BYOU CB/BY Installation guide

1
L8542497 ENG 10/2009 rev 0
Emergency battery kit
CB.BY
MADE IN ITALY

2
INTENDED USE
Emergency battery kit.
The kit can be used with the JUMP, PRET-
TY, FREEDOM and BEAUTY units made by
BYOU, and allows the device to work tem-
porarily when there is no mains power.
The number of operations that are possible
when there is no power from the mains de-
pends on the batteries’ state of charge, on
the type of device and on climatic factors.
BYOU products are covered by a 2-year
warranty.
However, BYOU srl shall not be responsi-
ble for damages caused by improper use or
by the improper installation of products or
components.
The manufacturer may change the descrip-
tions and figures in this manual at any time.
Furthermore, the manufacturer reserves the
right to make changes to the products’ tech-
nical, construction or commercial features
without necessarily updating this manual at
the same time.
The kit is composed of the following parts:
1) Battery charger board. The battery charger
board must be connected between the bat-
teries and the control station using the ca-
bles supplied. The board automatically pow-
ers the device when there is no mains power,
and maintains the batteries’ charge when the
device is powered by the mains.
2) Backup batteries. Two 24 V 2100 mAh
battery packs, with quick connector for con-
nection to the battery charger board.
3) Bracket for fastening the batteries to the
motor on the JUMP unit
4) Bracket for fastening the batteries to the
motor on the PRETTY unit
5) Bracket for fastening the batteries inside
the control station’s container on the BEAU-
TY unit (CP.BTY).
6) Cable for connecting the battery charger
to the control unit.
Product description Contents of kit
1 2
4
3
5 6
TECHNICAL DETAILS CB.BY
Batteries NiMh
Voltage 24Vdc
Charging current 300 mAh
JUMP PRETTY BEAUTY FREEDOM
Average number of cy-
cles when there is no
power from the mains
80 60 60 80

3
Installation on JUMP unit
Cut off the mains power supply before carrying
out any operation.
Using a screwdriver, open the passage for the
cables (A). If necessary, lower the gearmotor
as described in the instructions for the JUMP
unit:
A
Fasten the batteries to the gearmotor using the
bracket and screws supplied. Pass the con-
nection cable through the cable passage A:
If you previously lowered the gearmotor, return
it to its operating position.
Open the gearmotor assembly following the in-
structions supplied with the JUMP unit.
Disconnect the battery charger connector
(shown in the figure) from the control station’s
cover:
On the battery charger, re-
move the screw on the side
opposite the terminal board.
Using the screw supplied, install the battery
charger as shown in the figure:
Connect the batteries and the battery charger
as described in the “Connections” section.
Close the gearmotor assembly following the
instructions supplied with the JUMP unit.
TCIC 3,5x9,5
TCIC 2,9x22

4
Installation on PRETTY unit
Cut off the mains power supply before carrying
out any operation.
Remove the protective casing from the gear-
motor with the control station (PRETTY.A)
following the instructions supplied with the
PRETTY unit.
Install the batteries using the relative bracket
and screws as shown in the figure:
On the battery charger, re-
move the screw on the side
opposite the terminal board.
Disconnect the battery charger connector
(shown in the figure) from the control station’s
cover:
Using the screw supplied, install the battery
charger as shown in the figure:
Connect the batteries and the battery charger
as described in the “Connections” section.
Close the gearmotor assembly following the
instructions supplied with the PRETTY unit.
TCIC 3,5x9,5
TCIC 3,5x16

5
Installation on BEAUTY unit
Connect the batteries and the battery charger
as described in the “Connections” section.
Close the control station following the instruc-
tions supplied with the BEAUTY unit.
Cut off the mains power supply before carrying
out any operation.
Open the control station, following the instruc-
tions supplied with the BEAUTY unit.
Install the batteries using the relative bracket
and screws as shown in the figure:
Disconnect the battery charger connector
(shown in the figure) from the control station’s
cover:
Put the battery charger in the position shown
in the figure (no screws are required):
TCIC 3,5x9,5