Campania International FT-295 User manual

FT-286A
8.25”x21”x15.5”
171lb
FT-286B
4”x17.5”x1”
6lb
FT-286C
6.75”x21”x6.75”
20lb
FT-286D
1.25”x7”x4.75”
4lb
FT-286F
22.25”x15”x15”
140lb
FT-288E
28”x16.50”x3”
37lb
FT-295 Falling Water 1 Fountain
(6 Pieces)
Components and Parts List
Revised July 11, 2016
Pump Kit and Parts List
Copper spiller
2 oz Silicone tube
12” length 5/8” non-kink hose (1)
Hose clamps(3)
Note: Clamps can be used as flow
restrictors
525 GPH Pump(1)
Wedges(3)
Tools Needed
Level
This Fountain Uses
FTNCOV-LRG
FT-286E (For FT-
286)
22.25”x15”x15”
140 lb

Revised July 11, 2016
ASSEMBLY INSTRUCTIONS
1. Make sure you are assembling your fountain on a level surface capable of
holding a minimum of 500 pounds with approximately a 5 1/4” square foot
footprint.
2. Place the base (FT-286E) or (FT-288E) into position where the fountain will be
installed.
3. Place the basin (FT-286C) centered on top of the base.
4. Place the pump inside the basin and thread the cord through the back of the
basin leaving roughly 12” of cord loose.
5. Place the hose clamp over the ½” non kink tubing and attach the clamp over the
copper or CPVC piping on the water feature. Tighten the clamp.
6. Place the water feature (FT-286A) with the ½” non kink tube connected to it over
the pump.
7. Attach a hose clamp to the opposite end of the non kink tubing and connect it to
the pump. Tighten the clamp
8. Place the spiller stopper (FT-286B) on top of the water feature. The spiller
stopper is to prevent splashing.
9. Place the copper spiller in the front of the water feature where the water will be
spilling out.
10.Fill basin with just enough water to reach the pump cover (approximately 15-20
gallons).
a. Note –do not allow pump to run dry as it will cause damage to the pump.
WINTER CARE AND GENERAL FOUNTAIN INSTRUCTIONS
-W I N T E R C A R E -
Fountain bowls/tops and other fountain components, which collect water, should not be left outside in the
winter since any component, which fills with water and freezes may crack. Likewise components such as
pedestals, which remain in a basin, filled with water, which then freezes, may also crack or crumble.
Ideally, therefore, a fountain should always be stored indoors or in a dry protected place such as a
covered porch away from the elements. However, if a fountain must be left outside:
(1) Remove pump, rubber stoppers, drainpipes, finials, and other small components for storage
indoors. Note that stoppers or drainpipes are removed to allow drainage in the event water accumulates
in any basin. Compression stoppers may be left on the pump cord for easier assembly next season.
(2) Raise fountain base from ground with wood strips so that base will not freeze to the ground
surface.
(3) Cover your Campania Fountain with a Campania Fountain Cover, or wrap the fountain with
burlap or other absorbent material (old blanket or towel) and then cover securely with plastic, making sure
that water will not accumulate in the basin or other fountain component and freeze;
(4) Check fountain periodically to insure that plastic is secure and water is not accumulating in any
fountain component. -G E N E R A L F O U N T A I N T I P S -
Install fountains on a level surface. You will need a properly grounded 110-volt (AC only) GFCI protected
receptacle near the fountain for your pump. All pumps are submersible and must be completely
underwater to function properly. Test all pumps and adjust to full output prior to assembly. It is not
FT-295 & 286 Falling Water 1 & 2
Fountain
(5 pieces)
All of our cast stone is proudly

recommended that fountains be placed directly on grass or dirt. Position the channel opening at the base
of each fountain toward the electrical outlet to be used since the pump cord will be threaded through this
opening.
For more Campania product information visit www.campaniainternational.com