Camden Lazerpoint rf rx-92 User manual

Lazerpoint™ RF RX-92

Full-Function Receiver

Installation Instructions

Section 1

General Description

Camden Lazerpoint™ Radio Controls comprise the following

models:

CM-TX-9 Wall switch ready transmitter

CM-RX-91 Basic Receiver

CM-RX-92 Full function (dual relay) Receiver.

This instruction manual covers the TX-9 and RX-92 models

as well as the plug-in daughterboard’s, and related

accessories.

Camden Lazerpoint™ RF is the ﬁrst system designed to

address the speciﬁc needs of the Automatic Door industry.

Unlike typical “garage door” RF, Camden’s Lazerpoint™

operates at 915 MHz frequency to “cut through” the noise

and clutter, and penetrate typical building materials to

ensure a reliable installation every time.

TX-9 transmitters utilize readily available AAA batteries,

and special circuitry assures long life. A proprietary piezo

sounder is used to annunciate low battery, battery level,

and “stuck switch” conditions.

Two receiver models are offered – the basic single relay

RX-91, and the full function RX-92. The RX-92 offers 6

operating modes including dual independent channels,

latching, and bi-directional sequencing.

Both receivers can be ﬁtted with plug-in daughterboard’s

ensuring compatibility with older RF technologies. Up to two

such boards may be installed at one time, simultaneously

allowing the receiver to work with three different frequencies

– another Camden exclusive.

Both receiver models feature convenient terminal strip

connections, visual signal strength indicators, and 40 code

memory with push-and-learn technology.

Section 2

Installation

Mounting

The TX-9 is designed to mount behind a switch in a wall-

box, post, or other suitable enclosure. Double sided tape is

used to attach the circuit board and battery holder securely

to the enclosure. Even though the circuit board is conformal

coated, care should be taken to ensure the transmitter does

not get wet.

The RX-92 receiver is designed to mount inside the automatic

door header. Screw holes are located at each end of the

receiver case, or the included velcro may also be used to

hold it securely.

For Dimensional information refer to RX-92 Electrical and

Mechanical Drawing on Page 5.

Wiring

Wiring of this unit is dependant on the application and mode.

Determine the appropriate mode, and then proceed to the

section and drawing indicated.

Note: Do not use the Lazerpoint RF system as a Safety

device!!. If safety devices are used, always wire them directly

to the operator control box.

Section 3

Set-up Instructions

The RX-92 has two relays, and three potentiometers with two

1 – 30 second adjustable Hold time (or delay-on-release)

and a 1 – 15 second delay-on-activate for the second relay.

The 4-position dip switch selects from one of 6 different

operating modes.

Dip switch #4 controls the display of LED 1 & LED 2. When

set to OFF, it will display the operation of the associated

relay(s). When set to ON, it will blink a count to indicate the

received signal strength. To facilitate set-up, set to OFF.

Page 1 of 13

Page 2 of 13

Lazerpoint™ RF RX-92 Full-Function Receiver Installation Instructions

Step 1

Select Operating Mode

Select the desired operating mode by setting the ﬁrst 3

dip switches as follows:

Mode 1 Dual independent outputs

Operates as a two channel receiver.

Refer to Diagram 1, Page 6

Mode 2 Switching Network

Also known as a switching network or make/

break relay,usethismodewithadooroperator&lock

Refer to Diagram 2, Page 7

Mode 3 Vestibule Sequencing

Select if you want to sequence two doors in both

directions, using just one RX-92 receiver (requires

two conductors to the second door)

Refer to Diagram 3, Page 8

Mode 4 Vestibule Sequencing

Select if you want to sequence two doors in both

directions, using two RX-92’s and no wiring between

operators

Refer to Diagram 4, Page 9

Mode 5 Latched Mode A

Access Control application. A transmitter

signal learned into channel 1 will latch Relay 1. While

relay 1 is latched, a transmitter learned into channel

2 will activate relay 2. When channel 1 is in the off

state, the RX-92 will ignore channel 2 inputs.

Refer to Diagram 5, Page 10

Mode 6 Latched Mode B

Freight Door application. In this mode a transmitter

will active relay 1 for an adjustable time, then latch

relay 2. Relay 2 stays latched until another transmitter

signal is received then drops out immediately.

Refer to Diagram 6, Page 11

Step 2

Connections

Refer to the TX-9 Installation Drawing (supplied with

Transmitter) for the following connections.

Connect the transmitter wires to the activating switch (N.O.

momentary dry contacts). Insert 2 fresh AAA alkaline

batteries (provided) into the battery holder. Press the switch

and observe the red LED to ensure proper transmission.

