Calculated Industries 6425 User manual

USER’S
GUIDE
DIGIROLLER
™
PLUS II
DIGITAL MEASURING WHEEL
MODEL 6425
• Gebrauchsanweisung
• Guide de l’utilisateur
• Guía del usuario

CALCULATED INDUSTRIES
®
AREA #

User’s Guide — 1
Introduction
THE DIGIROLLER
™
PLUS II
The revolutionary DigiRoller™Plus II is a digital measuring tool that
lets you roll distances quicker and easier than ever before! Replacing
the tape measure and mechanical measuring wheel, it measures linear
distances and displays them digitally, calculates area and volume,
stores multiple measurements in memory, and performs other handy
functions that let one person measure faster, more accurately, and
more conveniently. If your job involves measuring distances or taking
square footage, the new DigiRoller™Plus II is the tool for you!
■Large digital display located in handle for easy viewing
■Measures and stores Length, Width, and Height
■Calculates Area, Volume, and Wall Area
■Takes true “Wall-to-Wall” measurements
■Measurement unit selection and conversion
■Count and AutoCount functions
■Programmable “Fixed Distance”
■Stores up to nine different “Areas” or measurements
■Ergonomic and durable
■And much, much more!

2 — DigiRoller
™
Plus II
Table of Contents
Getting Started
Turning the DigiRoller™Plus II On/Off. . . . . . . . . . . . . . . . . . . . . 3
DigiRoller™Plus II Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Layout/Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Display Test/Annunciators . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Changing Units of Measurement . . . . . . . . . . . . . . . . . . . . . . . 11
Turning the Bell On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Taking Measurements
“Rolling” a Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Storing/Recalling Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Deleting Stored Measurements . . . . . . . . . . . . . . . . . . . . . . . . 16
Using the Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Taking Wall-to-Wall Measurements . . . . . . . . . . . . . . . . . . . . . 17
Taking Area Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Additional DigiRoller™Plus II Features
Lighting the Display Background . . . . . . . . . . . . . . . . . . . . . . . 21
Taking Volume Measurements . . . . . . . . . . . . . . . . . . . . . . . . . 22
Storing/Recalling Multiple Measurements . . . . . . . . . . . . . . . . 25
Editing Stored Measurements . . . . . . . . . . . . . . . . . . . . . . . . . 29
Deleting All Area Number Measurements . . . . . . . . . . . . . . . . 31
Taking Wall Area Measurements. . . . . . . . . . . . . . . . . . . . . . . 32
Using AutoCount/Fixed Distance Mode . . . . . . . . . . . . . . . . . 34
Deleting All Stored Values . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix
Changing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Changing/Calibrating Wheel Size . . . . . . . . . . . . . . . . . . . . . 37
Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Caring for your DigiRoller™Plus II. . . . . . . . . . . . . . . . . . . . . . . 43
Common Questions/Answers . . . . . . . . . . . . . . . . . . . . . . . . . 44
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Repair and Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
German, French and Spanish Translations. . . . . . . . . . . . . . . . 48

User’s Guide — 3
GETTING STARTED
Turning the DigiRoller™Plus II On/Off
On/Off Key
Turn the DigiRoller™Plus II on by pressing the [On/Off] key. To turn
it off, press the key again.
Auto Shut-Off
The DigiRoller™Plus II is designed to shut itself off if not used for 4-6
minutes. Values shown on the display will be cleared. However,
when you turn the unit on again, the previously displayed value will
re-display. All stored values will be retained.
To Set To Metric Mode
1. Turn unit on.
2. Press the [Set] key.
3. Press the [On/Off] key.
4. Press and hold the [Reset] key.
5. Press the [On/Off] key while continuing to
hold the [Reset] key.
6. Press the [Rcl] key to enter Metric Mode.
*Press the [LxW] key to enter Imperial Mode.

4 — DigiRoller
™
Plus II
cam locks
adjustable shaft
handle/battery
compartment
wheel (1 meter)
wheel hub
wrist strap
LCD display
kickstand
DigiRoller Plus™II Parts

User’s Guide — 5
Key Layout / Definitions
The DigiRoller™Plus II is unique to measuring wheels because it has
keys that allow you to store and manipulate the distances measured.
The following is a list of keys that you may use as you operate the
unit: (see page 10 for a list of LCD annunciators)
Power On/Off Key — Turns the unit on or off.
Length Key — Enters and stores rolled length value.
Width Key — Enters and stores rolled width value.
Area Key — Calculates and displays rolled area.
Multiplies the entered length value by the entered
width value.
CALCULATED INDUSTRIES
®
AREA #

