Brother MFC-6890CDW - Color Inkjet - All-in-One User manual

1
Start Here MFC-6890CDW
Quick Setup Guide
ARL/ASA/NZ Version 0
Before you can use the machine, read this Quick Setup Guide for the correct setup and installation.
1
Unpack the machine and check the components
WARNING
Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep
these bags away from babies and children.
aRemove the protective tape and film covering the machine. Make sure you also remove the film covering
the Touchscreen.
bMake sure you have all components.
WARNING Warnings tell you what to do to prevent possible personal injury.
Important
DO NOT connect the USB cable yet (if you are using a USB
cable).
Ink Cartridges [x4]
Black (LC67HY-BK)
Yellow (LC67HY-Y)
Cyan (LC67HY-C)
Magenta (LC67HY-M)
Quick Setup Guide
User’s Guide CD-ROM
Telephone Line Cord
Telephone Line Cord
Adapter (Australia only)
One Touch Labels
Power Cord
Australia &
New Zealand
Hong Kong,
Malaysia &
Singapore Philippines & Thailand
USB Interface Cable
The supplied mains plug is a
grounded three pin plug.
The supplied mains plug is a
side grounded two pin plug.
Make sure that the AC socket will accept the supplied grounded pin plug. This machine must be grounded, If in doubt, call a
qualified electrician.
Note
• The components included in the box may differ depending on your country.
• Save all packing materials and the box in case for any reason you must ship your machine.
• For a network connection you will need to purchase a network interface cable. Please use the supplied USB
cable for a USB connection.
• To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is
properly grounded through the standard electrical wiring. Non grounded equipment may cause an electrical
shock hazard, and may cause excessive electrical noise radiation.
USB cable
Please make sure you use a USB 2.0 cable (Type A/B) that is no more than 2 metres long.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet Network.

2
2
Load plain A4 paper
aPull paper tray#1 (the upper tray) a
completely out of the machine.
bOpen the paper tray cover a.
cWith both hands, gently press and slide the
paper side guides aand then the paper length
guide bto fit the paper size you are loading in
the tray.
Make sure that the triangular marks con the
paper side guides aand paper length guide b
line up with the mark for the paper size you are
using.
dFan the stack of paper well to avoid paper jams
and misfeeds.
eGently put the paper into paper tray#1 print
side down and top edge first. Check that the
paper is flat in the tray.
fGently adjust the paper side guides to the
paper with both hands. Make sure that the
paper side guides touch the edges of the
paper.
gClose the paper tray cover. Check that the
paper is flat in the tray and below the maximum
paper mark a.
1
1
3
3
2
1
Important
DO NOT push the paper in too far.
1
1

3
hSlowly push the paper tray completely into the
machine.
iWhile holding the paper tray in place, pull out
the paper support auntil it clicks, and then
unfold the paper support flap b.
3
Connect the power cord
and telephone line
aConnect the power cord.
WARNING
The machine must be fitted with an earthed plug.
bConnect the telephone line cord. Connect one
end of the telephone line cord to the socket on
the machine marked LINE and the other end to
a telephone wall socket.
WARNING
Since the machine is grounded through the
power outlet, you can protect yourself from
potentially hazardous electrical conditions on
the telephone network by keeping the power
cord connected to your machine when you
connect it to a telephone line. Similarly, you
can protect yourself when you want to move
your machine by disconnecting the telephone
line first and then the power cord.
Note
For information about tray#2, see Loading paper
in paper tray #2 in Chapter 2 of the User’s Guide.
1
2
Important
DO NOT connect the USB cable yet (if you are
using a USB cable).

