Byan Systems G2M Setup guide

-1-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
G2M Classic Control Board
Installation and Operators Manual
Specifications:
Power Supply: Single-Phase 115-Volt or 220-Volt 50/60 Hz AC
Motor Power Consumption: Up to 550 Watts or 3/4 HP
Electric Lock Output: 12-Volt DC 1-Amp Maximum
Accessory Power Output: 24-Volt AC 1-Amp Maximum
Input Power Fuse: 2-Amp, 250-Volt; 5mm x 20mm Tubular Glass
Motor Power Fuses: 6-Amp, 250-Volt; 5mm x 20mm Tubular Glass
307.334.2865 www.byan.com
Fax: [phone] Toll Free: 800.223.2926
P.O. Box 1384 | 413 South Linden Street | Lusk, Wyoming 82225
BYAN
SYSTEMS INC.
Automatic Gate and Access Control Products

-2-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1

-3-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
TABLE OF CONTENTS
PRODUCT WARNING .................................................................................................................................................Page 4
G2M Classic Board Description .............................................................................................................................. Page 5
Terminal Information ............................................................................................................................................ Page 6
Power and Motor Run Terminal Table .................................................................................................................. Page 6
Commercial Power Hook-Up ................................................................................................................................. Page 6
Accessory Terminal Table ...................................................................................................................................... Page 7
Accessory Hook-Up ................................................................................................................................................ Page 8
Timing Potentiometers .......................................................................................................................................... Page 9
S1 DIP Switches ...................................................................................................................................................... Page 9
S2 DIP Switches ...................................................................................................................................................... Page 9
12x10 Prewire Layout .......................................................................................................................................... Page 10
20x16 Prewire Layout ........................................................................................................................................ Page 11
24x20 Prewire Layouts ........................................................................................................................................ Page 12
24x20 Prewire Terminal Strip Guide ................................................................................................................... Page 13
20x16 Prewired Enclosure with Safety, Shadow and Free Exit Bases Wired to 2 Sets of Photobeams................. Page 14
20x16 Prewired Enclosure with Safety and Free Exit Bases Wired to 2 Sets of Photobeams................................ Page 15
20x16 Prewired Enclosure with Shadow and Free Exit Bases Wired to 2 Sets of Photobeams ............................ Page 16
20x16 Prewired Enclosure with Shadow and Safety Bases Wired to 2 Sets of Photobeams ................................ Page 17
20x16 Prewired Enclosure Wired to Miller Edge RBand RB-G-K10 Sensing Edge and Photobeams ..................... Page 18
20x16 Prewired Enclosure Wired to Transmitter Solutions RBand iGAZERKIT-UL
Sensing Edge and Photobeams .............................................................................................................................. Page 19
20x16 Prewired Enclosure Wired with a 24-Volt DC Transformer......................................................................... Page 20
20x16 Prewired Enclosure Wired with a 24-Volt DC Transformer and 24-Volt DC Photobeams .......................... Page 21
20x16 Prewired Enclosure Wired to a Miller Edge GEM-104 and Normally Open Sensing Edge ......................... Page 22
20x16 Prewired Enclosure Wired to Linear GRD Receiver .................................................................................... Page 23
Troubleshooting Guide .......................................................................................................................................... Page 24
T2M Leaf Delay Card .............................................................................................................................................. Page 25
Circuit Operation ................................................................................................................................................... Page 26
Final System Warnings .......................................................................................................................................... Page 27
Byan Systems, Inc. Warranty Information ........................................................................................................... Page 28

-4-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
THIS EQUIPMENT USES HIGH VOLTAGE.
TO REDUCE THE RISK OF SEVERE
INJURY OR DEATH, FOLLOW
ALL INSTALLATION INSTRUCTIONS.
THIS SYSTEM SHOULD ONLY BE INSTALLED
AND/OR MODIFIED BY
QUALIFIED TECHNICAL PERSONNEL
As a Byan Systems gate installer, you MUST inform your customer about all safety equipment that should be installed on
each job site. This is in accordance with your legal liability to your customer. Ensure that the protection and warning
signaling devices are operational and visible. These steps will aid in your defense should you become involved in litigation
regarding injury or damage.

-5-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
BYAN SYSTEMS G2M CLASSIC CONTROL BOARD
The G2M is a single phase, microprocessor controlled unit. It is capable of controlling up to two
¾-hp, 115-volt or 220-volt AC motors. Two different plug in accessory cards are available for the
G2M: a leaf delay card (which comes standard with every board), and a traffic light card (which
is available separately). There are three timing potentiometers as well as nine DIP switches
incorporated into the board to control different output functions.

