CAMDEN Lazerpoint RF RX-90v2 User manual

Page 1 of 7
Lazerpoint™ RF RX-90v2
Advanced Single Relay Receiver
INSTALLATION INSTRUCTIONS
Door Activation Devices
1-
THIS PACKAGE INCLUDES:
1. DESCRIPTION
CM-RX-90v2 receivers can be paired with Lazerpoint™ or
Kinetic™ transmitters, switch selectable.
Kinetic™ by Camden is an advanced 900 MHz 'power harvesting'
wireless system that uses the energy created by the operation
of the switch to power the wireless transmitter.
This Kinetic™ transmitter is available with the following push
plate switches: CM-45K and CM-46K.
Camden Lazerpoint™ Radio Controls comprise the following
models:
• CM-TX-9 Wall switch ready transmitter
• CM-TX-99 Plug-in transmitter
• CM-TXLF 1, 2 & 4 button fob transmitters
• CM-RX-90v2 Advanced single relay receiver
• CM-RX-91 Basic single relay receiver
• CM-RX-92 Full function (dual relay) receiver
Camden Lazerpoint™ RF is the rst system designed to address
the specic needs of the Automatic Door industry. Unlike typical
“garage door” RF, Camden’s Lazerpoint™ operates at 915 MHz
frequency to “cut through” the noise and clutter, and penetrate
typical building materials to ensure a reliable installation every time.
Three receiver models are offered – the basic single relay RX-91,
the full function RX-92 and the advanced single relay RX-90v2. The
RX-90v2 offers 3 operating modes including delayed, no delay and
latched.
Camden CM-RX-90v2 supports both Lazerpoint™ RF and
Kinetic™ by Camden transmitters.
Camden CM-RX-90v2 features a convenient terminal block,
visual relay status, and 40 code memory with push and learn
technology.
2. FEATURES
• 3 Modes of Operation:
- Delayed (1 - 15 Seconds)
- No Delay (1 – 30 Seconds)
- Latching
• Adjustable Range: -3' - 300'
• 40 Transmitter capacity, either Lazerpoint™ or Kinetic™ either
delayed, non-delayed or both
• Form ‘C’ Relay Output
• 12/24V AC/DC operation
• 915 MHz Lazerpoint™ or Kinetic™ Technology
• Small Size: 2 5/8”H x 1 1/2”W x 13/16”D
(67mm x 38mm x 21mm)
3. SPECIFICATIONS
Operating Voltage 12/24V AC/DC
Current Draw 23 mA nominal @ 24 VAC
43 mA maximum @ 24 VAC
Response Time 30 – 200 ms
Memory Delay &
No Delay 40 transmitters total
LED’s Indicate: relay status; learn mode;
erase mode & potentiometer position
Output 1 x SPDT Relay contact
Rating 3 amps @ 30 VDC
Operating Time 1 – 30 seconds
Delay Time 1-15 seconds
Frequency 915 Mhz.
Mounting 2 # 4 screws at 3” centers,
or Velcro (supplied)
Enclosure Clear plastic case
Dimension 2 5/8”H x 1 1/2”W x 13/16”D
(67mm x 38mm x 21mm)

LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 2 of 7
4. INSTALLATION
MOUNTING
The RX-90v2 receiver is designed to mount inside the automatic
door header. Screw holes are located at each end of the receiver
case, or the included velcro may also be used to hold it securely.
For dimensional information refer to RX-90v2 electrical and
mechanical Drawing on Page 4.
WIRING
Note: Do not use the Kinetic/Lazerpoint RF system as a Safety
device!!. If safety devices are used, always wire them directly to
the operator control box.
Refer to the RX-90v2 Wiring Diagram on Page 5, and wire the
receiver as follows:
Wire the device (electric lock / operator) to the Relay output -
terminal 3 is N.O. 4 is Common, and 5 is N.C.
Connect 12 or 24 Volt AC or DC to terminals 1 & 2 on the receiver.
(The terminals are not polarity sensitive)
Terminal Description
1Power in
2Power in
3Normally Open
4Common
5Normally Closed
5. SET-UP INSTRUCTIONS
STEP 1
Learning the Transmitter(s) to the Receiver
A receiver can have up to 40 transmitters paired with it. The
transmitter can be paired as Kinetic™/ Lazerpoint™ delayed,
non-delayed or a combination of both, making RX-90v2 ideal
for bi-directional door sequencing.
Set the RF Transmitter Type
Set DIP2 to ON Kinetic™, DIP2 to OFF Lazerpoint™
Learning the Transmitter in Delayed Mode
Set DIP1 to ON.
Press the PB1 button using a small blunt object such as a small
blade screwdriver or similar. Within 10 seconds, press the switch
connected to a TX-9 transmitter or a button on a Lazerpoint™
FOB or Kinetic™ switch. The Green LED Array will ash to conrm
enrolment. Repeat with any additional transmitters. Pressing
the learned transmitter again will signal the receiver that you are
nished programming and the LED will ash rapidly.
Pressing the transmitter a third time will activate the relay and
the LED, and also the device connected to the relay contacts
after the delay time set by POT1.
If you wait longer than the 10 second period, the receiver will
time out of Learn Mode and revert back to standby.
Learning the Transmitter in No-Delay Mode
Set DIP1 to OFF
Press the PB1 button using a small blunt object such as a small
blade screwdriver or similar. Within 10 seconds, press the switch
connected to a TX-9 transmitter or a button on a Lazerpoint™
FOB or Kinetic™ switch. The Green LED Array will ash to conrm
enrolment. Repeat with any additional transmitters. Pressing
the learned transmitter again will signal the receiver that you are
nished programming and the LED will ash rapidly.
Pressing the transmitter a third time will activate the relay and
the LED, and also the device connected to the relay contacts.
If you wait longer than the 10 second period, the receiver will
time out of Learn Mode and revert back to standby.
STEP 2
Adjustments
The delay before operate and the relay On-Time are controlled
by POT1.
Delayed Mode
The RX-90v2 has a delay before operate timer.
Set DIP1 to ON.
Adjust POT1 clockwise to increase the delay timer from 0 to
15 seconds. The LED will light and become brighter as the
delay time is increased and become dim as the delay time is
decreased. The LED starts to ash once the maximum delay
time has been reached. Back off the delay time until the LED is
solid again for maximum delay time.
No-Delay Mode
The RX-90v2 can be adjusted to activate the output relay
without a delay. The relay On-Time is adjustable from 1 to 30
seconds.
Set DIP1 to OFF.
Adjust POT1 Clockwise/counterclockwise to adjust the relay
On-Time (1 to 30 Seconds). To increase the time, turn the pot
clockwise, or for minimum time, turn the pot counterclockwise.
The LED will light and become brighter as the Relay On-Time is
increased. The LED starts to ash once the maximum On-Time
2
ON
1
POT1 PB1
DIP 1 DIP 2

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 3 of 7
File: Lazerpoint RF RX-90v2
Manual .indd Rev2
Revised: 15/08/2019
Part No.: 40-82B212
has been reached. Back off the POT until the LED is solid again
for maximum On-Time.
Latching Mode
The RX-90v2 has a latching mode. Activating the transmitter will
latch the output relay ON. Activating the transmitter a second
time will latch the Relay OFF.
DIP1 can be set to either ON/OFF.
Adjust POT1 clockwise until the LED starts to ash. The RX-90v2
is in latching mode at this point. To remove latching mode, turn
POT 1 counter clockwise until the LED is solid again.
Note: Latching mode disables delayed mode. Transmitter
programmed as delayed mode will work as latching mode
transmitter.
Signal Strength Adjustment
For the most reliable, consistent operation, leave the signal
strength at full power. Camden RX-90v2 receiver has an
adjustment RF range. The range can be adjusted from a few feet
to full range (300 ft. LOS)
To adjust the RF range:
1. Press PB1 to enter pairing mode.
2. Press PB1 again until the LED ickers 3 times. This places
the receiver in RF range adjust mode.
3. Adjust POT1 to adust the RF range. CW to increase the
range, CCW to decrease the range.
4. Press a paired transmitter to test the range as it is being
adjusted.
5. Once the desired range is set, Press and hold PB1 until the
LED ickers 3 times. The transmitter is now back in pairing
mode. Either wait for the receiver to time out or press a
paired transmitter to exit pairing mode.
After adjusting the range you MUST adjust POT 1 for relay
timing at this point based on the mode (delay or no-delay).
STEP 3
DELETING TRANSMITTERS
Delay Mode Transmitters
Set DIP1 to ON.
Pressing and holding PB1 for 8 seconds will delete all
transmitters delay mode. The LED will ash rapidly for
4 seconds to indicate erasure of the codes.
No Delay Mode Transmitters
Set DIP1 to OFF.
Pressing and holding PB1 for 8 seconds will delete all
transmitters no delay mode. The LED will ash rapidly for
4 seconds to indicate erasure of the codes.
Note that individual removal of specic codes is not possible.
6. WARRANTY
Camden Door Controls guarantees the Lazerpoint™ RF to be
free from manufacturing defects for 3 years from date of sale.
If during the rst 3 years a Lazerpoint™ RF component fails to
perform correctly, it may be returned to our factory where it
will be repaired or replaced (at our discretion) without charge.
Except as stated herein, Camden extends no warranties
expressed or implied regarding function, performance or
service.
NOTE: Batteries are exempt from this warranty!

LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 4 of 7
IC & FCC INFORMATION FOR USERS
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This radio receiver has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent receveur radio a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci dessous et ayant un gain admissible
maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation
de l’émetteur.
Antenna Specication
Model: Camden Lazerpoint Proprietary PCB Antenna
Center Frequency: 915MHz
Recom. Freq. Range: 903-928MHz
Wavelength: ¼ Wave
Peak Gain: 0dBi
Impedance: 50-ohms
Connector: 2-pin Header
Oper. Temp. Range: -40° to +85°C
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modications made to this equipment not expressly approved by Camden Door Control could void the user’s authority to operate the equipment.

LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 5 of 7
CX-RX-90 Electrical and Mechanincal
CAMDEN DOOR CONTROLS
SCALE: NONE
DRAWING No: FILE NAME: CM-RX-90_Mech.ai
DRAWN BY: J LEWIS DATE: 09/14/17 REVISED:
5502 Timberlea Blvd. Mississauga, Ontario L4W 2T7
POT1 PB1
25
8"
[67mm]
3"
[77mm] 33
8"
[85mm]
13
16 [21mm]
"
11
2" [38mm]
CM-RX-90_Mech
WIRE COLOR DESCRIPTION
RED RED BLUE GREY ORANGE
POWER IN
POWER IN
NORMALLY OPEN COMMON
NORMALLY CLOSED
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1

LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 6 of 7
Door Operator #1
TO OPEN
PUSH
Switch
& TX-9
CM-RX-90 Basic Wiring Diagram
CM-RX-90_Wiring_1.ai
JLEWIS 09/14/17
A
1
2
3
4
5
6
7
8
87654321
NEXT ASSY USED ON
APPLICATION
MATERIAL
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO. REV
SCALE: 1:1
UNLESS OTHERWISE SPECIFIED:
SHEET 1 OF 1
DO NOT SCALE DRAWING
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/64
ANGULAR: MACH 0.5 BEND TWO PLACE DECIMAL 0.010 THREE PLACE DECIMAL 0.005
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED.
5502 Timberlea Blvd. Mississauga, ON Canada L4W 2T7
Tel: [phone]
www.camdencontrols.com
D
C
B
A
B
C
D
Grey
12-24V
AC/DC
Power
Blue Red
Red
POT1 PB1
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1
Set the Protocol with DIP2 ON= KineticTM OFF= LazerpointTM Learning the Transmitter in Delayed Mode Step 1 - Set SW1 to ON. Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press the switch connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat with any additional transmitters. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Learning the Transmitter in No-Delay Mode Step 1 - Set SW1 to OFF Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press the switch connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat with any additional transmitters. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby.

LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Page 7 of 7
Door Operator #2
TO OPEN
PUSH
Switch
& TX-9
CM-RX-90 Vestibule Wiring Diagram
CM-RX-90_Wiring_2.ai
JLEWIS 09/14/17
A
1
2
3
4
56
7
8
876
5
4321
NEXT ASSY USED ON
APPLICATION
MATERIAL
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO. REV
SCALE: 1:1
UNLESS OTHERWISE SPECIFIED:
SHEET 1 OF 1
DO NOT SCALE DRAWING
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL: 1/64
ANGULAR: MACH 0.5
BEND
TWO PLACE DECIMAL
0.010
THREE PLACE DECIMAL
0.005
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED.
5502 Timberlea Blvd. Mississauga, ON Canada L4W 2T7
Tel: [phone]
www.camdencontrols.com
D
C
B
A
B
C
D
12 - 24 V
AC/DC Power
Door Operator #1
12 - 24 V
AC/DC Power
TO OPEN
PUSH
PUSH
TO
OPEN
PUSH
TO
OPEN
Vestibule
Switches
&TX-9 's
1
2
3 4
Switch
& TX-9
Receiver #1 Receiver #2
Red
Red
Blue
Grey
Red
Red
Blue
Grey
POT1 PB1
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1
POT1 PB1
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1
Programming the Transmitters into the Receivers: Set the Protocol with DIP2 ON= KineticTM OFF= LazerpointTM Receiver #1 Learning Transmitter #2 into Delayed Mode Step 1 - Set SW1 to ON (Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #2 . The Green LED Array will ash to conrm enrolment. Step 3 - Pressing switch #2 again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 4 - Adjust POT 1 for the delay time (1 - 15 Seconds). Learning Transmitters #1 and #4 into No-Delay Mode Step 1 - Set SW1 to OFF (No Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #1 connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat step #2 for switch #4. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 5 - Adjust POT 1 for the relay Hold time (1 - 30 Seconds). Receiver #2 Learning Transmitter #1into Delayed Mode Step 1 - Set SW1 to ON (Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #1. The Green LED Array will ash to conrm enrolment. Step 3 - Pressing switch #2 again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 4 - Adjust POT 1 for the delay time (1 - 15 Seconds). Learning Transmitter s #2 and #3 into No-Delay Mode Step 1 - Set SW1 to OFF (No Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #2 connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat step #2 for switch #3. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 5 - Adjust POT 1 for the relay Hold time (1 - 30 Seconds).