6 — DigiRoller
™
Plus II
Units of Measurement Key — Selects desired unit
format: Feet-Inches, Decimal Feet, Decimal Inches,
Yards, Meters, and Acres (area display only). Each press
of this key will convert the displayed measurement to
another unit format.
Delete/All Clear Key — Deletes, or erases, the values
stored in the next key pressed (e.g., [DEL] [L] deletes
the current measurement stored as length, [DEL] [W]
deletes the current measurement stored as width,
etc). To perform an All Clear, press [Set] [DEL] [DEL].
This key sequence will clear all stored data and
memory registers.
Recall Key — Recalls and displays the value of the
next key pressed (for example, [Rcl] [W] displays the
value stored in the Width key). [Rcl] [Rcl] will recall
a previously rolled value that has been cleared or
deleted.
Memory Add Key — Stores any displayed value into
permanent memory. When you store a value in
memory, it is added to the values you previously
stored in memory. Note that you cannot add two
measurements of different levels of dimensions (for
example, you cannot add feet-inches and square feet).
Memory Subtract Key — Subtracts the displayed
value from permanent memory.

User’s Guide — 7
Set Key — Used to access special functions.
AddWheel Radius Key — Adds the wheel radius (first
press) or diameter (second press) to the total linear
measurement, to allow for true wall-to-wall distance.
Reset/Clear Display Key — Clears the display to 0.
Does not clear stored values.
Start/Stop Key — This key switches the unit between
start and stop modes. You will press this key to begin
measuring. When you are in stop mode, a stop sign
annunciator ( ) will display and the unit will stop
measuring. Press [Start/Stop] to resume measuring
from where you left off, or [RESET] to start from zero.
Manual Count Key — Each time you press this key, the
unit will show the count in the upper left of the display.
The unit will count from 1-199, and then will roll over
and continue counting from one. However, if you press
[Rcl] [Count], the accumulated total will display (for
example, 203) on the right side of the display. Press
[Del] [Count] to clear count to zero.
Multiple Area Storage Key — This key allows the
storage of up to nine different room areas (length and
width). After storing the first area values, pressing this
key will allow the storage of additional values. This
can be repeated for up to nine entries. This key is
also used to toggle between the different room areas.

8 — DigiRoller
™
Plus II
Height — Stores a height value (rolled or entered) for
calculating cubic volumes and wall areas. The height
value will carry over to the next room area, unless
changed by the user.
Volume — Calculates volume measurements from
entered or stored length, width, and height values.
AutoCount Mode — Places the unit in “AutoCount”
Mode, allowing you to program a fixed distance to be
automatically counted at each occurrence. The DigiRoller™
Plus II will automatically increase the count each time
it reaches the distance you have set (for example,
it will count the number of times you roll five feet),
and show the number of times it has measured this
distance on the upper left of the display.
Light Key — Turns the display back-light on or off.
Preferences
[Set] [Light] — Scrolls through the DigiRoller™ Plus II
Preference Settings, which include:
— Bell On/Off
— Wheel Size
— LCD Contrast Control
— Calibration and Percentage Calibration
(Detailed use of each of these preference settings are
discussed later in the guide.)

User’s Guide — 9
Using the Display
Clearing the Display
To clear the display, press the [RESET] key. This will clear the display
and place the DigiRoller™Plus II into a measuring mode.
Changing the Display Contrast Level
You can control the brightness of the display by adjusting the contrast
level setting.
1. Press the [Set] then [Light] keys to enter the preference setting.
2. Press the [Set] key to scroll to Preference 3, “Contrast” setting.
3. Press the [M+] or [M–] key to adjust the display contrast level
to the desired setting.
4. Press [RESET] to exit.

10 — DigiRoller
™
Plus II
Display Test/Annunciators
To perform a display test and light all annunciators, press [Rcl]
[Start/Stop]. Press [RESET] to clear the display test.
(1) Set symbol
(2) Count number
(3) Stop symbol
(4) Wheel Radius symbol
(5) Memory symbol
(6) Count/AutoCount symbols
(7) Fixed Distance symbol
(8) Area Number symbol
(9) Area Number indicator
(10) Total symbol
(11) Cubic symbol
(12) Width, Length, Height symbols
(13) Square symbol
(14) Units of measurement symbols

User’s Guide — 11
Changing Units of Measurement
The DigiRoller™Plus II can display and convert between the following
units of measure:
■Feet-Inch
■Decimal Feet
■Inches
■Yards
■Meters
■Acres (for displaying area values only)
You select your preferred unit of measure with the [Units] key.
Each press will advance through the above unit settings.
Any measurement on the display can be converted to the desired unit of
measure by pressing the [Units] key. For example, if the display shows:
and you would rather see the value displayed in inches, press the
[Units] key. You will see:
You can select different units of measurement for each measure conven-
tion (linear, square, cubic) just by pressing the [Units] key while display-
ing any linear, square or cubic value. The units of measurement you
choose will remain as they were last displayed until you change them
(even if you turn off the DigiRoller™Plus II).

