Brother DCP-110C User manual

Quick Setup Guide DCP-110C
DCP-310CN
Before you can use the machine, you must set up the hardware and install the driver.
To help you get started in setting up the machine and installing the driver and software,
please read this “Quick Setup Guide” and follow the simple instructions.
For the latest drivers and to find the best solution for your problem or question, access the Brother
Solutions Center directly from the driver or go to http://solutions.brother.com
Keep this “Quick Setup Guide”, User’s Guide and supplied CD-ROM in a convenient place for
quick and easy reference at all times.
Version B
Step 1
Setting Up the Machine
Step 2
Installing the Driver & Software
Setup is Complete!
Installing the Driver & Software
Setting Up
the Machine
Windows®
Mac OS®
8.6 - 9.2
Mac OS®X Windows®
Network
Macintosh®
Network
For
Network Users

■
Warning Hint User’s Guide
Indicates warnings that
must be observed to
prevent possible
personal injury.
Indicates cautions that
must be observed to use
the machine properly or
to prevent damage to the
machine.
Indicates notes and
useful tips to remember
when using the machine.
Indicates reference to the
User’s Guide.

1
Carton components may differ from one country to another.
Save all packing materials and the carton.
Carton Components
Quick Setup Guide
CD-ROM
User’s Guide
Power Cord Control Panel
Black
(LC900BK)
Magenta
(LC900M)
Yellow
(LC900Y)
Cyan
(LC900C)
Ink Cartridges
If you are connecting the machine via USB:
■The interface cable is not a standard accessory. Please purchase an appropriate USB 2.0 interface
cable.
■Please make sure you use a USB 2.0 that is no longer than 2 metres.
■Your machine has a full speed USB 2.0 interface. This interface is compatible with Hi-Speed USB 2.0;
however, the maximum data transfer rate will be 12 Mbits/s. The machine can also be connected to a
computer that has a USB 1.1 interface.
DCP
■Getting Started

2
Control Panel
1. Copy keys 5. Start keys 9. PhotoCapture key
2. Set key 6. On/Off key 10. Menu key
3. Navigation keys 7. Ink key 11. Liquid Crystal Display (LCD)
4. Stop/Exit key 8. Scan key
For the details of the control panel, see "Control panel overview" in Chapter 1 of the User’s Guide.
1 2 4 53
1011 9 8 7 6

3
Table of Contents
Setting Up the Machine
1. Removing the Protective Parts ......................................................................... 4
2. Attaching the Control Panel.............................................................................. 4
3. Loading Paper .................................................................................................... 4
4. Installing the Power Cord..................................................................................5
5. Selecting Your Language ..................................................................................5
6. Installing the Ink Cartridges.............................................................................. 5
7. Print Quality Check ............................................................................................ 8
8. Setting the Date and Time ................................................................................. 9
Installing the Driver & Software
Supplied CD-ROM (MFL-Pro Suite).................................................................... 10
For USB Interface Cable Users
(For Windows®98/98SE/Me/2000 Professional/XP) ......................................... 12
For Network Interface Cable Users (DCP-310CN only)
(For Windows®98/98SE/Me/2000 Professional/XP) ......................................... 15
For USB Interface Cable Users .......................................................................... 18
■For Mac OS®8.6 to 9.2 .......................................................................................18
■For Mac OS®X 10.2.4 or greater........................................................................20
For Network Interface Cable Users (DCP-310CN only) .................................... 23
■For Mac OS®8.6 to 9.2 Users ............................................................................23
■For Mac OS®X 10.2.4 or greater Users.............................................................25
■For Network Users (DCP-310CN only)
Network User's Guide Chapter Map .................................................................. 28
Restoring the Network Settings to Factory Default ......................................... 28
Installing the BRAdmin Professional Configuration Utility
(Windows®Users Only) .................................................................................... 29
Setting your IP Address, Subnet Mask and Gateway using
BRAdmin Professional (Windows®Users Only)............................................. 30
■Consumables and Options
Replacement Consumables................................................................................ 31
Option ................................................................................................................... 31
Step 1
Step 2

4
Setting Up the Machine
1Remove the protective tape.
DO NOT connect the USB cable.
Connecting the USB cable is done
when installing the driver.
1Attach the control panel to the machine.
1Pull the paper tray completely out of the
machine and remove the output paper tray.
2Press and slide the paper guide to fit the
paper width.
3Pull out the paper support and unfold the
paper support flap.
4Fan the stack of paper well to avoid paper
jams and mis-feeds.
5Gently insert the paper into the paper tray
print side down and top edge first.
Check that the paper is flat in the tray and
below the maximum paper mark.
6Put the output paper tray back on and push
the paper tray firmly back into the machine.
1Removing the Protective
Parts
2Attaching the Control
Panel
3Loading Paper
You can load up to 100 sheets of 80 g/m2
paper.
For more details, see “About paper” in
Chapter 1 of the User’s Guide.
Use the paper support flap for Letter, Legal
and A4 size paper.
■Make sure the paper side guides touch
the sides of the paper.
■Be careful that you do not push the paper
in too far; it may lift at the back of the tray
and cause paper feed problems.
Paper Side Guide
Paper Support Flap
Paper Support
Step 1