4
4
Set Your Country (For
Australia / New Zealand
Customer Only)
You must set your country so that the machine works
correctly on local telecommunication lines in each
country.
aCheck that the power is turned on by
connecting the power cord.
bPress your country.
cThe LCD prompts you to make sure of the
country again.
dIf the LCD shows the correct country, press
Yes to go to the next step.
Or press No to go back to step bto select the
country again.
eAfter the LCD shows Accepted for two
seconds, it shows Please Wait.
Important
The telephone line cord MUST be connected
to the socket on the machine marked LINE.
Note
If you are sharing one telephone line with an
external telephone, connect it as shown below.
1Extension telephone
2External telephone
Note
If you are sharing one telephone line with an
external telephone answering machine, connect it
as shown below.
Set the receive mode to External TAD if
you have an external answering machine.
See Choose a Receive Mode on page 8.
For additional details, see Connecting an
external TAD (telephone answering device)
in Chapter 7 of the User’s Guide.
1
2
(Example for Australia)
(Example for Australia)
Set Country
Set Country
Australia
Newzealand
Australia
Yes No

5
5
Install the ink cartridges
WARNING
If ink gets in your eyes, wash them out with
water at once, and if irritation occurs consult a
doctor.
aMake sure that the power is turned on.
The LCD shows:
bOpen the ink cartridge cover a.
cRemove the green protective part a.
dUnpack the ink cartridge.
eTurn the green knob on the protective yellow
cap clockwise until it clicks to release the
vacuum seal, then remove the cap a.
fTake care to match the colour of the lever a
with the cartridge colour b, as shown in the
diagram below.
gInstall each ink cartridge in the direction of the
arrow on the label.
Note
Do not throw away the green protective part.
You will need it if you transport the machine.
No Cartridge
Install Ink
Black
BK
Cyan
C
Yellow
Y
Magenta
M
1
1
1
1
1
2

6
hGently push the ink cartridge until it clicks. After
all the ink cartridges are installed close the ink
cartridge cover.
Important
After initial installation of the ink cartridges,
the machine will start cleaning the ink tube
system. This cleaning process will last
approximately four minutes.
DO NOT unplug the machine from the power
outlet or attempt to stop the cleaning process.
Interruption of cleaning process may cause
undesired print quality problems.
YC
BK
Important
• DO NOT take out ink cartridges if you do not
need to replace them. If you do so, it may
reduce the ink quantity and the machine will
not know the quantity of ink left in the
cartridge.
• DO NOT shake the ink cartridges. If ink
stains your skin or clothing, wash with soap
or detergent at once.
• DO NOT repeatedly insert and remove the
cartridges. If you do so, ink may seep out of
the cartridge.
• If you mix the colours by installing an ink
cartridge in the wrong position, clean the
print head several times after correcting the
cartridge installation. (See Cleaning the
print head in Appendixes B of the User's
Guide.)
• Once you open an ink cartridge, install it in
the machine and use it up within six months
of installation. Use unopened ink cartridges
by the expiration date written on the
cartridge package.
• DO NOT dismantle or tamper with the ink
cartridge, this can cause the ink to leak out
of the cartridge.
• Brother multifunction machines are
designed to work with ink of a particular
specification and will work to a level of
optimum performance when used with
genuine Brother branded ink cartridges.
Brother cannot guarantee this optimum
performance if ink or ink cartridges of other
specifications are used. Brother does not
therefore recommend the use of cartridges
other than genuine Brother branded
cartridges with this machine or the refilling
of empty cartridges with ink from other
sources. If damage is caused to the print
head or other parts of this machine as a
result of using incompatible products with
this machine, any repairs required as a
result may not be covered by the warranty.

7
6
Check the print quality
aWhen the preparation process has finished, the
LCD shows this message
.
Press Colour Start.
bCheck the quality of the four colour blocks a
on the sheet. (black/yellow/cyan/magenta)
cIf all lines are clear and visible, press Yes to
finish the quality check.
If you can see missing short lines, press No and
go to d.
dThe LCD asks you if the print quality is OK for
black and colour. Press Yes or No.
After pressing Yes or No for both black and
colour, the LCD shows:
ePress Colour Start, the machine will then start
cleaning the colours.
fAfter cleaning is finished, press Colour Start.
The machine starts printing the Print Quality
Check Sheet again. Go back to b.
Important
Make sure you put paper in the upper tray for
the initial setup.
<Black> <Colour>
OK OK
<Black> <Colour>
Poor Poor
Set Paper and Press Start
1
1
Black OK?
Yes No
Start Cleaning?
Press Start