-6-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
Terminal Strips:
There are two sets of terminals on the G2M control board. The first terminal strip is the Power and Motor Run
Terminal Block, located on the left side of the board below the transformer. This is where the incoming
commercial power and the outgoing power to the operators are connected. This terminal strip is made up of
three terminal blocks: 1) In-coming Power; 2) Motor One; and 3) Motor Two.
Power and Motor Run Terminals
Terminal
Number
Terminal Name / Description
Wire Colors
1
Commercial Power Input Neutral
115V White / 220V Black
2
Commercial Power Input Hot
115V Black / 220V Red
3
Motor One Close Directional
Black
4
Motor One Open Directional
Red
5
Motor One Common
White
6
Motor Two Close Directional
Black
7
Motor Two Open Directional
Red
8
Motor Two Common
White
Commercial Power Hook-Up*:
1. Hook up commercial power to Terminals 1 and 2 of the Power and Motor Run Terminal Strip.
2. Connect leads from the Motor No. 1 operator to Terminals 3, 4, and 5 of the Power and Motor Run Terminal
Strip.
3. Connect leads from the Motor No. 2 operator to Terminals 6, 7 and 8 of the Power and Motor Run Terminal
Strip.
4. Connect Motor Run Capacitors across each set of directional motor leads (between Terminals 3 and 4, and
Terminals 6 and 7).
115V White / 220V Black
115V Black / 220V Red
Capacitor
Capacitor
Black
Black
Red
Red
White
White
Motor 1
Motor 2
1
2
3
4
5
6
7
8

-7-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
The second terminal strip is the Accessory Terminal Strip. This is where ALL of the accessories are connected to
the controller board. This terminal strip is located on the bottom right of the G2M Controller Board. This terminal
strip consists of two socketed blocks to allow you to unplug the connector as a whole without removing wires. The
drawings on Pages 10-12 are color-coded for ease in determining wiring connections for accessories.
Accessory Terminal Table
Terminal
Numbers
Terminal Name
Possible Uses
1 - 2
Alarm Output
These terminals allow the connection of a device to alert
the user that people safe has been activated.
3 - 4
24-Volt AC 1-Amp Output
Power for accessories such as radio receivers, loop
detectors, or anything requiring 24-Volt AC 1-Amp may
be connected here.
5 –6
12-Volt DC 1-Amp Pulsed Electric
Lock Output
Magnetic or other types of lock release signals may be
connected here.
7 –9
People Safe Alarm Reset Input
A button or other Normally Open contact may be
connected here to reset the People Safe alarm output
relay.
8
People Safe Input
Normally Closed People Safe devices such as sensing
edges are connected here.
9
Safety Common Input
Common wires for people and car safety devices are
connected here.
10
Car Safe Input
Normally Closed Car Safe devices such as loop detectors
and photo beams are connected here.
11
Limit Switch Common Input
If limit switches are required, the common wires would
be connected here.
12
Close Limit Switch Input
If limit switches are required, the close limit switch
would be connected here.
13
Open Limit Switch Input
If limit switches are required, the open limit switch
would be connected here.
14 –15
Stop Input
A Normally Closed device used to stop the operators
such as a button may be connected here.
16
Control Function Common Input
This is where the common of devices used to open,
close, or reverse the gate would be connected.
17
Close Function Input
Devices only used to close the gate such as in-ground
loops, buttons, or photo beams are connected here.
18
Open Function Input
Devices only used to open the gate such as in-ground
loops, buttons, or radio receivers are connected here.
(Any Normally Open devices used to access the gate key
pads, card readers, etc.)
19
Reverse Function Input
Devices used to reverse the gates’ direction such as in-
ground loops, buttons, or radio receivers are connected
here.

