Brother P-touch PT-D600 User manual

Read this User’s Guide before you start using your P-touch.
Keep this User’s Guide in a handy place for future reference.
Please visit us at http://support.brother.com/ where you can get product support and
answers to frequently asked questions (FAQs).
ELECTRONIC LABELING SYSTEM
www.brother.com

INTRODUCTION
Thank you for purchasing the P-touch labeler PT-D600.
Your new P-touch labeler is an easy to operate, feature packed labeling system
that makes creating professional, high quality labels a breeze.
This manual contains various precautions and basic procedures for using this
labeler. Read this manual carefully before using and keep in a handy place for
future reference.
Federal Communications Commission (FCC) Declaration of Conformity
(For USA Only)
Responsible Party : Brother International Corporation
200 Crossing Boulevard
Bridgewater, NJ 08807-0911, U.S.A.
TEL : [phone]
declares, that the products
Product Name : Brother P-touch Electronic Labeling System
Model Number : PT-D600
comply with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Important
• The enclosed interface cable should be used in order to ensure compliance
with the limits for a Class B digital device.
• Changes or modifications not expressly approved by Brother Industries, Ltd.
could void the user’s authority to operate the equipment.

International ENERGY STAR®Compliance Statement
The purpose of the International ENERGY STAR®Program is to
promote the development and popularization of energy-efficient
office equipment. As an ENERGY STAR®Partner, Brother
Industries, Ltd. has determined that this product meets the
ENERGY STAR®guidelines for energy efficiency.
Compilation and Publication Notice
Under the supervision of Brother Industries, Ltd., this manual has been compiled
and published, covering the latest product’s descriptions and specifications.
The contents of this manual and the specifications of this product are subject to
change without notice.
If new versions of the PT-D600 software become available, this manual may not
reflect the updated features. Therefore, you may find that the software and the
contents in this manual are different.
Any trade names and product names of companies appearing on Brother products,
related documents and any other materials are all trademarks or registered
trademarks of those respective companies.
BROTHER is either a trademark or a registered trademark of Brother Industries,
Ltd.

INTRODUCTION
1
Contents
General Description ............................................................................................... 3
Safety Precautions................................................................................................. 4
General Precautions .............................................................................................. 6
GETTING STARTED.................................................................7
Unpacking Your P-touch labeler ............................................................................ 7
LCD Display & Keyboard ....................................................................................... 7
Power Supply and Tape cassette .......................................................................... 9
When using AC adapter (AD-E001) ...............................................................9
When using six new AA alkaline batteries (LR6) or fully charged Ni-MH
batteries (HR6) ............................................................................................... 9
Insert a Tape Cassette ................................................................................. 10
Turning Power On/Off.......................................................................................... 10
Setting Language and Unit .................................................................................. 11
Language...................................................................................................... 11
Unit ............................................................................................................... 11
Turning Tape Color Detection On/Off .................................................................. 11
Feeding Tape....................................................................................................... 11
Feed & Cut ................................................................................................... 11
Feed only...................................................................................................... 12
How to use the P-touch labeler............................................................................ 12
Create a label with the P-touch labeler......................................................... 12
Create a label by connecting your labeler to a PC ....................................... 13
Setting Input Mode............................................................................................... 15
Label View Mode .......................................................................................... 15
Print Preview Mode ...................................................................................... 15
EDITING A LABEL ..................................................................16
Entering and Editing Text .................................................................................... 16
Entering Text from the Keyboard..................................................................16
Adding a New Line ....................................................................................... 16
Adding a New Block ..................................................................................... 16
Deleting Text ................................................................................................ 16
Inserting a Tab.............................................................................................. 17
Using Text Reminder.................................................................................... 17
Deleting Text Reminder Memory.................................................................. 18
Changing Text Reminder Setting ................................................................. 18
Entering Accented Characters............................................................................. 18
Setting Character Attributes ([Font]/[Size]/[Width]/[Style]/[Line]/[Align]) .............. 19
Setting Character Attributes by Label...........................................................19
Setting Character Attributes by Each Line.................................................... 19
Setting Auto Fit Style .................................................................................... 21
Setting Frames .................................................................................................... 21
Entering Symbols................................................................................................. 23