8
7
Choose a Receive Mode
There are four possible receive modes: Fax Only,
Fax/Tel, Manual and External TAD.
aPress MENU.
bPress aor bto display Initial Setup.
cPress Initial Setup.
dPress Receive Mode.
ePress Fax Only, Fax/Tel, External TAD
or Manual.
fPress Stop/Exit.
8
Set the LCD contrast
(If needed)
If you are having difficulty reading the LCD, try
changing the contrast setting.
aPress MENU.
bPress aor bto display General Setup.
cPress General Setup.
dPress aor bto display LCD Settings.
ePress LCD Settings.
fPress LCD Contrast.
gPress Light, Med or Dark.
hPress Stop/Exit.
For details, see Using receive modes in
Chapter 6 of the User's Guide.
Do you want to use the telephone features of your
machine (if available) or an external telephone or
external telephone answering device connected on the
same line as the machine?
Your machine
automatically answers
every call as a fax.
Your machine controls
the line and
automatically answers
every call. If the call is
not a fax, the telephone
will ring for you to pick
up the call.
Your external telephone
answering device (TAD)
automatically answers
every call. Voice
messages are stored
on the external TAD.
Fax messages are
printed.
You control the
telephone line and must
answer every call
yourself.
Do you want the machine to
answer fax and telephone calls
automatically?
Manual
Fax Only
Fax/Tel
External TAD
No
Yes
Yes
No
No
Yes
Are you using the voice message
function of an external telephone
answering device?
Note
You can also adjust the angle of the display by
lifting it.

9
9
Set the date and time
The machine displays the date and time, and if you
set up the station ID, the date and time displayed on
your machine will be printed on every fax you send.
aPress MENU.
bPress aor bto display Initial Setup.
cPress Initial Setup.
dPress Date&Time.
eEnter the last two digits of the year on the
Touchscreen, and then press OK.
(e.g. Enter 09for 2009.)
fRepeat for Month and Day, and Hours and
Minutes in 24-hour format.
gPress Stop/Exit.
10
Enter personal
information (station ID)
You should store your name and fax number to be
printed on all fax pages that you send.
aPress MENU.
bPress aor bto display Initial Setup.
cPress Initial Setup.
dPress Station ID.
eEnter your fax number (up to 20 digits) on the
Touchscreen, and then press OK. For example,
to enter the Australia dialling code “+61”,
press until + appears then enter +.
Press until numbers appear then press 6,
1 and the rest of your number.
fEnter your name (up to 20 characters) using
the Touchscreen, and then press OK.
gPress Stop/Exit.
Year:2009
Ye a r : 2 0 0 9
Date&Time
D a t e & Ti m e
Note
• To enter numbers or special letters, press
repeatedly until the character you want to enter
appears in the character set.
• If you need to enter a character that is on the
same button as the last character, press cto
move the cursor to the right.
• If you entered a letter incorrectly and want to
change it, press dor cto move the cursor to the
incorrect character, press .
Note
If you make a mistake and want to start again,
press Stop/Exit and go back to a.
For details, see Entering Text in Appendix C
of the User's Guide.

10
11
Fax Transmission Report
Your Brother machine is equipped with a
Transmission Verification Report that can be used as
confirmation that you sent a fax. This report lists the
name or fax number of the receiving party, the date,
time, and duration of the transmission, the number of
pages transmitted, and whether or not the
transmission was successful. If you want to use the
Fax Transmission Report feature, see Printing
Reports in Chapter 9 of the User’s Guide.
12
Set tone or pulse dialling
mode (Not available for
New Zealand)
Your machine comes set for Tone dialling service. If
you have Pulse dialling service (rotary), you need to
change the dialling mode.
aPress MENU.
bPress aor bto display Initial Setup.
cPress Initial Setup.
dPress aor bto display Tone/Pulse.
ePress Tone/Pulse.
fPress Pulse (or Tone).
gPress Stop/Exit.