Campania International Meridian FT-325 User manual

FT
-
3
25
MeridianFountain
Two people are recommended for the installation ofthisfountain!
PumpKitParts List
PK120-FG PumpandLight Kit (1)*
#7 stopper(1)
2”lengthof PermaGum
8”length1/2”non-kinkhose(1)
O-Ring(1)
Wedges(2)
Hoseclamps(1)
* DoNOTpreassemblethepumpandlightkit
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video. https://youtu.be/J6GjxwVAIyU
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
FOUNTAININFORMATION:
Thisfountain holdsapproximately3-5 gallonsof water.
Thisfountain usesasmallfountain cover.
(FTNCOV-SM)
Norefill device orother submersible lightsare
suggested forthisfountain
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
120 GPH lowvolt Pumpw/separatelight and transformer
10 FTcord length
Revised December 11, 2018
SHOP NOW
SHOP NOW

FT
-
3
25
MeridianFountain
Two people are recommended for the installation ofthisfountain!
Assemble your fountainonalevel surface capable ofholdingaminimumof225 poundswithanapproximate 1squarefootfootprint.
FT-325C (209lbs)
24.75”Wx33.25”H
FT-325A(6lbs)
13”Wx4.25”H
Light /Spout
Pump
FT-325B (4lbs)
5”Wx2.5”H
PowerCord
Transformer
1. Position thebasin (FT-325C)where thefountain is to beinstalled, ensuringthatit is
level.
2. Usingburlap oran old towel, laythewater featurebowl(FT-325A) upsidedown
and propped up on theedgeofthebasin (FT-325C).
3. Place theO-Ringaround the Light/Spout. TheO-
Ringwill secure the Light/Spout in place and allow
forthewater to flowcorrectlyin thefountain.
(IMAGE RIGHT)
4. Attach thenon-kink tubingto the Light/Spout.
5. Feed the Light/Spout cord and non-kink tubingthrough theholein thetop ofthe
water featurebowl(FT-325A).
a. Note:There is anotch onthesideoftheholein the
bowlis to accommodatethecord (IMAGE RIGHT).
6. Carefullypress the Light/SpoutwithO-Ring into theholeat
thetop oftheholein thebowl.
a. Note:Useaflathead screwdriver orsimilar toolto
press theO-Ringdeeper into theholearound the Light/Spout.
7. Attach the Pump to thenon-kink tubingwith ahoseclamp.
8. Feed bothcords throughthePVCpipein thebasin (FT-325C)and outofthe
channelunderneath.
a. Note1:Bindingthe2 cords togetherwith azip tie, twist
tie, orstringmakes this step easier.
b. Note2:Besure to placeoneplugbelowtheother. Ifyou
tryforcingboth plugs through atthesametime, theywill
notfit. (IMAGE RIGHT)
9. UsingthePermaGumprovided, wraparound each cord, then placeit into the
stopper with theextra PermaGumfillingtheslit and cuttingawayanyexcess.
10. FIRMLY press thestopper into theholeevenly.
a. Note:Usingthehandleofascrewdriverorhammer works bestto press the
stopper in place.
11. Fit pump and lightcords through theslit in thepump cover
(FT-325B).(IMAGE RIGHT)
12. Besureto levelthecover(FT-325B)in thecenterofthe
basin (FT-325C).
13. Center and levelthebowl(FT-325A)on thepumpcover (FT-325B).
14. Connectthe Pumpand Light/Spout cords to theregular Power Cord.
15. Connectthe Power Cord and Transformer.
Revised December 11, 2018
SHOP NOW