-8-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
Accessory Hook-Ups*:
There are many accessories available that are compatible with the G2M that will give the end user different
options for safety, security, and system operations. Since it would be impossible to outline all possible
combinations, we will simply outline a few of the most common. Keep in mind; these instructions are specific to
the brand and model most commonly used by Byan Systems. Your accessories may differ from the ones listed
below. ALWAYS consult the Installation Instructions included with an accessory before connecting it to any
operating system.
Linear GRD_1 Radio Receiver:
1. Separate the four wires coming out of the bottom of the Receiver (1 Red, 1 Black, and 2 Gray).
2. Connect the black wire to Terminal 3 of the Accessory Terminal Strip.
3. Connect the red wire to Terminal 4 of the Accessory Terminal Strip.
4. Connect one of the gray wires to Terminal 16 of the Accessory Terminal Strip.
5. Connect the other gray wire to Terminal 18 of the Accessory Terminal Strip for open only or Terminal 19 for use as a
reversing device.
6. If an external antenna is required, locate the Bulk Head Connector supplied with the Receiver.
7. Drill one 3/8” hole in the enclosure where you would like to mount the antenna.
8. Install the Bulk Head Connector in the hole using the hardware included with the Receiver. Be sure to use thread
locking compound in the threads when installing the connector.
9. Connect the supplied coax between the Receiver and the Bulk Head Connector and attach the antenna to the
outside of the connector.
Mag-Lock Relay Using IDEC SH2B-05 Base w/RH2B-UDC12V Relay:
1. Connect Terminal 13 on the Relay Base to Terminal 5 of the Accessory Terminal Strip on the board.
2. Connect Terminal 14 on the Relay Base to Terminal 6 of the Accessory Terminal Strip on the board.
3. Connect Neutral or Ground from the Mag-Lock Transformer directly to the Mag-Lock.
4. Connect Hot from the Mag-Lock Transformer to Terminal 9 of the Relay Base.
5. Connect Terminal 1 on the Relay Base to the Mag-Lock.
Loop Detector Using IDEC SR3P-06 Base w/EDI LMA1500-120 Loop Detector:
1. Connect Terminals 7 and 8 to the in-ground loop leads.
2. Connect 120-Volt AC Neutral to Terminal 2 of the Detector Base.
3. Connect 120-Volt AC Hot to Terminal 1 of the Detector Base.
4. Connect desired signal wires from the Detector Base to the Accessory Terminal Strip of the G2M.
Shadow Using IDEC SH2B-05 Relay Base and RH2B-UAC110-120 Relay:
1. Connect Terminal 9 of the Relay Base to Terminal 5 of the Detector Base.
2. Connect Terminal 5 of the Detector Base to Terminal 9 of the Accessory Terminal Strip.
3. Connect Terminal 5 of the Relay Base to Terminal 10 of the Detector Base.
4. Connect Terminal 10 of the Detector Base to Terminal 10 of the Accessory Terminal Strip.
Safety:
1. Connect Terminal 5 of the Detector Base to Terminal 9 of the Accessory Terminal Strip.
2. Connect Terminal 10 of the Detector Base to Terminal 10 of the Accessory Terminal Strip.
Free Exit:
1. Connect Terminal 5 of the Detector Base to Terminal 16 of the Accessory Terminal Strip.
2. Connect Terminal 6 of the Detector Base to Terminal 18 of the Accessory Terminal Strip.

-9-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
Characteristics:
Adjustable Timing Potentiometers:
Color
Description
Minimum Time
Maximum Time
Green
Automatic Closing Timer
1 Second
1 Minute 30 Seconds
Blue
Opening Timer
3 Seconds
30 Seconds *
Red
Closing Timer
3 Seconds
30 Seconds *
*With DIP Switch 1 on S2 turned on, the maximum open and close times are doubled to 1 Minute.
DIP SWITCHES: Table S1
Number
Option Name
Option Description
1
Reversing Stroke
Function
When turned on, the operators will first close for 1 second
before opening.
2
Step-by-step Function
When turned on, each movement of the operators by any
reverse input will require an individual input (deactivates
automatic re-open function).
3
Automatic Closing
Function
When turned on, the operators will close by the time set
with the green timing potentiometer.
4
Reverse Button
Inoperative During
Opening
When turned on, any reverse input is deactivated during
the open cycle.
5
Closing Order by Car
Safety Contact
With DIP switch 3 off and 5 turned on, the operators will
close as soon as the car safety contacts are cleared.
6
*See Below
*See Below
7
Car Safety Contact
Operative During
Opening
When turned on, car safety contacts are active during the
open and close cycles. Input safety for vehicles only
works on closing movement unless Switch 7 is set ON.
*The function of DIP switch 6 is changed by the position of the jumper (JP1) located below the radio receiver card (J3).
Table S1a describes the function of DIP switch 6 and its relation to JP1.
Table S1a
JP1 Open
JP1 Closed
DIP Switch 6 ON
When power is applied to the board,
operators will automatically perform
a closing function.
The traffic light card will act as a
flashing light card (upper relay) and
a garage light card (lower relay).
DIP Switch 6 OFF
When power is applied to the board,
the operator will automatically
perform an opening function.
The traffic light card relays will act
as a green light (upper relay) and a
red light (lower relay).
Table S2
Number
Option Name
Option Description
1
Double Timing
When turned on, maximum opening and closing time is extended
from 30 Seconds to 1 Minute and maximum pause time is
extended from 45 Seconds to 1 Minute 30 Seconds.

