Campania International Rain Barrel 8265-4101 User manual

Revised October 17th, 2018
COMPONENTS AND PARTS LIST
Pump Kit Parts List
PK300 pump (1)
6” length of 1/2”Black Non-kink tubing (1) *
18” length of 1/2" Black Non-kink tubing (1)*
2” length of 5/8” clear tubing (3)*
Valve (1)*
Wedges (4)
Hose clamps (1)
* Tubing has been preassembled
8265-4101 Rain Barrel Fountain
(2 pieces)
NOTE: Component drawings are not to scale
Tools you will need
Level
Water Feature
14”W x 1”H
10 lbs
Basin
20”W x 21.5”H
60 lbs
This fountain takes cover
FTNCOV-SM
Fountain holds
approximately 10-15
gallons of water
This fountain is compatible with a
#10 or #7 Refill Device

Revised October 17th, 2018
ASSEMBLY INSTRUCTIONS
1. Make sure you are assembling your fountain on a level surface
2. Assemble the pump kit
a. NOTE: Be sure to use the appropriate size adapter provided with the pump.
b. Using a hose clamp, secure the 6” length of the 1/2" black tubing of the tubing
assembly to the pump.
3. Remove the cap covering the standpipe.
4. Feed the pump cord through the standpipe in the basin, leaving enough cord length inside
of the basin to work with the pump sitting flat in the bottom of the bowl.
5. Replace the cap to cover the standpipe and cord.
6. Slide the 3” length of 5/8” clear tubing of the tubing assembly onto the copper pipe
extending down from the bottom of the water feature
7. Place the water feature on top of the basin making sure that the water feature is level.
a. Note –Wedges may be used if necessary to level the water feature.
b. Note –Do not allow pump to run dry, as it will cause damage to the pump
WINTER CARE AND GENERAL FOUNTAIN INSTRUCTIONS
-W I N T E R C A R E -
Fountain bowls/tops and other fountain components, which collect water, should not be left outside in the winter since
any component, which fills with water and freezes may crack. Likewise components such as pedestals, which remain
in a basin, filled with water, which then freezes, may also crack or crumble. Ideally, therefore, a fountain should always
be stored indoors or in a dry protected place such as a covered porch away from the elements. However, if a fountain
must be left outside:
(1) Remove pump, rubber stoppers, drainpipes, finials, and other small components for storage indoors. Note
that stoppers or drainpipes are removed to allow drainage in the event water accumulates in any basin.
(2) Raise fountain base from ground with wood strips so that base will not freeze to the ground surface.
(3) Cover or wrap the fountain with burlap or other absorbent material (old blanket or towel) and then cover
securely with a breathable, lightly colored material (fountain covers sold by Campania International are
recommended), making sure that water will not accumulate in the basin or other fountain component and
freeze.
(4) Check fountain periodically to insure that plastic is secure and water is not accumulating in any fountain
component.
-G E N E R A L F O U N T A I N T I P S -
Install fountains on a level surface. You will need a properly grounded 110-volt (AC only) GFCI protected
receptacle near the fountain for your pump. All pumps are submersible and must be completely underwater to function
properly. Test all pumps and adjust to full output prior to assembly. It is not recommended that fountains be placed
directly on grass or dirt. Position the channel opening at the base of each fountain toward the electrical outlet to be
used since the pump cord will be threaded through this opening.
For more Campania product information visit www.campaniainternational.com
8265-4101 Rain Barrel Fountain
(2 pieces)