INTRODUCTION
2
Entering Symbols Using the Symbol Function ............................................. 23
Setting Symbol History ................................................................................. 23
Setting Label Attributes ([Length]/[Cut Option]/[Tab Length])..............................24
Using Auto-Format Layouts ................................................................................. 25
Using Templates........................................................................................... 25
Using Block Layouts ..................................................................................... 29
Using Table Format ...................................................................................... 32
Printing Transferred Labels (For Windows®)................................................ 33
Creating a Bar Code Label .................................................................................. 34
Setting Bar Code Parameters and Entering Bar Code Data ........................34
Editing and Deleting a Bar Code .................................................................. 36
Using Time & Date Function ................................................................................ 37
Clock Setting ................................................................................................ 37
Time & Date Format Setting ......................................................................... 37
Time Stamp Setting ...................................................................................... 38
Changing and Deleting the Time & Date Settings ........................................ 40
LABEL PRINTING ...................................................................41
Previewing Labels................................................................................................ 41
Printing Labels ..................................................................................................... 41
Single and Multiple Copy Printing................................................................. 41
Numbering Printing....................................................................................... 42
Mirror Printing ............................................................................................... 42
Setting Tape Cutting Options............................................................................... 42
[Large Margin]/[Small Margin]/[Chain]/[No Cut]/[Special tape] ..................... 42
Adjusting the Label Length .................................................................................. 44
Printing from the Label Collection........................................................................ 44
Printing a label from the label collection stored in the P-touch labeler......... 44
Downloading a new Label Collection Category ............................................45
USING THE FILE MEMORY ...................................................46
Saving Label Files ............................................................................................... 46
Printing, Opening, Deleting, or Marking a Saved Label....................................... 46
[Print] ............................................................................................................ 46
[Open]........................................................................................................... 46
[Delete] ......................................................................................................... 46
[Marking]....................................................................................................... 47
RESETTING & MAINTAINING YOUR P-TOUCH LABELER..48
Resetting the P-touch Labeler ............................................................................. 48
Resetting the Data Using the home key ....................................................... 48
Resetting the Data to Factory Settings Using the P-touch Labeler
Keyboard ...................................................................................................... 48
Maintenance ........................................................................................................ 49
Cleaning the Unit .......................................................................................... 49
Cleaning the Print Head ............................................................................... 50
Cleaning the Tape Cutter ............................................................................. 50

INTRODUCTION
3
General Description
TROUBLESHOOTING ............................................................51
What to do when.................................................................................................. 51
When an error message appears on the display .................................................52
APPENDIX ..............................................................................53
Specifications....................................................................................................... 53
System Requirements ......................................................................................... 54
General Description
Tape cassette compartment cover
Tape viewer
LCD display
Tape exit slot Print head
Keyboard
Tape cassette compartment
Tape cutter Release lever
Battery compartment cover
USB port
AC adapter jack
Battery compartment

INTRODUCTION
4
Safety Precautions
Safety Precautions
To prevent injury and damage, important notes are explained using various
symbols. The symbols and their meanings are as follows:
The symbols used in this manual are as follows:
WARNING Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injuries.
CAUTION Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injuries.
Action NOT allowed DO NOT touch a given portion of
the product.
Mandatory action Unplugging is required
DO NOT disassemble the product. Alerts to the possibility of
electrical shock
WARNING
Follow these guidelines to avoid the risk of fire, burns, injury, electric shocks,
rupture, overheating, abnormal odors or smoke.
Always use the specified voltage
and the suggested AC adapter
(AD-E001) for the P-touch labeler
to prevent any damage or failure.
Do not touch the AC adapter and
P-touch labeler during a thunder
storm.
Do not use the P-touch labeler/AC
adapter in places of high humidity
such as bathrooms.
Do not place heavy objects on, or
damage the power cord or plug. Do
not forcibly bend or pull the power
cord. Always hold the AC adapter
when disconnecting from the
power outlet.
Make sure that the plug is fully
inserted to the power outlet. Do not
use an outlet that is loose.
Do not allow the P-touch labeler/
AC adapter/power plug/batteries to
get wet, for example, by handling
them with wet hands or spilling
beverages on to them.
Since loss of eyesight may result
when leaked fluid from batteries
gets into your eyes, immediately
rinse your eyes with a large amount
of clean water, and then seek
medical attention.
Do not disassemble or modify the
P-touch labeler/AC adapter/
batteries.
Do not allow a metal object to
contact both the plus and minus
ends of a battery.
Do not use sharp objects, such as
tweezers or a metallic pen, to
change the batteries.
Do not throw the batteries into fire
or expose to heat.
Disconnect the AC adapter and
remove batteries immediately and
stop using the P-touch labeler if
you notice abnormal odor, heat,
discoloration, deformation or
anything unusual while using or
storing it.