-10-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
Byan Systems 12 x 10 Prewire Layouts:
NOTE: When Leaf Delay is engaged, Motor 1 will open first and Motor 2 will close first.
_________TERMINAL BLOCK 1 ____________ COMMERCIAL POWER ______
1 220-Volt AC Hot (Red)
2 115-Volt AC Hot (Black)
3 115-Volt AC Neutral (White)
4 Ground (Green)
_________TERMINAL BLOCK 2 _____ OPERATOR MOTOR TERMINALS______
10 Ground (Green)
11 Motor Directional (Black)
12 Motor 1 Directional (Red)
13 Motor 1 Common (White)
14 Ground (Green)
15 Motor 2 Directional (Black)
16 Motor 2 Directional (Red)
17 Motor 2 Common (White)
TERMINAL BLOCK 3 _________ACCESSORY TERMINALS_______
24+ UNUSED WITH G2M CLASSIC (Red)
18 24-Volt AC Common (Black)
19 24-Volt AC Positive (Red)
20 People Safe (Normally Closed) (White)
21 Common Safety
22 Car Safe (Blue)
23 Common Open/Reversing (Green)
24 Command Open (Normally Open) (Purple)
25 Command Reversing (Normally Open) (Orange)
6Amps
2Amps
6 Amps
Leaf Delay
Card
TrafficLight Card
FlashingLight Card
GarageLight Card
Daughter
Card
DIPSwitches
S1 S2
1
2
3
4
5
6
7
8
POWER TERMINALS
Pause
Timer Opening
Timer Closing
Timer
JP 1
Test Button
ACCESSORYTERMINALS
12345 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Transformer
S
W
I
T
C
H
B
O
X1
2
3
4
10
11
12
13
14
15
16
17
18
19
21
22
20
23
24
25
24+

-11-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
20 x 16 PREWIRE LAYOUT
2Amps
6 Amps
6Amps
Traffic Light Card
Flashing Light Card
GarageLightCard
Daughter
Card
DIPSwitches
S1 S2
1 2 3 4 5 6 7 8
POWER TERMINALS
Leaf Delay
Card
Pause
Timer Opening
Timer Closing
Timer
JP 1
Test Button
ACCESSORYTERMINALS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Transformer
Terminal Block 1
1 2 3 4
Terminal Block 2
5 6 7
Terminal Block 4
10 11 12 13 14 15 16 17
Terminal Block 7
(Optional)
HIGH VOLTAGE
SURGE PROTECTOR
(Optional)
LOW VOLTAGE
SURGE PROTECTOR
SHADOW
RELAY
(Optional)
MAG-LOCK
RELAY
(Optional)
7 DAY
TIMER
(Optional)
Terminal Block 3
8 9
(Optional)
32 33
Terminal Block 5
24+
18 19
20
22 23 24 25
Terminal Block 6
26 27 28 29 31 30
(Optional)
DETECTOR
SHADOW
BASE
DETECTOR
FREE EXIT
BASE
DETECTOR
SAFETY
BASE
TERMINALS
TB1 COMMERCIAL POWER
1220-VOLT AC HOT (RED) 2115-VOLT AC HOT (BLACK) 3115-VOLT AC NEUTRAL (WHITE) 4GROUND (GREEN)
TB2 OPERATOR MOTOR TERMINALS
5UN-INTERRUPTIBLE 115-VOLT AC (BLACK) 6UN-INTERRUPTIBLE 115-VOLT AC (WHITE) 7GROUND (GREEN)
3 INTERRUPTED VOLTAGE TERMINALS
8INTERRUPTED HIGH VOLTAGE 115 -VOLT AC (BLACK) 9INTERRUPTED HIGH VOLTAGE 115 -VOLT AC (WHITE)
TB4 OPERATOR MOTOR TERMINALS
10 GROUND (GREEN) 11 MOTOR 1 DIRECTIONAL (BLACK) 12 MOTOR 1 DIRECTIONAL (RED) 13 MOTOR 1 COMMON (WHITE) 14 GROUND (GREEN) 15 MOTOR 2 DIRECTIONAL (BLACK) 16 MOTOR 2 DIRECTIONAL (RED) 17 MOTOR 2 COMMON (WHITE)
-
TB5 ACCESSORY TERMINALS
24+ UNUSED WITH G2M CLASSIC (RED)
24-
18 VOLT AC COMMON (BLACK) 19 24 VOLT AC POSITIVE (RED) 20 PEOPLE SAFE (NORMALLY CLOSED) (WHITE) 21 N SAFETY (YELLOW)
COMMO
22 CAR SAFE (BLUE) 23 COMMON OPEN/REVERSING (GREEN) 24 COMMAND OPEN (NORMALLY OPEN) (PURPLE) 25 COMMAND REVERSING (NORMALLY OPEN) (ORANGE)
TB6 LOOP TERMINALS
26 FREE EXIT LOOP (GRAY) 27 FREE EXIT LOOP (BROWN) 28 SAFETY LOOP (GRAY) 29 SAFETY LOOP (BROWN) 30 SHADOW LOOP (GRAY) 31 SHADOW LOOP (BROWN)
TB -LOCK TERMINALS
7 MAG
32 MAG-LOCK (BROWN) 33 MAG-LOCK (BROWN)
NOTE: WHEN LEAF DELAY IS ENGAGED, MOTOR 1 WILL OPEN FIRST AND MOTOR 2 WILL CLOSE FIRST

