Campania International Wychwood FT-292 User manual

FT
-
292 Wychwood Fountain
R
evised
May22, 2019
PRODUCTINFORMATION
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecure, andwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
https://www.youtube.com/watch?v=_5mAnjH_IYY
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
Pump KitPartsList
PK120-LVpump with transformer(1)
#7 stopper(1)
2”length ofPermaGumPutty(1)
Approx.6”length of1/2”BlackNon-kinktubing (1)
Hose clamps(2)**
*Hoseclamps maybe used asflow restrictors
FOUNTAININFORMATION:
Thisfountain holdsapproximately1/2gallonof water.
Noavailable fountain coversare recommendedforthis
fountain.
Norefill device orsubmersible lightsare suggested for
thisfountain
TOOLSREQUIRED:
Bubble Level
FlatHeadScrewdriver
Scissors
PUMPINFORMATION:
WP450LV–120GPH LowVoltagePump
16 FTcord length

FT
-
292 Wychwood Fountain
R
evised
May22, 2019
ASSEMBLYINSTRUCTIONS
Assembleyourfountain onalevelsurface capableofholdingaminimumof45 pounds withan
approximate1square footfootprint.
FT-292C(21lbs)
16.25”Wx6.5”H
FT-292B(2lbs)
5.75”Wx3”H
FT-292A(7lbs)
10”Lx9.5”Wx6”H
1. Place theadhesivedots provided evenlyaround thebottomofthebasin
(FT-292C)to preventscratchinganythingbeneath thefountain.
2. Position thebasin (FT-292C)where thefountain is to beinstalled,
ensuringthatit will belevel.
3. Assemblethepump kit.
a. NOTE:Besure to usetheappropriate size
adapter providedwiththepumpand do notplug
thepumpinto thetransformeruntil assembly is
complete.
b. Usingahoseclamp and screwdriver, attach the1/2”
end ofthenon-kink tubingto thepump outlet.
c. Place oneend ofthePermaGumputtyonto thepump
cord approximatelyabout6”-8”fromthepump.
d. Wrap theputtyaround thecord once. See image “A”
e. Place thestopper around theputty. Keep thetop edge
oftheputtyand stopper flush. See image “B”
f. Cutoff theexcess puttyso thatit is even with the
outer edgeoftheslit.
4. Feed thepump cord all thewaythrough theholeand thechannelin the
basin (FT-292C)toensurethefountain will belevel.
5. Firmlypress thestopper into theholewhilepullingthecord the
remainder oftheway.
a. Usethehandleofthescrewdriver to press the
stopper down as far as possible. See image “C”
6. Fill thebasin enough to cover thepump completelywith
water to check forleaking.
a. Ifleakingoccurs…
i. Removethestopper and repeatstep 5 again.
ii. Usesomeoftheexcess puttyto sealthecord around the
top ofthestopper. See image “D”
iii. Letthefountain drycompletely, then
use100%clear siliconeto sealaround
thepump cord and perimeter ofthe
stopper.
1. Siliconemustsetfor24 hours
before addingwater
7. Place thepump house(FT-292B)over thepump and centered insideof
thelargebowl(FT-292C).
8. Usingahoseclamp and screwdriver, secure theother end ofthe1/2”
non-kink tubingto thecopper pipeprotrudingfromthebottomofthe
small bowl(FT-292A).
9. Center and lowerthesmall bowl(FT-292A) onto thepump house(FT-
292B)
10. Connectthepump cord to thetransformer.
A
B
C
D