INTRODUCTION
5
Safety Precautions
Do not use a damaged or leaking
battery as the fluid may get on your
hands.
Do not use a deformed or leaking
battery or one whose label is
damaged. There is a possibility of
generating heat.
Do not touch metal parts around
the print head immediately after
printing.
When the P-touch labeler is not
being used, store it out of the reach
of children. In addition, do not allow
children to put the P-touch labeler
parts or labels in their mouths. If
any object has been swallowed,
seek medical attention.
Do not use a damaged adapter
cord or power plug.
Do not use the P-touch labeler
when a foreign object enters the
P-touch labeler. If any foreign
object enters the P-touch labeler,
disconnect the AC adapter and
remove the batteries, and contact
Brother customer service.
DO NOT touch the blade of the
cutter unit.
CAUTION
Follow these guidelines to avoid personal injury, liquid leakage, burns or heat.
If leaked fluid from batteries gets on
your skin or clothes, immediately
rinse them with clean water.
Remove the batteries and
disconnect the AC adapter if you do
not intend to use the P-touch
labeler.
Do not use a battery other than that
specified. Do not use combinations
of old and new batteries or
combinations of different types,
different charging levels, different
manufacturers or different models.
Do not insert a battery with the
polarity (+ and -) reversed.
Do not drop or hit the P-touch
labeler/AC adapter.
Do not press on the LCD display.
Do not put your finger inside the
P-touch labeler when you close the
tape cassette compartment cover
or battery compartment cover.
Before using Ni-MH rechargeable
batteries, carefully read the
instructions for the batteries and
battery charger, and be sure to use
them correctly.
When using Ni-MH rechargeable
batteries, charge the batteries with
a specialized battery charger
before using the batteries.
DO NOT open the tape cassette
compartment cover when
operating the cutter unit.
DO NOT apply excessive pressure
to the cutter unit.
WARNING

INTRODUCTION
6
General Precautions
General Precautions
• Depending on the location, material, and environmental conditions, the label may
unpeel or become irremovable, the color of the label may change or be
transferred to other objects. Before applying the label, check the environmental
conditions and the material.
• Do not use the P-touch labeler in any way or for any purpose not described in this
guide. Doing so may result in accidents or damage the P-touch labeler.
• Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not
have the mark.
• Only use a soft, dry cloth to clean the labeler; never use alcohol or other organic
solvents.
• Use a soft wipe to clean the print head; never touch the print head.
• Do not put any foreign objects into the tape exit slot, AC adapter connector or
USB port, etc.
• Do not place the P-touch labeler/batteries/AC adapter in direct sunlight or rain,
near heaters or other hot appliances, in any location exposed to extremely high
or low temperatures (e.g., on the dashboard or in the back of your car) or high
humidity, or in dusty locations.
• Do not try to print if the cassette is empty; it will damage the print head.
• Do not pull the tape while printing or feeding; it will damage the tape and the
P-touch labeler.
• It is recommended that you use the USB cable supplied with the P-touch labeler.
Should another USB cable need to be used, ensure it is of high quality
construction.
• Any data saved in memory will be lost due to failure or repair of the P-touch
labeler, or if the battery expires.
• The P-touch labeler is not equipped with a charging feature for rechargeable
batteries.
• The printed text may differ from the text that appears in the LCD.
• The length of the printed label may differ from the displayed label length.
• When power is disconnected for two minutes, all text, format settings and any text
files saved in the memory will be cleared.
• You can also use Heat Shrink Tube in this model. Check the Brother website
(http://www.brother.com/) for further information. You cannot print frames,
pre-set P-touch templates, or use certain font settings when using Heat Shrink
Tube. Printed characters may also be smaller than when using TZe tape.
• Be sure to read the instructions provided with Fabric Iron-On Tapes, Extra
Strength Adhesive Tapes or other special tapes and observe all precautions
noted in the instructions.
•A protective clear plastic sticker is placed over the display during
manufacturing and shipping. This sticker should be removed prior to use.