Test the transmitter by pressing and holding the switch for 5

seconds. The piezo speaker should sound 5 beeps, meaning

the batteries are at full capacity. This is the Battery Gauge™

feature.

If the piezo beeps only 1 - 3 times, you should change the

batteries for fresh (new) ones.

Now press and hold the switch for 15 seconds. The piezo

should now make a distinctive hi-low sound. This signal will

sound for 6 seconds, then turn off for a minute, then sound

again. This is the “stuck switch indicator” feature. Repeat for

additional transmitters.

Wire the receiver according to the speciﬁc application

drawing. Generally however, wiring is as follows:

Wire the ﬁrst device (electric lock / operator) to Relay 1 output

- terminal 3 is N.O. 4 is Common, and 5 is N.C.

Wire the second device (electric lock or operator) to Relay 2

output - Terminal 6 is N.O., 7 is Common, and 8 is N.C.

Connect 12 or 24 Volt AC or DC to terminals 1 & 2 on the

receiver. (The terminals are not polarity sensitive).

Step 3

Learning the Transmitter(s) to the Receiver

The procedure for learning of transmitters is dependant on

the speciﬁc operating mode. Please refer to the applicable

wiring diagram for exact instructions.

General instructions are as follows:

To learn the transmitter into the receiver, press the PB1 (or

PB2) button using a small blunt object such as a small blade

screwdriver or similar. Within 10 seconds, press the switch

connected to a TX-9 transmitter. You should then see the

Green LED display light on the receiver to indicate the TX-9

has been received and learned. Repeat with any additional

transmitters. Pressing the learned transmitter again will

signal the receiver that you are ﬁnished programming and

LED’s 1 & 2 will ﬂash, in an alternating sequence. Pressing

the transmitter a third time will activate the relay and

corresponding LED, and also the device connected to the

relay contacts.

If you wait longer than the 10 second period, the receiver will

time out of Learn Mode and revert back to standby. The LED

will then ﬂash to indicate the number of transmitters learned

into the receiver.

Step 4

Adjustments

The RX-92 has two relay hold timers (delay-on-release) of

1 – 30 seconds each (Pots 1 & 3). There is also a delay-on-

operate time for relay two (Pot #2)

To increase time, turn the pot clockwise, or for minimum

time, turn the pot counter-clockwise.

Always walk-test the installation and adjust the timers

to suit.

Page 3 of 13

Lazerpoint™ RF RX-92 Full-Function Receiver Installation Instructions

Step 5

Testing Signal Strength

By setting Dip Switch #4 to ON, you can display the signal

strength of the transmission from a TX-9 transmitter. The

beneﬁt is the installer will be able to determine that the

transmitter or receiver is in the best possible location and

that the transmission is not being hindered by possible

interference.

To display signal strength, set Dip switch #4 ON.

Activate the transmitter, and observe the number of ﬂashes

of LED 1. One or two RED ﬂashes indicates poor reception,

and it is suggested to move the transmitter or receiver until

3 to 5 GREEN ﬂashes are observed. Sometimes moving the

transmitter only a few inches one way or another will make a

signiﬁcant difference. Four or ﬁve ﬂashes are ideal.

Step 6

Deleting Transmitters

Pressing and holding either PB1 or PB2 for 8 seconds will

delete all transmitters. The LED Array will ﬂash rapidly for

4 seconds to indicate erasure of the codes. Note that

individual removal of speciﬁc codes is not possible at this

time.

Step 7

Adding Daughterboard’s

A unique feature of Camden’s Lazerpoint RF is the ability

to add one or two daughterboard’s, extending compatibility

to older technologies. This ability to work with additional

frequencies also allows the user to utilize hand-held

transmitters as well as wall-switch-ready transmitters.

The daughterboard’s may be factory or ﬁeld installed. Please

see Drawing DRG-RX-DB (page 12) for detailed installation

instructions.

! Remember to take reasonable care to avoid static

electricity whenever handling circuit boards. !

The daughterboards may be identiﬁed by the model number

and antenna colour, as shown in the chart below:

Once installed, the learning of transmitters on above

frequencies is identical to the TX-9 transmitter. Also, the

40 code memory limit includes all transmitters, even those

learned in on the daughterboards.

Step 8

Using CM-RFCT Cable tool

Since the LED’s may be difﬁcult to see once the RX-92 is

installed, a 33” long plug-in cable tool is available.

The CM-RFCT Cable Tool plugs into the opening on the side of

the receiver, and allows the installer to view LED’s mounted

on the free end. Pairs of LED’s mounted on both sides of the

cable increase visibility.

Display status is dependant on Dip switch 4 setting. Turn OFF

to view relay status, and turn ON to view the Signal Strength.

When installation is complete, simply unplug the cable tool,

coil and save for another job.

