Campania International Zen III FT-242 User manual

FT
-
242 ZenIII Fountain
R
evised
May3, 2018
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
Pump KitPartsList
PK140 pump (1)
#10 stopper(1)
Approx.7”length of1/2”blacknon-kinktubing (1)**
Approx.2”length of5/8”clearvinyltubing (1)**
2”length of½”CPVCpipe(1)**
Wedges(2)
Hose clamps(3)*
*Hoseclamps maybe used asflow restrictors
**Tubing hasbeen preassembled
FOUNTAININFORMATION:
Thisfountain holdsapproximately1.5gallonsof water.
Thisfountain usesasmallfountain cover.
(FTNCOV-SM)
Norefill device orsubmersible lightsare suggested for
thisfountain
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
OEMPF140 - 140GPH Pump
6FTcord length

FT
-
242 ZenIII Fountain
R
evised
May3, 2018
Assemble your fountainon alevel surface capable ofholding aminimumof150
poundswithanapproximate1squarefootfootprint.
FT-242B(118 lbs)
20.5”Wx18”H
FT-242A(16 lbs)
16.5”Wx3”H
1. Position thebasin(FT-242B) wherethe
fountainistobeinstalled, ensuring that it is
level.
2. Assemble thepumpkit.
a. NOTE:All pumpscomewith1
adapter alreadyinsertedintothe
pumpand 2adapterssecured tothe
power cord.
i. Thisfountain usesthe largest
adapter provided.
b. Using ahoseclamp, attachthe1/2”
non-kinktubing tothepumpoutlet.
c. Place thestopper around thepumpcord
approximately6inchesfromthepump.
3. Feedthepumpcordall thewaythrough the
hole and thechannel inthebasin(FT-262B)
toensurethefountainwill belevel.
a. Lineup thesplit inthestopper withthe
direction that thechannel under the
basingoes.
4. FIRMLY press thestopper intothehole
evenly.
5. Holding thewaterfeature(FT-242A)over
thebasin(FT-242B), inserttheCPVCend of
thetubing assemblyintothecoupling
protruding fromthebottom.
6. Center thewater feature(FT-242A) into
basin(FT-242B).
a. Turnthefeaturetocoil thetubing as
you lower itintoposition.
7. Fill thefountainwithwater.