-12-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
24 x 20 PREWIRE LAYOUT
Terminal Block 9
9
8
MAG-LOCK
RELAY
(Optional)
SHADOW
RELAY
(Optional)
Terminal Block 2
5
6
7
Terminal Block 3
10
11
12
13
14
15
16
17
Terminal Block 4
10
11
12
13
14
15
16
17
Terminal Block 10
9
8
Terminal Block 7
24+
18
19
20
22
23
24
25
Terminal Block 8
26
27
28
29
31
32
33
30
(Optional)
DETECTOR
SHADOW
BASE
DETECTOR
FREE EXIT
BASE
DETECTOR
SAFETY
BASE
2Amps
6 Amps
6Amps
Traffic Light Card
FlashingLight Card
Garage Light Card
Daughter
Card
DIP Switches
S1 S2
1
2
3
4
5
6
7
8
POWER TERMINALS
Leaf Delay
Card
Pause
Timer Opening
Timer Closing
Timer
JP 1
Test Button
ACCESSORYTERMINALS
1 2 3 4 5 6 7 8 9 10 1112 13 14 1516 17 1819
Transformer
2Amps
6 Amps
6Amps
TrafficLightCard
Flashing Light Card
Garage Light Card
Daughter
Card
DIP Switches
S1 S2
1
2
3
4
5
6
7
8
POWER TERMINALS
Leaf Delay
Card
Pause
Timer Opening
Timer Closing
Timer
JP 1
Test Button
ACCESSORYTERMINALS
1 2 3 4 5 6 7 8 9 10 111213 14 1516 17 18 19
Transformer
MAG-LOCK
RELAY
(Optional)
SHADOW
RELAY
(Optional)
Terminal Block 5
24+
18
19
20
22
23
24
25
Terminal Block 6
26
27
28
29
31
32
33
30
(Optional)
DETECTOR
SHADOW
BASE
DETECTOR
SAFETY
BASE
Terminal Block 1
1 2 3 4

-13-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
24 x 20 PREWIRE TERMINAL STRIP GUIDE
TB1 COMMERCIAL POWER
TB2 OPERATOR MOTOR TERMINALS
1
220-VOLT AC HOT
(RED)
5
UNINTERRUPTIBLE 115-VOLT AC
(BLACK)
2
115-VOLT AC HOT
(BLACK)
6
UNINTERRUPTIBLE 115-VOLT AC
(WHITE)
3
115-VOLT AC NEUTRAL
(WHITE)
7
GROUND
(GREEN)
4
GROUND
(GREEN)
TB4 EXIT OPERATOR MOTOR TERMINALS
TB3 OPERATOR MOTOR TERMINALS
10
GROUND
(GREEN)
10
GROUND
(GREEN)
11
MOTOR 1 DIRECTIONAL
(BLACK)
11
MOTOR 1 DIRECTIONAL
(BLACK)
12
MOTOR 1 DIRECTIONAL
(RED)
12
MOTOR 1 DIRECTIONAL
(RED)
13
MOTOR 1 COMMON
(WHITE)
13
MOTOR 1 COMMON
(WHITE)
14
GROUND
(GREEN)
14
GROUND
(GREEN)
15
MOTOR 2 DIRECTIONAL
(BLACK)
15
MOTOR 2 DIRECTIONAL
(BLACK)
16
MOTOR 2 DIRECTIONAL
(RED)
16
MOTOR 2 DIRECTIONAL
(RED)
17
MOTOR 2 COMMON
(WHITE)
17
MOTOR 2 COMMON
(WHITE)
TB7 EXIT ACCESSORY TERMINALS
TB5 ENTRY ACCESSORY TERMINALS
24+
NOT USED WITH G2M CLASSIC
(RED)
24+
NOT USED WITH G2M CLASSIC
(RED)
18
24-VOLT AC COMMON
(BLACK)
18
24-VOLT AC COMMON
(BLACK)
19
24-VOLT AC POSITIVE
(RED)
19
24-VOLT AC POSITIVE
(RED)
20
PEOPLE SAFE (NORMALLY CLOSED)
(WHITE)
20
PEOPLE SAFE (NORMALLY CLOSED)
(WHITE)
COMMON SAFETY
COMMON SAFETY
22
CAR SAFE
(BLUE)
22
CAR SAFE
(BLUE)
23
COMMON OPEN / REVERSING
(GREEN)
23
COMMON OPEN / REVERSING
(GREEN)
24
COMMAND OPEN (NORMALLY OPEN)
(PURPLE)
24
COMMAND OPEN (NORMALLY OPEN)
(PURPLE)
25
COMMAND REVERSING (NORMALLY OPEN)
(ORANGE)
25
COMMAND REVERSING (NORMALLY OPEN)
(ORANGE)
TB8 EXIT LOOP TERMINALS
TB6 ENTRY LOOP TERMINALS
26
FREE EXIT LOOP
(GRAY)
28
SAFETY LOOP
(GRAY)
27
FREE EXIT LOOP
(BROWN)
29
SAFETY LOOP
(BROWN)
28
SAFETY LOOP
(GRAY)
30
SHADOW LOOP
(GRAY)
29
SAFETY LOOP
(BROWN)
31
SHADOW LOOP
(BROWN)
30
SHADOW LOOP
(GRAY)
32
MAG-LOCK
(BROWN)
31
SHADOW LOOP
(BROWN)
33
MAG-LOCK
(BROWN)
32
MAG-LOCK
(BROWN)
33
MAG-LOCK
(BROWN)
TB9 ENTRY INTERRUPTED VOLTAGE TERMINALS
8
INTERRUPTED HIGH VOLTAGE 115-VOLT AC
(BLACK)
TB10 EXIT INTERRUPTED VOLTAGE TERMINALS
9
INTERRUPTED HIGH VOLTAGE 115-VOLT AC
(WHITE)
8
INTERRUPTED HIGH VOLTAGE 115-VOLT AC
(BLACK)
9
INTERRUPTED HIGH VOLTAGE 115-VOLT AC
(WHITE)
NOTE: WHEN LEAF DELAY IS ENGAGED, MOTOR 1 WILL OPEN FIRST AND MOTOR 2 WILL CLOSE FIRST.

