Buhl PLCAB44E User manual

Instruction sheet -- Buhl Flat panel TV cart
Model number: PLCAB44E
Congratulations for having chosen this excellent Buhl product.
To assure your complete satisfaction, this product is warranted against defect in
manufacture for one years after the purchase date. Any parts requiring replacement
during the 1--year period, under normal use and service, as a result of defective
workmanship, will be replaced by Buhl or by an authorized Buhl dealer, without cost,
except for transportation charges. All unit should be returnd in original packing, to
guarantee safe transport.
Buhl is not responsible for damage in shipment. If you have
any questions regarding the assembly of your table, please call the
Buhl helpline at
[phone] 9:00 am - 4:00pm eastern time.
Note: This unit is easier to assemble with two people.
Parts list PLCAB44E
Page 1
Qty. Description
1 Top shelf with decal
1 Middle shelf
1 Bottom shelf
1 Cabinet shelf
2 Legs(Labeled "O")
2 Legs(Labeled "X")
2 Side panels
1 Rear panel
Qty. Description
1 Right door assembly
1 Left door assembly
1 Pull-out shelf (set)
2 Casters with brakes
2 Casters without brakes
1 Electrical bracket
1 Power cord
4 Shelf support
Qty. Description
25 Set Square head bolts,washer and serrated nuts(I)
25 Set Machine screws and washer (K)
3 Set Screws and hex nuts(E)
2 Hex head screws for mounting the poles
2 Poles for supporting flat panel TV
2 Horizontal mount
2 Vertical mount
Tools required
Hex wrench (provided)
Allen key (provided)
Adjustable wrench/pliers
Rubber mallet
Pole Horizontal mount Vertical mount

1.
Lay front legs (labeled "O" and "X") on the floor with the brackets
facing upward and inward as illustrated. Note: legs,when placed
on the floor should bend upward, off the floor at their top end and
the width of the unit should remain constant all the way to the top.
2.
Slide each shelf over the brackets of the legs.The top shelf has
the buhl decal on it. The larger shelves are on the bottom. The
shelf with wire hole is the middle shelf. Please make sure the
locking mechanism facing the same direction on middle and
bottom shelves.
3.
Slide the two remaining legs onto the shelves as illustrated.
Make sure that the brackets are on the inside of the shelves.
4.
HAND TIGHTEN the top, middle and bottom shelves at the two
corners on top with square bolt, washer and nut (see screw table
I) as illustrated. Please make sure washer and nut are together
on the inside of the leg bracket.
5.
In order to have the unit
properly aligned, stand
unit upright on a level
surface. Gently rock unit
back and forth to realign
and level the unit.
TIGHTEN ALL NUTS AND
BOLTS WITH WRENCHES
AT THIS TIME. Unit should
now be properly aligned
and level. If unit is not level
at this time, repeat the
above steps before
proceeding to step 6.
6.
Slide the back panel between the middle and bottom shelf. The
bottom of the back panel needs to hook onto the bottom frame
lip and the top of the panel needs to go in between middle shelf
lip and the brackets.
7.
Lay unit on floor. Insert
casters with brakes
into opposite corner
holes on the bottom of
the unit as shown.
Insert the other casters
into the remaining
holes.
8.
To secure the cabinet panel, use the machine screws(see screw
table K) to tighten the cabinet panels to the frame poles as shown.
There are three screws on each side.
( Instructions continued on next page )
Page 2

Page 3
A Division of Vcom MM Corp.
South Hackensack, NJ 07606, USA
Tel.:[phone]
If any parts or hardware are missing or damaged, Do Not
Return the unit to your dealer. Call the Buhl helpline at
[phone] for immediate parts replacement.
9.
Insert shelf support to desired height as shown. Put the cabinet
shelf on top of the shelf supports. Install the two doors onto the
frame with three machine screws(see screw table K) on each side.
Do not tighten completely at this time. Adjust the doors to make
sure they close and lock OK. Tighten all screws.
10.
Insert the two supporting poles onto the holes on top shelf.
Wire holes can face inside or outside.
11.
Insert the two horizontal
mounts onto the supporting
poles. Note: The mount with
adjustable screw(see screw
table H) should go on the
bottom. Screw(see screw
table G) the top mount to
desired height from A to F.
Adjust the bottom mount
height according to the TV
screw position as shown.
12.
Tighten the two supporting poles onto the top shelf with two hex
head screws (see screw table F) as shown on Fig. 1. Tighten the
four pull out shelf support brackets (see screw table J) onto the
poles as shown on Fig. 2.
Top horizontal mount
Bottom horizontal mount
Fig. 1
Fig. 2
13.
Tighten the pull out shelf onto the support bracket as shown (see
screw table J). Note: Adjust the pull out shelf forward and
sideward to make sure they pull out smoothly before
tightening the screws.
14.
Electrical bracket assembly
A. Push power cord into cord winder bracket.
B. Attach electrical bracket to back side of top shelf with two nuts
and bolts(see screw table E). Tighten nuts and bolts securely.
Wrap power cord around wings of the bracket.
15.
Use the appropriate bolts needed (M4, M5, M6 or M8, see
screw table A,B,C and D) to fasten the flat panel TV onto the
horizontal mounts as shown.
16.
In case the flat panel TV cannot be mounted onto the horizontal
mounts because of the hole position differences, use the vertical
mounts instead. Mount the vertical mounts onto horizontal mounts
according to the TV screw positions. Then mount the TV onto
vertical mounts as shown.