 which consists of the following:
•Main control and display board SUB350, contains zone indicators, control
switches and 003 key switch interface.
•Field wiring termination board SUB357
•6 x End of line module SUB360
•Switch mode power supply 50W BAPS15V50W
•12V Back up battery, capacity 7-15 AH, can also accommodate 2 x 7-15 AH
batteries in parallel to double the battery capacity 14-30 AH housed in the
small or large enclosure.
An optional zone output card (SUB365) can be fitted within the same enclosure.
Optional Smoke / Heat Alarm mimic panel in a separate enclosure is also available.
3.3 Features:
•Individual Zone alarm and fault indicators
•Latching / non-latching alarm indicator (selectable)
2Pressing only the locate button will lead to no action unless preceded by fire mode key switch.

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
16 of 50
•Common alarm output confirmation (delay), 0, 30 and 50 second.
•003 Key switch to turn the RFP ON / OFF or FIRE mode.
•Individual zone relay output when the optional zone output card SUB365 is
fitted.
•Alarm locate facility to identify activated Smoke/Heat Alarm.
•Ancillary isolate control to isolate the common alarm output.
Figure 4 below shows the front view of the standard 6 zone residential fire panel
RFP6 V2 and Figure 5 shows the front view of the optional 24 LED mimic display.
Figure 4 RFP6V2 Overlay for 6 Zones
Figure 5 Standard Mimic Overlay (Optional)
The RFP12/18 V2 comprises the same components as in RFP6 V2. In addition, a
slave main board SUB350S and a standard termination board SUB357 are added
for every 6 zone, all housed in a larger enclosure. The front view of RFP12/18 V2 is
shown in Figure 6 below.below

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
17 of 50
Figure 6 RFP12V2 / RFP18V2 Overlay for 12 or 18 Zone

Operation & Installation Manual RFP V2 Series
MA225 Rev 1
18 of 50
3.3.1 Indicators of RFP V2
Table 3 Front display indicators
Descriptor Colour Function Buzzer
On Green Steady On, mains power ok No
Alarm Red
Steady On: Zone 1 – 6 for RFP6 and
Zone 7 – 12 for RFP12 and
Zone 12 -18 for RFP18
Yes
Fault Amber Steady On zone 1 to zone 6 Yes
3.3.2 Controls of RFP V2
Table 4 Front display controls
Descriptor Function
Key Switch
“ON” System ON - Charger ON
“OFF” System OFF - Charger ON, no power to Smoke/Heat
Alarms
“FIRE” activates all Smoke / Heat Alarms
Locate Identifies active Smoke / Heat Alarm causing fire
Ancillary Isolate Isolate common alarm outputs, sounder On
Sounder Silence Silences all active Smoke and Heat Alarms for 10 minutes
3.4 RFP V2 Panel Mounting
The control panel (RFP) should be located in a common area inside the residence,
IP enclosures are also available if the RFP required to be outside. The RFP must be
secured on a wall and be wired to the 230VAC supply to the dwelling by a licensed
electrician to a dedicated circuit. A mains isolate switch is provided to terminate the
mains power inside the cabinet and Earth stud to ensure earthing the metal
enclosure.
3.5 Zone Termination
Each Zone has separate terminals to interface the RFP to the Smoke/Heat Alarms
via 3 wires to supply 12VDC and interconnection across each zone, see Figure 7,
page 20. Zone power to the Alarms is protected with 1 A fuse. A forth wire will be
required for common fire mode if the Smoke Alarm is set to independent. As the
standard cables are supplied as a 4 core cable, the common practice is to terminate
the fourth wire to each Smoke / Heat Alarm as shown in the RFP block wiring
diagrams in Figure 12 page 37, Figure 13 page 38 and Figure 14 page 39.
The three wires are fully supervised by the RFP for open or short circuit fault via EOL
device SUB360. A fault indicator for each zone is provided and a panel buzzer to
provide audible indication. When the buzzer is silenced, a chirp every 20 second will
be given.
Note: If EOL device SUB360 is not used, the last smoke / heat alarm can be set to
be EOL using the DIP switch setting on the interface board SUB1012.