-14-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
20x16 Prewired Enclosure with Shadow, Safety & Free Exit Bases Wired to 2 Sets of Photobeams
BYANSYSTEM, INC.
20 x16 PRE-WIRE
WIRING DIAGRAM
DRAWN DATE
ATH 3/2018
MOTORCAPS.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
L N G
DUPLEX RECEPT.
SWITCH
10 11 12 13 14 15 16 17
TB4
5 6 7 TB2
TB1
TB7
32 33
TB 5
MAGLOCK
1
2
3 4 5
6
7
8Traffic L ight Card
Flas hing LightC ard
Garage Light Card
Le af
Delay
Card
Pause Timer Opening
Timer Closing
Timer
G2MCLASSIC
Transformer
6Amps
2Amps
6Amps
POWER TERMINALS
JP1
S1 S2
DIP Switches
ACCESSORYTERMINALS
Test
Button
SAFETYDETECTORBASE
SHADOWDETECTORBASE FREEEXITDETECTORBASE
Optional
Mag Lock Relay
Optional
Shadow Relay
89
TB3
TB6
26 27 28 29 30
31
24+ 25 24 23 22 21 20 19 18
This equipment uses high voltage. Serious injury or death may occur if the system is improperly configured. This system should only be installed and/or modified by qualified technical personnel. Read all owner’s manuals and safety instructions.
WARNING:
Photobeam
Set 1 Photobeam
Set 2

-15-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
20x16 Prewired Enclosure with Safety & Free Exit Bases Wired to 2 Sets of Photobeams
BYANSYSTEM, INC.
20 x16 PRE-WIRE
WIRING DIAGRAM
DRAWN DATE
ATH 3/2018
MOTORCAPS.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
L N G
DUPLEX RECEPT.
SWITCH
10 11 12 13 14 15 16 17
TB4
5 6 7 TB2
TB1
TB7
32 33
TB 5
MAGLOCK
1
2
3 4 5
6
7
8
G2MCLASSIC
Traffic L ight Card
Flas hing LightC ard
Garage Light Card
Le af
Delay
Card
Pause Timer Opening
Timer Closing
Timer
Transformer
6Amps
2Amps
6Amps
POWER TERMINALS
JP1
S1 S2
DIP Switches
ACCESSORYTERMINALS
Test
Button
SAFETYDETECTORBASE FREEEXIT DETECTORBASE
Optional
Mag Lock Relay
89
TB3
TB6
26 27 28 29 30
31
24+ 25 24 23 22 21 20 19 18
This equipment uses high voltage. Serious injury or death may occur if the system is improperly configured. This system should only be installed and/or modified by qualified technical personnel. Read all owner’s manuals and safety instructions.
WARNING:
Photobeam
Set 1 Photobeam
Set 2

-16-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
20x16 Prewired Enclosure with Shadow & Free Exit Bases Wired to 2 Sets of Photobeams
BYANSYSTEM, INC.
20 x16 PRE-WIRE
WIRING DIAGRAM
DRAWN DATE
ATH 3/2018
MOTORCAPS.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
L N G
DUPLEX RECEPT.
SWITCH
10 11 12 13 14 15 16 17
TB4
5 6 7 TB2
TB1
TB7
32 33
TB 5
MAGLOCK
1
2
3 4 5
6
7
8
G2MCLASSIC
Traffic Light Card
Flas hing LightC ard
Garage Light Card
Le af
Delay
Card
Pause Timer Opening
Timer Closing
Timer
Transformer
6Amps
2Amps
6Amps
POWER TERMINALS
JP1
S1 S2
DIP Switches
ACCESSORYTERMINALS
Test
Button
SHADOWDETECTORBASE FREEEXIT DETECTORBASE
Optional
Mag Lock Relay
Optional
Shadow Relay
89
TB3
TB6
26 27 28 29 30
31
24+ 25 24 23 22 21 20 19 18
This equipment uses high voltage. Serious injury or death may occur if the system is improperly configured. This system should only be installed and/or modified by qualified technical personnel. Read all owner’s manuals and safety instructions.
WARNING:
Photobeam
Set 1 Photobeam
Set 2

