BTC KAMAMI ZL10PLD User manual

dipPLD module
with XC3S200 device
ZL10PLD
ver. 1.0
The dipPLD modules are designed to helps
using of Spartan 3 FPGA devices by people
that can’t use automatic assembly of QFP
packages.

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device
Key features
► XC3S200 Spartan 3 FPGA device in VQFP100 package (equivalent for 200000 logic gates, 12 hardware mul-
tipliers, 4 frequency multipliers, 216kb of Block SRAM)
► flash configuration memory size: 1Mb (XCF01S)
► 61 I/O lines (including five 5V-tolerant input lines)
► built-in LVC/LCX inverters for buffering 6 I/O lines
► switch for manual configuring FPGA
► LED indicating correctly configured FPGA
► JTAG interface (ZL11PRG, ZL11PRG-M or ZL4PRG)
► quartz generator 3.6864 MHz
► built-in voltage regulators: 1.2/2.5 and 3.3V
► 4.4–7VDC power supply
► current consumption: 110mA (depend on frequency)
► ready to use with ZL9PLD base board
For ZL10PLD dipPLD module are available free PCB and SCH libraries for Protel99SE and Protel
DXP. They can be downloaded from: http://www.kamami.pl/dl/zl10pld_libs.zip
Code Description
ZL10PLD
► Assembled module with XC3S200-VQG100 device
Standard equipment
Disclaimer
BTC Korporacja makes no warranty for the use of its products and assumes no responsibility for any errors which may appear in this document nor does it make a commitment to update the information contained herein.
BTC Korporacja products are not intended for use in medical, life saving or life sustaining applications.
BTC Korporacja retains the right to make changes to these specifications at any time, without notice.
All product names referenced herein are trademarks of their respective companies.
Technical assistance
For technical assistance, please contact [email protected].
Please provide the following data:
► Version of the operating system
► Microcontroller type used in your system and its oscillator frequency
► Detailed description of the problem
BTC Korporacja
05-120 Legionowo, Poland
ul. Lwowska 5
e-mail: offi[email protected]
http://www.kamami.com
ZL10PLD module works with ZL9PLD base board.

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device 3
Module configuration
Electrical schematic of ZL10PLD is shown in the below picture.

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device
4
!I/O line of ZL10PLD are compatible only with 3.3V logic! It does not concern five selected lines
which are equipped with voltage buffers LVC/LCX.
Module pins
!I/O line, marked by „p36” symbol, is an input of clock signal (turned in the stage of quartz generator
which is installed on ZL10PLD ). It can be used only as an output to the cooperation with devices
which are powered by 3.3V voltage.
Arrangement of the most important module

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device 5
JTAG connector
ZL10PLD module is equipped with IDC connector, for connecting ISP programmer (for example: ZL11PRG,
ZL11PRG-M, ZL4PRG). Placement of this connector on the board and signals arrangement are shown in the below
pictures.
FPGA device and configuration memory (Flash memory U2) are connected to a JTAG chain, as in the below pic-
ture. This connection enables independent Flash memory programming and configuring of FPGA device with the
use of programmer which is in accordance with Xilinx DLC III programmer (for example: ZL11PRG, ZL4PRG).
FPGA configuration mode selection
FPGA device, after turning on voltage, can be automatically configured (configuration is copied from Flash confi-
guration memory) or can wait for configuration data which are supplied by the user with the use of JTAG interface.
The choice of configuration mode takes place with the use of JP4 connector, according to the description, placed
on the printed board.

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device
6
FPGA manual reconfiguration switch
With the use of placed on the board button (its placement is shown in the below picture) the user in any moment
can restore FPGA configuration which is saved in the memory. The correct FPGA configuration is indicated by
RDY LED.
Quartz generator
ZL10 PLD is equipped with quartz generator with 3.6864MHz output frequency and 5V power supply voltage.
Thanks owing to the fact that the quartz generator is placed in the socket, the user can exchange it for any other,
useful in application testing.

http://www.kamami.com/
ZL10PLD – dipPLD module with XC3S200 device 7
ZL9PLD base board peripherals connection
The ZL10PLD module is adapted to cooperation with ZL9PLD base board. On picture below is shown way of
connection to module peripherals from ZL9PLD base board.