7
Unpacking Your P-touch labeler
GETTING STARTED
Unpacking Your P-touch labeler
LCD Display & Keyboard
Carton Contents
P-touch labeler
Starter Tape Cassette
AC adapter
USB Cable
User’s Guide
8113
11
9
87123456
11 12
10
Print Preview Mode Label View Mode
16 17 18 19 20 21
29 28 27 26 25
22
23
24
15
14
33
32
31
30
The default language is [English].

GETTING STARTED
8
LCD Display & Keyboard
NOTE
• When the caps mode is on, all characters you type will be in
uppercase letters.
• Use ( ) in combination with the letter and number keys to type
uppercase letters or the symbols indicated on the upper-right corner
of the keys.
• Use or with ( ) to go to the beginning of the previous or next
block.
• Use or with ( ) to go to the beginning or end of the current
line.
• While selecting the settings, press ( ) to go back to the default
item.
• Unless otherwise mentioned, press ( ) to cancel any operation.
• Press ( ) to return to the home screen.
• Label length shown on LCD may slightly differ from the actual label
length when printed.
1. Caps mode
2-7. Style guidance
8. Tape width x Label length
9. Block number
10. Line number
11. Cursor
12. Return mark
13. Zoom
14. Power
15. Home
16. Clear
17. Escape
18. Cursor
19. OK
20. Function
21. Preview
22. Print
23. Backspace
24. Shift
25. Enter
26. Accent
27. Space
28. Symbol
29. Scale/Zoom
30. Shift
31. Caps
32. Tab
33. Letter

9
Power Supply and Tape cassette
GETTING STARTED
Power Supply and Tape cassette
When using AC adapter (AD-E001)
Insert the plug on the adapter cord into the AC adapter jack on the side
of the machine. Insert the plug into the nearest standard electrical outlet.
When using six new AA alkaline batteries (LR6) or fully charged
Ni-MH batteries (HR6)
Make sure that their poles point in the correct directions.
To remove the batteries, reverse the installation procedure.
NOTE
• For memory back up, we recommend using AA alkaline batteries
(LR6) or Ni-MH batteries (HR6) together when using the AC adapter.
• To safeguard and backup the P-touch labeler’s memory, when the
AC adapter is unplugged it is recommended to have AA alkaline
batteries (LR6) or Ni-MH batteries (HR6) installed in the P-touch
labeler.
• When power is disconnected for more than two minutes, all text and
format settings will be cleared. Any text files saved in the memory will
also be cleared.
• Remove the batteries if you do not intend to use the P-touch labeler
for an extended period of time.
• Dispose of the battery at an appropriate collection point, not in the
general waste stream. In addition, be sure to observe all applicable
federal, state, and local regulations.

GETTING STARTED
10
Turning Power On/Off
• When storing or discarding the battery, wrap it (for example with
cellophane tape), to prevent it from short-circuiting.
(Battery insulation example)
1. Cellophane tape
2. Alkaline or Ni-MH battery
Insert a Tape Cassette
NOTE
• When inserting the tape cassette, make sure that the tape and ink
ribbon do not catch on the print head.
• If you cannot close the tape cassette compartment cover, check to
ensure the release lever is in the up position. If not, lift the lever, and
then close the cover.
Turning Power On/Off
Press ( ) to turn the P-touch labeler on.
Press ( ) again to turn the P-touch labeler off.
NOTE
Your P-touch labeler has a power saving function that automatically
turns itself off if no key is pressed within a certain time under certain
operating conditions. Refer to “Specifications” on page 53.
1
2
CAUTION
USING A COMBINATION OF DIFFERENT BATTERIES (SUCH AS Ni-MH AND
ALKALINE), MAY RESULT IN AN EXPLOSION. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.

