Buhl PLC4418E User manual

( Instructions continued on next page )
Page 1
Parts list
Qty. Description
1 Top shelf with decal
1 Middle shelf
1 Bottom shelf
2 Legs (Labeled "O")
2 Legs (Labeled "X")
2 Horizontal mount
3 Set Screws and serrated nuts (E)
1 Electrical bracket
1 Power cord
1 Handle (Optional)
Qty. Description
25 Set Square head bolts, washer and serrated nuts (I)
2 Casters with brakes
2 Casters without brakes
2 Security screw (G)
2 Hex head screw (H)
2 Pole for supporting flat panel TV
2 Security screw for mounting the pole (F)
4 Set Screws and serrated nuts for pull out shelf (J)
1 Set Side extended pull out shelf
Tools required
Hex wrench
L key
Adjustable wrench/pliers
Rubber mallet
PLC4418E
Screw table
1.
Lay front legs (labeled "O" and "X") on the floor with the brackets
facing upward and inward as illustrated. Note: legs,when placed
on the floor should bend upward, off the floor at their top end and
the width of the unit should remain constant all the way to the top.
2.
Slide each shelf over the brackets of the legs. The largest shelf is
the bottom. The top shelf has the Buhl decal on it.
3.
Slide the two remaining legs onto the shelves as illustrated. Make
sure that the brackets are inside the shelves.
4.
HAND TIGHTEN the top, middle and bottom shelves at the two
corners with square head bolt, washer and nut (see screw table I)
as illustrated. Please make sure washer and nut are together on
the inside of the leg bracket.
Instruction sheet -- Buhl Flat panel TV cart
Model number: PLC4418E
Congratulations for having chosen this excellent Buhl product.
To assure your complete satisfaction, this product is warranted against defect in
manufacture for one year after the purchase date. Any parts requiring replacement
during the 1--year period, under normal use and service, as a result of defective
workmanship, will be replaced by Buhl or by an authorized Buhl dealer, without cost,
except for transportation charges. All unit should be returnd in original packing to
guarantee safe transport. Buhl is not responsible for damage in shipment.
Some screws may have already
screwed on the related parts.
Pole Horizontal mount
Note: This unit is easier to assemble with two people.
"X"
"O"

A Division of Vcom MM Corp.
South Hackensack, NJ 07606, USA
Tel.:[phone]
If any parts or hardware are missing or damaged, Do Not
Return the unit to your dealer. Call the Buhl helpline at
[phone] for immediate parts replacement.
5.
In order to have the unit properly
aligned, stand unit upright on a
level surface. Gently rock unit
back and forth to realign and
level the unit.TIGHTEN ALL
NUTS AND BOLTS WITH
WRENCHES AT THIS TIME.
Unit should now be properly
aligned and level. If unit is not
level at this time, repeat the
above steps before proceeding
to step 6.
6.
Lay unit on floor.
Insert casters
with brakes into
opposite corner
holes on the
bottom of the
unit as shown.
Insert the other
casters into the
remaining holes.
7.
Insert the two supporting poles onto the holes on top shelf. Wire
holes face inside.
8.
Insert the two horizontal
mounts onto the supporting
poles. Note: The mount with
adjustable screw(see screw
table H) should go on the
bottom. Screw(see screw
table G) the top mount to
desired height from Ato F.
Adjust the bottom mount
height according to the TV
screw position as shown.
9.
Tighten the two supporting poles onto the top shelf with two
security screws as shown (see screw table F).
10.
Electrical bracket assembly instruction
A. Push power cord into cord winder bracket.
B. Attach electrical bracket to back side of top shelf with two nuts
and bolts(see screw table E). Tighten nuts and bolts securely.
Wrap power cord around wings of the bracket.
11.
Use the appropriate security screw needed (M4, M5, M6 or M8,
see screw table A,B,C or D) to fasten the flat panel TV onto the
horizontal mounts as shown.
Page 2
12.
Handle assembly instruction ( Optional )
A. Unscrew the scews from the handle.
B. Attach the handle to the top shelf (either side) and tighten
handle to the shelf with screws from the inside under the shelf
as shown.
13.
Side extended pull out shelf assembly instruction
Adjust the length of the pull out
shelf as shown on Fig. A by
loosing the screws and
tightening again so that the
width of the pull out shelf
matches the width of the
cart. Tighten the pull out
shelf to the cart with the
screw (see screw table J)
as shown on Fig. A and
Fig. B.
14.
To return the pull out
shelf inside the cart
when not in use, push
and hold the locking
mechanism down as
shown.
Top horizontal mount
Bottom horizontal mount