Model #

RX-DBB

RX-DBO

RX-DBR

RX-DBW

Frequency

300 MHz

318 MHz

390 MHz

433 MHz

Antenna

Blue

Orange

Red

White

Page 4 of 13

Lazerpoint™ RF RX-92 Full-Function Receiver Installation Instructions

Section 4

Technical Data

Model TX-9 Transmitter

Frequency: Operates in the 902 – 928 MHz

ISM Band

Codes 1 million unique (20 bit) codes

Size 2 ¼” L x 5/8” W x 3/8” H

Mounting Double sided foam tape

Switch Connection 2 x 10” leads with ¼”

quick disconnect terminations

Built-in Piezo sounder Used for Low Battery status,

Battery Gauge™, and Stuck

Switch indicator.

Power 2 x AAA alkaline batteries

Battery life Minimum 500,000 operations

Range Over 500 ft (open area)

Temperature rating -40 to 185 F (-40 to +85 C)

Model RX-92 Receiver

Size 3 ½” L x 2” W x 1” H

Mounting 2 # 8 screws at 4” centers,

or Velcro (supplied)

Enclosure Clear plastic case

Operating voltage 12 / 24 Volts, AC / DC

Current Draw 23 mA nominal @ 24 VAC

63 mA maximum @ 24 VAC

+ 5 mA per RF module

Response time 30 – 200 ms

Operating Modes Via 4 dip-switches

Memory 40 transmitters

LED’s Indicate: relay status;

signal strength; learn mode;

erase mode & potentiometer

position

Outputs RX-92 – 2 x SPDT relays

Relay contact rating 3 amps @ 30 VDC

Time Delays 3 potentiometers:

Relay1 D.O.R. = 1 – 30 sec

Relay 2 D.O.O = 1 – 15 sec

Relay 2 D.O.R. = 1 – 30 sec

Electrical Life 1 x 105 minimum

Temperature rating -40 to 185 F (-40 to +85 C)

Certiﬁcations ·FCC Part 15 Compliant

·Canada RSS/CNR210:1078

1032 061A

·Meets: IEC60601-1-2:2007

Patent Pending

Accessories:

Plug-in daughterboard’s extend capability with other

frequencies. Refer to the following chart:

Daughterboard Operational Antenna

Model # Frequency Colour

RX-DBB 300 MHz Blue

RX-DBO 318 MHz Orange

RX-DBR 390 MHz Red

RX-DBW 433 MHz White

CM-RFCT: A 33” long cable-tool for high visibility of relay

status and signal strength

Section 5

Warranty

Camden Door Controls guarantees the Lazerpoint

RF (TX-9, RX-91,or RX-92 models) to be free from

manufacturing defects for 3 years from date of sale.

If during the ﬁrst 3 years a Lazerpoint RF component fails to

perform correctly, it may be returned to our factory where it

will be repaired or replaced (at our discretion) without charge.

Except as stated herein, Camden extends no warranties

expressed or implied regarding function, performance or

service.

NOTE: Batteries are exempt from this warranty!

Questions?

Call us toll-free at 1-877-226-3369

Page 5 of 13

Page 6 of 13

Page 7 of 13

Page 8 of 13

Page 9 of 13

Page 10 of 13

Page 11 of 13

Page 12 of 13

Lazerpoint™ RF RX-92 Full-Function Receiver Installation Instructions

Page 13 of 13

Push Buttons Key Pads Strikes Magnetic Locks Key Switches Relays & Timers Access Control

File: Lazerpoint RF RX_92

Instructions.doc -Rev. 3

Revision: 19/05/2016

Part No.: 40-82B122

5502 Timberlea Blvd.,

Mississauga, ON Canada

L4W 2T7

www.camdencontrols.com

Toll Free: 1.877.226.3369

IC & FCC INFORMATION FOR USERS

IC: 8725A-RX9192

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1) l’appareil ne doit pas produire de brouillage;

2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

This radio transmitter (8725A- RX9192) has been approved by Industry Canada to operate with the antenna types listed below with the maximum

permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Le présent émetteur radio (8725A- RX9192) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci dessous et ayant

un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits

pour l’exploitation de l’émetteur.

Antenna Specication

Model: Camden Lazerpoint Proprietary PCB Antenna

Center Frequency: 915MHz

Recom.. Freq. Range: 903-928MHz

Wavelength: ¼ Wave

Peak Gain: 0dBi

Impedance: 50-ohms

Connector: 2-pin Header

Oper. Temp. Range: -40° to +85°C

FCC ID: 2AHAB-RX9192

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Changes or modications made to this equipment not expressly approved by Camden Door Control could void the user’s authority to operate the equipment.

Table of contents