12 — DigiRoller
™
Plus II
Turning the Bell On/Off
The DigiRoller™Plus II has a built-in bell sound, which you can turn
on or off. The bell is only heard when you are using the Count/Auto
Count functions. To turn the bell on or off, press the following keys:
1. Press [Set] then [Light] keys to enter the Preference Mode.
2. The display will show Preference 1, “Bell On” setting.
Press [M+] or [M–] if you wish to turn the bell sound off.
3. Press the [RESET] key to exit.
Note: You may have trouble hearing the bell in noisy outdoor
settings.

User’s Guide — 13
TAKING MEASUREMENTS
“Rolling” a Measurement
Here’s how to take a measurement with the DigiRoller™Plus II:
1. Turn the unit On by pressing the [On/Off] key. If the display
does not show zero (0), press the [Reset] key to clear the dis-
play.
2. Begin walking while rolling the DigiRoller™Plus II. You will see
the display registering your measurements.
Note: If you move the handle up or down while you are using
the unit, you will add or subtract a small distance (zero inches
to four inches) to any roll. For this reason, it is important to try
to keep the unit in the same position throughout the roll.

14 — DigiRoller
™
Plus II
3. When you are finished measuring, press the [Start/Stop] key.
4. If you wish to store the measurement, press [L] for length, [W] for
width or [H] for height. Press the [Start/Stop] key to begin a new
movement.
5. If you do not wish to store the measurement, you may either
press the [Start/Stop] key to continue from where you left off
or press [RESET] to start measuring from zero.

User’s Guide — 15
Storing / Recalling Values
The DigiRoller™Plus II has several keys that can be used to store and
recall values:
The DigiRoller™Plus II can also store and recall values in the [H],
[LxWxH], [AutoCount], and [Area#] keys.
To recall any of the values above, press the [Rcl] key and then press
the key that has the value you want to display. For example, to recall
the length that was rolled, press [Rcl] [L].
Storing Measurements in Permanent Memory
You can store rolled measurements in the standard calculator type
memory, by pressing the [M+] key after rolling. To subtract a mea-
surement from a previously stored value, press the [M-] key after
rolling. To recall the total stored in Memory, press [Rcl] [M+].
Note: This memory feature acts just like a standard, limited
calculator memory function; it will accumulate and total the
measurements added to it.

16 — DigiRoller
™
Plus II
Deleting Stored Measurements
To permanently delete a stored value, press the delete key [DEL] and
then the key that has the value you want to delete. Be careful when
pressing the [DEL] key, as it will permanently erase the stored value
of the next key pressed.
If you accidentally press the [DEL] key, press [RESET] to prevent any
stored value from being erased.
Using the Counter
The DigiRoller™Plus II has a manual “count” function that allows you
to count various items you may be tracking as you roll your measure-
ment (for example, parking spaces, fire hydrants, etc.).
When you want to count something, press the [Count] key. If the bell
is on, the unit will beep each time it is pressed and the count total in
the upper left corner of the display will increase by one. To subtract
a count, press the [Set] key then the [Count] key.

User’s Guide — 17
Taking Wall-to-Wall Measurements
Unlike other measuring wheels, the DigiRoller™Plus II has a built-in
function which enables you to measure true wall-to-wall distances (taking
into account the wheel’s radius when measuring up to a wall). The wheel
radius key will add the radius of the wheel to the measurement.
To measure a room accurately, press the wheel radius key
whenever your measurements begin or end against a wall
(see instructions below).
When you press this key, the DigiRoller™Plus II will add distance to the
measurement. Depending on your selected wheel size and measurement
units, the first and second presses of this key may not appear to be adding
equal distances due to display rounding. However, this is a display value
only; internal calculations will be accurate.

18 — DigiRoller
™
Plus II
Taking Area Measurements
Your DigiRoller™Plus II automatically calculates areas once you’ve
rolled a length and width. Remember, press [RESET] to begin each
new measurement.
1. Roll the first distance. Press the length key [L] and your rolled
distance will be automatically stored as the length.
2. Press [RESET]. Roll the second distance and press the width key [W].
3. Press [RESET]. Press the [L x W] key to calculate the area.