11
Setting Language and Unit
GETTING STARTED
Setting Language and Unit
Language
When you turn on the P-touch labeler for the first time, you are asked to
set the default language. Select language using or , and then press
()or( ).
Unit
The default setting is [inch].
Turning Tape Color Detection On/Off
When using the label view mode, if tape color detection is set to [On], the
P-touch labeler detects the color of the tape cassette and displays the
label image on the LCD screen according to the color of the tape
cassette. This enables you to display a more accurate preview of the
label that you are creating. The default setting is [On].
NOTE
Depending on the tape cassette you are using, the P-touch cannot
detect the color of the tape cassette. In this case, the label image on
the LCD screen is displayed as black text on a white background.
Feeding Tape
Feed & Cut
To feed and cut the tape, press the following keys:
()Î/ [Settings] Î()or( )Î/ [ Language] Î()or
()
Î/ [English/Español/Français/Hrvatski/Italiano/Magyar/
Nederlands/Norsk/Polski/Português/Português(Brasil)/Română/Slovenski/
Slovenský/Suomi/Svenska/Türkçe/Čeština/Dansk/Deutsch] Î( ) or ( ).
()Î/ [Settings] Î()or( )Î/ [Unit] Î( ) or ( )
Î/ [inch/mm] Î()or( ).
()Î/ [Settings] Î()or( )Î/ [Tape Color] Î()or
()
Î/ [On/Off] Î()or( ).
()+()Î/ [Feed & Cut] Î( ) or ( ).

GETTING STARTED
12
How to use the P-touch labeler
Feed only
To feed the tape, press the following keys:
NOTE
Feed Only function is recommended when using Fabric Iron-On
Tapes, which should be cut using scissors.
How to use the P-touch labeler
Create a label with the P-touch labeler
[GETTING STARTED]
[CREATING A LABEL]
NOTE
In addition to entering text, the P-touch labeler has a large range of
formatting options.
Examples of labels you can create using the P-touch labeler:
[LABEL PRINTING]
()+()Î/ [Feed Only] Î()or( ).
Preparing the P-touch labeler P. 7
• Entering and Editing text
• Entering Symbols
• Entering Accented Characters
• Using Auto-Format Layouts
P. 16
P. 23
P. 18
P. 25
• Printing a label
• Setting Tape Cutting Options
• Printing from the Label Collection
P. 41
P. 42
P. 44

13
How to use the P-touch labeler
GETTING STARTED
NOTE
Before printing, you can check the layout of your label using the
preview function.
Refer to “Previewing Labels” on page 41.
Example of the preview screen:
Create a label by connecting your labeler to a PC
[GETTING STARTED]
This labeler can be connected to a PC/Mac and used with the P-touch
Editor software to create more elaborate labels. To use your labeler
connected to a computer, attach your labeler to a computer via the
included USB cable and install the P-touch Editor software and drivers.
Features
P-touch Editor Makes it easy for anyone to create a wide variety of
custom labels in complex layouts by using fonts,
templates, and clip art.
Printer Driver Lets you print labels from the connected P-touch
labeler when using P-touch Editor on your computer.
P-touch Update Software Label collections can be downloaded and new label
designs added to the P-touch labeler.
In addition, the software can be upgraded to the
latest version.
P-touch Transfer Manager
(Windows®only)
Allows you to transfer up to 9 label templates to the
P-touch labeler and save backups of your data on
the computer.
Installer download website
• A CD-ROM is not included with this product.
• To download and install printer drivers and software such as the P-touch Editor
5.1 on your computer, visit our installer download website
(www.brother.com/inst/).