-17-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
SHADOWDETECTORBASE
20x16 Prewired Enclosure with Shadow & Safety Bases Wired to 2 Sets of Photobeams
BYANSYSTEM, INC.
20 x16 PRE-WIRE
WIRING DIAGRAM
DRAWN DATE
ATH 3/2018
MOTORCAPS.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
L N G
DUPLEX RECEPT.
SWITCH
10 11 12 13 14 15 16 17
TB4
5 6 7 TB2
TB1
TB7
32 33
TB 5
MAGLOCK
1
2
3 4 5
6
7
8
G2MCLASSIC
Traffic Light Card
Flas hing LightC ard
Garage Light Card
Le af
Delay
Card
Pause Timer Opening
Timer Closing
Timer
Transformer
6Amps
2Amps
6Amps
POWER TERMINALS
JP1
S1 S2
DIP Switches
ACCESSORYTERMINALS
Test
Button
SAFETYDETECTORBASE
Optional
Mag Lock Relay
Optional
Shadow Relay
89
TB3
TB6
26 27 28 29 30
31
24+ 25 24 23 22 21 20 19 18
This equipment uses high voltage. Serious injury or death may occur if the system is improperly configured. This system should only be installed and/or modified by qualified technical personnel. Read all owner’s manuals and safety instructions.
WARNING:
Photobeam
Set 1 Photobeam
Set 2

-18-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
ACCESSO RY TERMINALS
L eaf
D e lay
C ard
Pa use
Ti me r Opening
Time r Cl osing
Timer
G2MCLASSIC
Transformer
2Amps
6 Amps
T raf fi c Li ght Ca r d
F las hi ng Li gh t C ard
Ga r age L ig ht Ca rd
6Amps
3 4 5 6 7 8
1 2
POWER TERMINALS
JP1
S1 S2
DIPSwitches
Test
Button
10 11 12 13 14 15 16 17
TB4
L N G
TB1
DUPLEX RECEPT.
SWITCH
5 6 7 TB2 8 9
TB3
MOTORCAPS.
MAGLOCK
Optional
Mag Lock Relay
TB7
32 33
Optional
Shadow Relay
TB6
26 27 28 29 30
31
SAFETYDETECTORBASE
SHADOWDETECTORBASE FREEEXITDETECTORBASE
TB5
24+ 25 24 23 22 21 20 19 18
20x16 PRE-WIRED BACKBOARD WITH RBAND RB-G-K10 SENSING EDGE AND PHOTOBEAMS
pre-wired backplate. All accessories must be wired “in series”to allowmultiple safety accessories to
In this example, all accessories are wired as on a BYAN SYSTEMS 3-base
NORMALLY CLOSED
be connected at one time. (Accessories can be wired as “car safe”OR as “people safe”.
Photobeam Connection: Disconnect the jumpered connection of the wire from the Shadow Base and the Safety Base from
GREEN
in of the Shadow Base. Wire nut the wire of the photobeam to the wire of the Safety
#5 WHITE GREEN
Base. Connect the common wire of the photobeam ( ) to Pin of the Shadow Base.
YELLOW #5 Leave all
other wiresof the Shadow Base as-is. Connect the wire of the photobeam to Terminal .
RED #24+
Connect the wire of the photobeam to Terminal (see diagram below).
BLACK #18
Sensing Edge Connection: Connect the S1 connection to the blue wire of the sensing edge and the brown wire to theradio signal of the sensing edge. There are no DIP switches to set on the . After you have programmed the
TRANSMITTER
, depress the blue button on the to synchronize
RECEIVER TRANSMITTER the two units. Make sure that the signal is directed
TRANSMITTER’S
toward the and in line of sight to ensure that the radio signal
RECEIVER
is strong betweenthe two units.
Miller Edge RB-TX10 Transmitter
Phot eamob
Phot eamob
GateLeaf
GateLeaf
Make sure your DIP switches are set correctly. Program your using the blue button
RECEIVER
located next to the DIPswitches (R1 program is used here). Once programming is set, you will hear 2 beeps from the . Press and
RECEIVER
release the blue button of the to
TRANSMITTER
test communication (the green light on the TRANSMITTER will blink). The ATEST and the R1 and R2 LEDs on the will
RECEIVER
light solidly.
Miller Edge RB-G-RX10 Receiver
O N D I P
1 2 3 4
12/24V
+ - CS1
C1
BS1 CS 2 C 2 BS2 NO 3 C 3 COM
1 2 3 4
ON OFF ON ON
DIP SWITCH SETTINGS
ONRBANDRECEIVER
ATEST

