CAMDEN CV-WRX4 User manual

Page 1 of 2
CV-WRX4
Wiegand Receiver
INSTALLATION INSTRUCTIONS
CV-WRX4 receiver is designed for use with Camden
CV-WTX2 transmitters. The transmitter signal is codied in two
dierent protocols according to its conguration: Wiegand 26
and Wiegand 37. The receiver provides facility codes 1 to 255
by DIP switch J9 using 8 bit binary conguration.
2. INSTALLATION AND CONNECTIONS
Attach the rear part of the enclosure to the wall using the
plugs and screws supplied. Pass the cables through the
grommet of the enclosure. Connect the power cables to the
terminals marked on the mother board, as Indicated.
Mount the receiver cover and pass the cables and the
antenna through it.
3. OPERATING
Conguration and connection for the dierent protocols.
Protocol Power
Supply
Signal
Outlet
SW1
Protocol Format
Wiegand
26 + - D0 and D1 O 8 bits facility code + 16 bits credential ID number
Wiegand
37 + - D0 and D1 ON -
Power Supply 12V DC ( 9VDC - 21VDC)
Frequency 868.35 MHz
Consumption
Standby / Operating 14mA / 36mA
Operating
Temperature -4°F to +185°F (-20°C to +85°C)
IP Rating IP54 (IP65 with cable plug installed)
Dimensions 3 1/4" W x 7 3/8" H x 1 5/8" D
(82mm x 187mm x 42mm)
1. TECHNICAL CHARACTERISTICS
Note: To use other protocols, contact Camden.
Operations
The green power on LED will illuminate when power is
provided. The red signal LED will illuminate for the duration it
receives the message from the transmitter.
If the red LED does not illuminate when the transmitter
button is pressed, the receiver is not receiving the
transmission signal from the transmitter. Reduce the distance
to the receiver, and verify the transmitter is working as
suggested
Refer to Facility Code DIP switch table to select the value of
facility code to be sent from the receiver.
+
-
12V dc supply
12V dc supply
CH2
Decoded signal output (D0 Wiegand)
Decoded signal output (D1 Wiegand)
Decoded signal output (D0 Wiegand)
Decoded signal output (D1 Wiegand)
J9
1 2 3 4 5 6 7 8
ON
LSBMSB
128 64 32 16 8 4 2 1
The DIP switch posions will provide a
facility code = 34. SW#3 = 32. SW#7 =2.
The total = 32 + 2 = 34
The DIP switch positions set
the facility code.
For example:
34. SW#3 = 32. SW#7 = 2.
The total = 32 + 2 = 34
THIS PACKAGE INCLUDES:
(1) CV-WRX4 Receiver
(2) #6 x 1-1/4" Screws
(2) #6 Wall Plugs
(1) Cable Plug
CH1

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 2 of 2
CV-WRX4 WIEGAND RECEIVER
INSTALLATION INSTRUCTIONS
File: 40-82B267-CV-WRX4-Wiegand.-
Receiver_Manual.indd
Rev.: May 10th 2021
Part No.: 40-82B267
COMPLIANCE
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Operation Is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
6. IMPORTANT APPENDIX
• This equipment must be installed in a vertical position, and rmly axed to the building structure.
• This equipment is designed for use as a remote control for overhead doors and access control. Its use is not guaranteed
for directly activating any other equipment dierent to that specied.
• Camden reserves the right to modify equipment specications without prior notice.
5. USE OF THE RECEIVER
This receiver interface is designed to work with remotes to control overhead doors or barrier gates. Their use is not
guaranteed for directly activating any other equipment.
Camden reserves the right to modify equipment specications without prior notiice.
1 5/8"
[42mm]
1/16"
[2mm]
5/8"
[15mm]
3 1/4"
[82mm]
5"
[127mm]
7 3/8"
[187mm]
Ø1/8"
[4mm]
Mounting Hole
2 Places
3 7/8"
[97mm]
1 5/8"
[41mm]
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference hat may cause undesired operation.
FCC ID: U5Z-CONNECT4CC
4. CV-WRX4 WIEGAND RECEIVER FRONT, SIDE AND BACK VIEW
SIDE VIEW
FRONT VIEW BACK VIEW