GETTING STARTED
14
How to use the P-touch labeler
Printer drivers and software are also available to download individually
from the list of available printer drivers and software on our support
website below:
[CREATING A LABEL]
Brother support website
Please visit our support website at http://support.brother.com/.
You can find following information:
• Software downloads
• Manuals/Documents
• Frequently Asked Questions (Troubleshooting, Useful tips on using printer)
• Consumable information
• Latest OS compatibility information
The contents of this website are subject to change without notice.
• Connect the P-touch labeler to your computer with the included USB cable.
• Launch the P-touch Editor Software.
• Enter the label text using P-touch Editor.
• Print the label.
Examples of labels you can create using the P-touch Editor:

15
Setting Input Mode
GETTING STARTED
Setting Input Mode
The default setting is [Label View].
Label View Mode
The character attributes and frames, etc. that you set are reflected on the
LCD screen while creating a label. This enables you to easily check what
the label will look like.
Example:
NOTE
You can press ( ) to change the magnification of the LCD screen.
This enables you to switch to a magnification that is comfortable for
creating labels.
Print Preview Mode
The character attributes and frames, etc. that you set are not reflected
on the LCD screen while creating a label. You can check what the label
will look like using the preview function. Refer to “Previewing Labels” on
page 41.
Example:
()Î/ [Settings] Î()or( )Î/ [Input Mode] Î()or
()
Î/ [Label View] Î()or( ).
()Î/ [Settings] Î()or( )Î/ [Input Mode] Î()or
()
Î/ [Print Preview] Î( ) or ( ).

16
Entering and Editing Text
EDITING A LABEL
Entering and Editing Text
Entering Text from the Keyboard
Adding a New Line
Move the cursor to end of the current line and press ( ).
NOTE
• There is a maximum number of lines of text that can be entered for
each tape width. A maximum of 7 lines for 0.94" (24 mm) tape, 5 lines
for 0.70" (18 mm) tape, 3 lines for 0.47" (12 mm) tape, 2 lines for 0.35"
(9 mm) and 0.23" (6 mm) tape, and 1 line for 0.13" (3.5 mm) tape.
• When [Input Mode] is set to [Label View], if you press ( ) to add
a new line and there is already a maximum number of lines of text that
can be entered for the tape you are using, [Too Many Lines!] is
displayed. When [Input Mode] is set to [Print Preview], if you press
( ) and seven lines already exist, [Too Many Lines!] is displayed.
Press ( ) or any other key to clear the error message.
Adding a New Block
To create a new block of text/lines to the right of your current text, press
( ) and ( ). The cursor moves to the start of the new block.
NOTE
• A maximum of 5 blocks can be entered in one label.
• If you press ( ) and ( ) when five blocks already exist, [Too
Many Blocks!] is displayed. Press ( ) or any other key to clear the
error message.
Deleting Text
By pressing ( ), the letters will be deleted one by one.
To delete all text:
()Î/ [Create Label] Î()or( )ÎEnter the character.
Line 1 Line 2 Label image
()Î/ [Text Only] Î( ) or ( ).

17
Entering and Editing Text
EDITING A LABEL
To delete all text and format settings:
Inserting a Tab
To insert a tab, press the following key.
When using the print preview mode, the symbol ( ) will then appear on
the screen.
NOTE
To delete a tab from a label, position the cursor to the right of the tab
mark on the text entry screen and press ( ).
To change tab length:
NOTE
You can also set the tab length by typing in the desired tab length. To
apply the setting, after typing in the tab length, press ()or ( )
and then ()or ( ) again.
Using Text Reminder
When a character is entered, the P-touch labeler remembers character
sequences beginning with the character entered from a history of all
printed character sequences to date, and displays a list of options from
which to select. The default setting is [On].
Example:
()Î/ [Text&Format] Î( ) or ( ).
().
()Î/ [Tab Length] Î( ) or ( ) Î/ [0.0" - 4.0"
(0 - 100 mm)] Î( ) or ( ) Î( ) to return to the text entry screen.
Enter “B” Î()ÎThe P-touch labeler displays a list of words printed beginning
with the letter “B” such as “Brother” Î/ Select the desired word ÎPress
to display the entire word that is too long to display on the list of words. To
return to the list of words, press ÎPress ( ) or ( ), the selected
character word will then appear on the text line.