Burley Baby Snuggler Instruction Manual

Baby Snuggler

Children must be able to sit upright without
support and have adequate neck strength to
support their head before being carried in a
trailer. With younger children, this product is
recommended for strolling and jogging use only.
Consult a pediatrician to determine if a child is
of sufficient developmental age to be carried in
a bicycle trailer.
Recommended age: 6 to 24 months
the Burley Baby Snuggler can be used in any
Burley child trailer with the 5-point harness
system (2003 and later), but works best
on those models with seat pad attachment
strips on the child seat. For more information,
consult your Authorized Burley Dealer or visit
www.burley.com.
Installation
SOLO TRAILER, ONE INFANT:
1. Remove existing shoulder harness pad and
seat pad. Insert shoulder straps through
openings in Baby Snuggler back. Use the
lower strap openings for a shorter infant,
and the upper openings for a longer
infant. FIGURE A
2. Insert crotch strap through opening in Baby
Snuggler bottom. FIGURE A
3. Slide padded tubes onto shoulder straps,
with straps oriented so that FLAT parts of
male buckles face each other. FIGURE A
4. Position infant in Baby Snuggler, with infant’s
upper back centered on the Snuggler’s
lumbar support.
5. Snap male buckles into Y-buckle, with
Y-buckle positioned at infant’s sternum.
Adjust straps so infant cannot move too far
forward in Snuggler. FIGURE A
6. To secure head and shoulders, adjust
side tension cords and toggles. The upper
Snuggler will narrow, cradling the infant’s
head. To change angle of infant’s legs, adjust
side straps. FIGURE C
Baby Snuggler
Installation Instructions
FIGURE A: Baby Snuggler Installation
FIGURE B: Baby Snuggler Installation in d’lite Trailer
FIGURE C: Baby Snuggler in Reclining Position
Seat
Belt
1. For Longer
Infant 1. For Shorter
Infant
3. Strap
Tubes
2. Crotch
Strap
Adjustable
Side Tension
Cord
Adjustable
Seat Crotch
Strap
Adjustable
Side Strap
Trailer
Front
Seat Belt
Snugly
Fastened

DOUBLE PASSENGER TRAILERS, ONE INFANT:
Install Baby Snuggler in center of trailer, using the two center shoulder straps and center crotch
strap. FIGURE B Follow steps 1-7.
DOUBLE PASSENGER TRAILERS, ONE INFANT, ONE CHILD:
Install Baby Snuggler on one side of trailer, using shoulder straps and crotch strap on that side.
Follow steps 1-7, positioning infant and making Baby Snuggler adjustments before placing child
in trailer seat.
DOUBLE PASSENGER TRAILERS, TWO INFANTS:
Install Baby Snugglers using both shoulder harnesses and two outer crotch straps.
Follow steps 1-7.
FOR TRAILERS WITH RECLINING SEAT FEATURE:
For added comfort, make the following adjustments to your trailer:
1. Loosen tension on the upper and lower straps behind the trailer seat.
2. Place Baby Snuggler in trailer, with Baby Snuggler bottom toward the front of the trailer
seat. Lengthen crotch strap. FIGURE C
3. Follow steps 1-7.
Consult your Burley trailer manual for more information about the reclining seat feature.
If you do not have a copy of your trailer instruction manual, do not use the Burley Baby Snuggler.
To replace your manual, go to http://burley.com/support/manuals_current.cfm.
ALWAYS SECURE CHILDREN WITH HARNESS AND LAP BELT BEFORE USE. SECURE ACCORDING TO INSTRUCTIONS ON TRAILER SEAT
LABEL AND IN OWNER’S MANUAL. CONSULT A PEDIATRICAN BEFORE USING THIS PRODUCT. NEVER LEAVE A CHILD UNOBSERVED OR
UNATTENDED. FAILURE TO DO SO COULD RESULT IN AN ACCIDENT AND SERIOUS INJURY OR DEATH.
WARNING
SINGLE PASSENGER MUST BE SEATED IN CENTER POSITION.
IMPORTANT:
STRAPS BEHIND CHILD SEAT MUST ALWAYS BE SECURED WHEN TRAILER IS IN USE.
IMPORTANT: