CalAmp 140-5016-500 User manual

Package Contents — Basic or Full-Duplex Unit
If you ordered Guardian part number:
Part Number
Description
140-5016-500
VHF 136-174 MHz Guardian Basic Unit
140-5016-501
VHF 136-174 MHz Guardian Full-Duplex Unit
140-5026-500
VHF 215-240 MHz Guardian Basic Unit
140-5026-501
VHF 215-240 MHz Guardian Full-Duplex Unit
140-5046-300
UHF 406.1-470 MHz Guardian Basic Unit
140-5046-301
UHF 406.1-470 MHz Guardian Full-Duplex Unit
140-5046-501
UHF 450-512 MHz Guardian Basic Unit
140-5046-501
UHF 450-512 MHz Guardian Full-Duplex Unit
140-5096-500
MAS 928-960 MHz Guardian Basic Unit
140-5096-501
MAS 928-960 MHz Guardian Full-Duplex Unit
Your package contains:
(1) Guardian Serial Modem
(1) Power Cable
(1) 8-Pole Socket Connector
Package Contents — Two-Piece Kit
If you ordered Guardian as part of a kit number:
Part Number Description
250-5016-500
VHF 136-174 MHz Guardian Demo Kit
250-5026-500
VHF 215-240 MHz Guardian Demo Kit
250-5046-300
UHF 406-470 MHz Guardian Demo Kit
250-5046-500
UHF 450-512 MHz Guardian Demo Kit
250-5096-500
MAS 928-960 MHz Guardian Demo Kit
Your package contains:
(2) Guardian Basic or Full-Duplex Serial Modems
(2) SMA-Male to BNC-Female Connectors
(2) SMA-Female to BNC-Male Connectors
(2) TNC-Male to BNC-Female Connectors
(2) Mini Circuits 5 W 20 dB Attenuators
(2) Flex Rubber Duck Antennas (VHF, UHF, or 900 MHz)
(2) 120 VAC to 12 VDC Power Supply
(1) 72 in. Serial Programming Cable
(1) Start Up CD-ROM and Product Information Card
Minimum Requirements
Interface and configuration of this device requires a user PC with an available serial COM
port interface, Microsoft Windows 98 or newer, and a web browser.
Technical Support
For assistance with this product, contact CalAmp technical support.
Email [email protected]
Phone[phone]
Or visit the Support section of our website at http://www.calamp.com/support.
Any changes or modifications not expressly approved by the party responsible for compliance (in the country
where used) could void the user’s authority to operate the equipment.
CalAmp reserves the right to update its products, software, or documentation without obligation to notify any
individual or entity. Product updates may result in differences between the information provided and the
product shipped. For access to the most current product documentation and application notes, visit
www.calamp.com.
UL Listed models only
When operating at elevated temperature extremes, the surface may exceed
+70 Celsius. For user safety, the Fusion should be installed in a restricted access
location.
WARNING — EXPLOSION HAZARD, do not connect while circuit is live unless
area is known to be non-hazardous.
1401 North Rice Avenue
Oxnard, CA 93030
Tel: [phone]
Fax: [phone]
e mail: [email protected]
ABOUT CALAMP
CalAmp is a leading provider of wireless communications products that enable anytime/anywhere
access to critical information, data and entertainment content. With comprehensive capabilities
ranging from product design and development through volume production, CalAmp delivers cost-
effective high quality solutions to a broad array of customers and end markets. CalAmp is the
leading supplier of Direct Broadcast Satellite (DBS) outdoor customer premise equipment to the
U.S. satellite television market. The Company also provides wireless data communication solutions
for the telemetry and asset tracking markets, private wireless networks, Interoperable Train Control
(ITC) radio transceivers for use in railroad Positive Train Control (PTC) applications, public safety
communications and critical infrastructure and process control applications. For additional
information, please visit the Company’s website at www.calamp.com.
Quick Start Guide
Guardian™
SERIAL RADIO MODEM FOR LICENSED SPECTRUM
© 2011-2014 CalAmp
PN 004-5006-000 Rev A
Revised October 2014
All specifications are typical and
subject to change without notice.
CalAmp
1401 N Rice Avenue
Oxnard, CA 93030
t: 805.987.9000 | f: 805.987.8359
www.calamp.com

Setup and Configuration
It is easy to set up a Guardian network to verify basic unit operation and experiment with
network designs and configurations. An Rx/Tx antenna is required for basic operation.
Important: Use attenuation between all demo units to reduce the amount of
signal strength in the test environment.
Device Connections
Refer to the following diagram for the proper device connections for basic operation.
Field Programming Software
The Guardian Field Programming Software (FPS) is the programming and diagnostic
software for the Guardian serial radio modem. The FPS allows the user to edit and
program user programmable settings, interactively tune modem and RF parameters, and
monitor diagnostic data from the Guardian.
INSTALLING THE FPS
To use the FPS, you will need a PC with Windows 98 or later and at least one operational
COM port available.
Step 1Open the .zip file and open the setup.exe application. After the application is
extracted from the .zip file, the Guardian Programmer Setup window opens. Click Next.
INSTALLING THE FPS (continued)
Step 2Setup shows the destination location where the Guardian FPS files will be
installed. Click Next to continue.
Step 3 Setup shows the program group in the Start Menu that will be created or to which
the Guardian FPS will be added. Click Next to continue.
Note: Accept the default installation location and program group unless there is
reason to change them.
Setup displays the destination and program group and provides the opportunity to go
back to change either if necessary.
Step 4Click Install to begin installation. Setup displays the progress as files are extracted
and installed and displays a window similar to the following when complete.
When finished, click Finish to exit Setup.
USING THE FPS
Make sure all connections are made as shown in the Device Connections diagram and
then power the Guardian.
Step 1Locate the CalAmp Utils program group (or if you named it differently during
installation) and select the Guardian application.
Step 2 From the Guardian Programmer window, click Config in the upper left corner.
This will open the User Configuration window and read configuration information from
the device, auto-populating the Diagnostics section, and the RSSI bar will indicate
received signal strength.
Step 3 Click Link Configuration in the lower left corner of the User Configuration
window. Set the RF Link, COM Port, and Modem Setting as required. Click Save Changes
when finished.
Your Guardian modem is now ready for use. For advanced network settings, please refer
to the Guardian Serial Radio Modem User Manual (PN 001-5006-000) provided, or our
online support library at www.calamp.com.