-19-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
pre-wired backplate. All accessories must be wired “in series”to allow multiple safety accessories to
RBAND iGAZEREKIT-UL SENSING EDGE AND PHOTOBEAMS
Phot eamob
Phot eamob
GateLeaf
GateLeaf
Make sure your DIP Swtiches are set correctly. On your , set all 6
RECEIVER
switches to the position. On the
OFF
TRANSMITTER also set all 6 switches to the position. (These are the way
OFF
they come directly from Transmitter Solutions for this model.)
Transmitter Solutions
iGAZEREKIT-UL Receiver
ON
123456
Test Pol arit y
Buzzer OFF
Frequency
Out1 10K
Out2 10K
Sensing Edge Connection: Connect the power from the RECEIVER of the sensing edge by connecting the BLACK wire to the second terminal on the receiver and connecting the other end to Terminal #18 of the pre-wired backplate. Next connect the RED wire to the first terminal of the receiver and connect the other end to Terminal #24+ of the pre-wired backplate. Connect the common wire of the receiver (YELLOW) to the third terminal of the receiver, connecting the other end to Terminal #21 of the pre-wired backplate. Lastly, connect the Normally Closed wire (BLUE) to the fifth terminal of the receiver to Terminal #20 (People Safe) on the pre-wired backplate (see diagram to the left).
Transmitter Solutions iGAZERE Transmitter
Safety1 Safety2
Safe ty1 Type Safe ty2 Type Low P ower Frequ ency F
Configuration
ON
Prog/Test1 Prog/Test2
Photobeam Connection: Disconnect the jumpered connection of the wire from the Shadow Base and the Safety Base
GREEN
from of the Shadow Base. Wire nut the wire of the photobeam to the wire of the Safety
#5 WHITE GREEN
Base. Connect the common wire of the photobeam ( ) to Pin of the Shadow Base.
YELLOW 5Leave all
other wires of the Shadow Base as-is. Connect the wire of the photobeam to Terminal .
RED #24+
Connect the wire of the photobeam to Terminal (see diagram below).
BLACK #18
In this example, all accessories are wired as on a BYAN SYSTEMS 3-base
NORMALLY CLOSED
be connected at one time. (Accessories can be wired as “car safe”OR as “people safe”.
20x16 PRE-WIRED BACKBOARD WITH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
ACCESSORY TERMINALS
Leaf
Delay
Ca rd
Pause
Timer Opening
Timer Closing
Timer
G2MCLASSIC
Transformer
2 Amps
6 Amps
Tra ffic L ig ht Card
FlashingL ig ht Card
Garage Light Card
6 Amps
3 4 5 6 7 8
1
2
POWER TERMINALS
JP1
S1 S2
DIP Switches
Test
Button
10 11 12 13 14 15 16 17
TB4
L N G
TB1
DUPLEX RECEPT.
SWITCH
5 6 7 TB2 89
TB3
MOTORCAPS.
MAGLOCK
Optional
Mag Lock Relay
TB7
32 33
Optional
Shadow Relay
TB6
26 27 28 29 30
31
SAFETYDETECTORBASE
SHADOWDETECTORBASE FREE EXIT DETECTORBASE
TB5
24+ 25 24 23 22 21 20
19 18

-20-
BYAN G2M CLASSIC CONTROL BOARD | Rev. 2019.6.1
20x16 Prewired Enclosure with 24V DC Transformer
24VDC
Transformer
BYANSYSTEM, INC.
20 x16 PRE-WIRE
WIRING DIAGRAM
DRAWN DATE
ATH 3/2018
This equipment useshigh voltage. Serious injury ordeath may occur if the system is improperly configured. This system should onlybe installed and/or modified by qualified technical personnel. Read all owner’smanuals and safety instructions.
TB 5
24+ 25 24 23 22 21 20 19 18
MOTORCAPS.
DUPLEX RECEPT.
SWITCH
10 11 12 13 14 15 16 17
TB4
5 6
7 TB2
L N G
TB1 Leaf
Dela y C ard
Pause
Timer Opening
Timer Closing
Timer
G2MCLASSIC
Transformer
Traffic LightCard
Fla s hingLight Card G arage Lig ht Ca rd
6Amps
1
2
3 4 5
6
7 8
POWER TERMINALS
2 Amps
6Amps
JP1
S1 S2
DIPSwitches
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
ACCESSORYTERMINALS
Test
Button
SAFETYDETECTORBASE
SHADOWDETECTORBASE FREEEXITDETECTORBASE
TB7
32 33
MAGLOCK
Optional
Mag Lock Relay
Optional
Shadow Relay
TB 6
26 27 28 29 30
31
Connects to the negative connector of the device it is powering.