5
Setting Up
the Machine
Windows®
Mac OS®
8.6 - 9.2
Mac OS®X Windows®
Network
For
Network Users Macintosh®
Network
1Connect the power cord.
DO NOT connect the USB cable yet.
Warning
The machine must be fitted with an earthed plug.
1After connecting the power cord, the LCD
shows:
Press Set.
2Press ▲or ▼to select your language and
press Set.
3If your language is selected, press ▲(Yes).
Warning
If ink gets in your eyes wash them with water
immediately, and if irritation occurs consult a doctor.
1Make sure that the power is turned on.
The LCD shows:
2Lift the scanner cover from the right-hand
side of the machine until it locks securely
into the open position.
3Remove the protective parts.
4Installing the Power
Cord
5Selecting Your
Language
Select Language
Press Set Key
English
Select▲▼ & Set
English?
▲Yes ▼No
If you have set the language wrongly, you
can change the language after setting the
date and time. (For details, see “How to
change LCD language” in Chapter 5 of the
User’s Guide)
(Example for the U.K.)
6Installing the Ink
Cartridges
No Cartridge
Do not throw away the protective parts.
You will need them when you transport the
machine.
Scanner Cover
Continued...

6
Setting Up the Machine
4Take out the ink cartridge.
5Carefully remove the buttom cap.
DO NOT touch the area shown in the
illustration below.
Keep the ink cartridge in an upright position
when you insert it into the slot.
6Press firmly down on the ink cartridge until
the hook snaps over it, taking care to match
the slot colour (A) with the cartridge colour
(B), as shown in the diagram below.
7Lift the scanner cover to release the lock.
Gently push the scanner cover support
down and close the scanner cover.
The machine will clean the ink tube system
for use for the first time. This process will
occur only once, the first time ink cartridges
are installed. The cleaning process will last
approximately four minutes.
The LCD shows:
If the cartridge cover comes off when you
open the bag the cartridge will not be
damaged.
Opening
OK
OK
OK
If Install shows on the LCD after you
install the ink cartridges, check to make sure
the ink cartridges are installed correctly.
Preparing System
Approx 4 Minutes
(B)
(A)
OK
OK
OK
Step 1

7
Setting Up
the Machine
Windows®
Mac OS®
8.6 - 9.2
Mac OS®X Windows®
Network
For
Network Users Macintosh®
Network
• DO NOT remove ink cartridges if
you do not need to replace them.
If you do so, it may reduce the ink
quantity and the machine will not
know the quantity of ink left in
the cartridge.
• DO NOT shake the ink cartridges.
If ink stains your body or
clothing, wash with soap or
detergent immediately.
• DO NOT dismantle or tamper
with the ink cartridge, this can
cause the ink to leak out of the
cartridge.
• Brother inkjet machines are
designed to work with ink of a
particular specification and work
to a level of optimum
performance when used with
genuine Brother ink cartridges.
Brother cannot guarantee this
optimum performance if ink or
ink cartridges of other
specifications are used. Brother
does not therefore recommend
the use of cartridges other than
genuine Brother cartridges with
this machine or the refilling of
empty cartridges with ink from
other sources. If damage is
caused to the print head or other
parts of this machine as a result
of the use of ink or ink cartridges
other than genuine Brother
products due to the
incompatibility or lack of
suitability of those products with
this machine, any repairs
required as a result will not be
covered by the warranty.
• DO NOT insert and remove the
cartridges repeatedly. If you do
so, the ink may seep out of the
cartridge.
■If you mix the colours by installing an ink
cartridge in the wrong position, you must
clean the print head by running several
cleaning cycles after correcting the
cartridge installation. (See “Cleaning the
print head” in chapter 5 Troubleshooting
and Routine Maintenance of the User’s
Guide.)
■Once you open an ink cartridge, install it in
the machine and use it up within six
months of installation. Use unopened ink
cartridges by the expiration date written
on the cartridge package.

8
Setting Up the Machine
1After the cleaning cycle is finished, the LCD
shows:
2Make sure the paper is loaded in the paper
tray.
Press Colour Start.
3The machine starts printing the PRINT
QUALITY CHECK SHEET (only during
initial ink cartridge installation).
Avoid touching the printed surface
of the paper immediately after
printing, the surface may not be
completely dry and may stain your
fingers.
4The LCD shows:
Check the quality of the four colour blocks
formed by the short lines printed on the
sheet.
(BLACK/ CYAN/ YELLOW/ MAGENTA)
5If all lines are clear and visible, press ▲ to
finish the quality check.
---OR---
If you can see missing short lines, press ▼
and go to 6.
6The LCD asks you if the print quality is OK
for black and colour. Press ▲or ▼on the
control panel.
After making your selection ▲(Yes) or ▼
(No) for black and colour, the LCD shows:
Press ▲(Yes), the machine will then start
cleaning the colours.
After cleaning is finished, press
Colour Start. The machine starts printing
the PRINT QUALITY CHECK SHEET again
and goes back to step 3.
7Print Quality Check
Set Paper and
Press Start
Is Quality OK?
▲Yes ▼No
Print Quality Check
1. Check the quality of the four -color blo cks formed by th e short lines.
2. If all th e short lines are clear an d visible, the quality is acceptable. the quality is acceptable.
Select (Yes). If you can see missing short lines, select (No) to begin the co lor cleaning pr ocess
and follow th e prompts on the LCD.
Black OK?
▲Yes ▼No
Start Cleaning?
▲Yes ▼No
OK Poor
Step 1