Burcam 300910 User manual

2190 Boul. Dagenais West TEL: [phone]
LAVAL (QUEBEC) FAX: [phone]
CANADA
H7L 5X9 [email protected]
INSTALLATION
INSTRUCTIONS
MODEL
300910
FOUNTAIN &
WATERFALLS
PUMP
Please read these
instructions
carefully. Failure
to comply to
instructions and
designed
operation of
this system,
may void the
warranty.
Your pump has been
carefully packaged at
the factory to prevent
damage during shipping.
However, occasional
damage may occur due to
rough handling. Carefully
inspect your pump for
damages that could
cause failures. Report
any damage to your
carrier or your point of
purchase.
WWW.BURCAM.COM
© 2010 BUR-CAM Printed in Canada 310136

FOR INFORMATION TEL: [phone] FAX: [phone]
SAFETY INSTRUCTIONS:
This fine pump that you have just purchased is designed from the latest in material and
workmanship.
Before installation and operation, we recommend the following procedures:
CHECK WITH YOUR LOCAL ELECTRICAL AND PLUMBING CODES TO
ENSURE YOU COMPLY WITH THE REGULATIONS. THESE CODES HAVE
BEEN DESIGNED WITH YOUR SAFETY IN MIND. BE SURE YOU COMPLY
WITH THEM.
WE RECOMMEND THATA SEPARATE CIRCUIT BE LEAD FROM THE HOME
ELECTRICAL DISTRIBUTION PANEL PROPERLY PROTECTED WITH A
FUSE OR A CIRCUIT BREAKER. WE ALSO RECOMMEND THAT A GROUND
FAULT CIRCUIT BE USED. CONSULT A LICENSED ELECTRICIAN FOR ALL
WIRING.
THE GROUND TERMINALON THETHREE PRONG PLUGS SHOULD NEVER
BE REMOVED. THEY ARE SUPPLIED AND DESIGNED FOR YOUR
PROTECTION.
NEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR
PRODUCT WITH THE POWER CONNECTED. DO NOT ONLY UNSCREW
THE FUSE OR TRIP THE BREAKER, REMOVE THE POWER PLUG FROM
THE RECEPTACLE.
A
B
C
D
2
APPLICATION
This submersible utility pump is designed for
a permanent application at home.
May also be used for waterfall, fountain.
May also be used for a portable application
like water transfer.
CAPACITY:
5’ 4000 USGPH 1.5m 15100 LPH
10’ 3400 USGPH 3.0m 12900 LPH
15’ 2600 USGPH 4.5m 9800 LPH
20’ 1200 USGPH 6.0m 4500 LPH
FEATURES
Non corrosive material.
Stainless steel mechanical rotary seal.
Thermal and overload protection.
1/2HP, 115VAC, 60Hz, 4.0 A, (8.0 A when start).
FRICTION LOSS IN
PIPE NOT INCLUDED
NOTICE
This unit is not designed for applications
involving salt water or brine .
Use with salt water or brine will void
warranty.

FOR INFORMATION TEL: [phone] FAX: [phone]
INSTRUCTION STEPS
REPAIR PARTS
REF # DESCRIPTION
1 310111 Strainer / vertical support
2 310112 Stainer
3 310113 Discharge adaptor
4 310114 Pump casing
5 310115 Foot (3)
6 310116 Screws (top cover & Impeller) (4)
7 310117 Impeller washer
8 310118 Impeller
9 310119 Impeller sleeve
10 310120 seal plate screws (4)
11 310121 Oil seal
12 310122 Seal plate
13 310123 Seal plate o-ring
14 310124 Mechanical seal
15 310125 Complete motor
16 310126 Rubber gasket
17 310127 Capacitor
18 310128 Handle
19 310129 Cable screws (2)
20 310130 Cable tie
21 310131 Power cable
22 310132 Power cable plate
23 310133 Top cover
24 310134 O-Ring
25 310135 Cover set screw
Repair parts may be ordered from your authorized point of sale or from
BUR-CAM PUMPS 3
WARNING : NEVER RUN THE PUMP DRY
Install the pump at the appropriate place to transfer or at the source for waterfall and / or
fountain.
Run a 2” pipe to the desired discharge point.
Make sure that sand, rocks or any debris does not clog the suction screen.
STEP 1
STEP 2
STEP 3
MODEL 300910
Fountain pump
13
14
12
11
10
9
6
5
20
5
25
6
17
8
7
3
2324
19
18
22
21
16
15
4
12

FOR INFORMATION TEL: [phone] FAX: [phone]
4
TROUBLE SHOOTING GUIDE CHECKLIST
NEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR PRODUCT WITH THE POWER
CONNECTED. DON’T JUST UNSCREW THE FUSE OR TRIP THE BREAKER, REMOVE THE POWER
FROM THE RECEPTACLE.
Blown fuse
Tripped breaker
Plug disconnected
Corroded plug
Low water level
Thermal overloaded
Defective motor
Jammed impeller
Blocked suction/inlet
Discharge leak
Blocked line/pipe
Worn impeller
Defective motor
Replace
Reset
Re-install
Clean prongs
Add water and verify
Unplug the pump for 15 minutes
than restart.
Replace/repair
Clean
Check for debris in pit and clean
Repair
Check for debris or ice
Repair/replace
Replace/ repair
TROUBLE PROBABLE CAUSE ACTION
Motor does
not run.
Pump does
not deliver
full capacity.
TO THE END CONSUMER
If you have any problems with the product, before advising the store, where you’ve
purchased the pump, please contact us at 514 337-4415 , and ask for our sales
department, and they will be pleased to help you with any questions you might have,
concerning your installation.