Campbell Hausfeld IronForce IFN35650 User manual

Description
This nailer is designed for decorative
trim, molding, window casings,
furniture trim and picture frame
assembly.
Features include: convenient
rear loading magazine which holds up to
100 nails, no-mar tip, adjustable exhaust,
single cycle trigger, quick clear nose, and
an adjustable depth of drive mechanism.
General Safety
Information
CALIFORNIA PROPOSITION 65
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete, cement, or
other masonry. This dust often
contains chemicals known to cause
cancer, birth defects, or other
reproductive harm. Wear protective
gear.
Excessive exposure to vibration,
working in awkward positions and
repetitive work motions can cause
injury to hands and arms. Stop using
any tool if discomfort, numbness,
tingling or pain occur and consult a
physician.
This manual contains safety,
operational and maintenance
information.
Read this manual and
understand all safety
warnings and instructions
before operating the
nailer. Contact your
Campbell Hausfeld
representative if you have any
questions.
OPERATOR’S RESPONSIBILITY:
Before operating the nailer, read and
understand all safety warnings and
labels. Follow the operating
instructions outlined in this manual.
EMPLOYER’S RESPONSIBILITY:
Distribute this instruction manual to all
users before allowing use of the nailer.
Ensure all operators read, understand
and follow all safety warnings, labels
and instructions outlined in this
manual.
Danger indicates
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
• Do not use any type
of flammable gases
or oxygen as a power
source for the nailer.
Use filtered,
lubricated, regulated
compressed air only.
Use of a compressed gas instead of
compressed air may cause the nailer
to explode which will cause death or
serious personal injury.
• Do not exceed
maximum operating
pressure of the nailer
(120 psi). The nailer
will not function
properly. Do not use
a compressed air
source capable of more than 200 PSI.
!
DANGER
The nailer could explode which will
cause death or serious personal
injury.
• Never use gasoline
or other flammable
liquids to clean the
nailer. Never use the
nailer in the presence
of flammable liquids
or gases. Vapors could ignite by a
spark and cause an explosion which
will result in death or serious
personal injury.
• Always remain in
a firmly balanced
position when
using or handling
the nailer.
• Do not modify or
disable the Work
Contact Element
(WCE). Do not tie
or tape the WCE
or trigger in a
depressed
position. Death or serious personal
injury could result.
Model IFN35650
IN725300AV 2/08
Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National
Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008 Campbell Hausfeld/Scott Fetzer
Table Of Contents
General Safety . . . . . . . . . . . . . . . 1-3
Specifications . . . . . . . . . . . . . . . . . . 2
Operational Modes . . . . . . . . . . . . . 4
Operating The Nailer . . . . . . . . . 3-5
Troubleshooting . . . . . . . . . . . . . . . 6
Warranty . . . . . . . . . . . . . . . . . . . . . 7
MANUAL
OCO
2
Locate model and date code on
tool and record below:
Model No. ______________________
Date Code ______________________
Retain these numbers for
future reference.
Angle Finish Nailer
Operating Instructions Model IFN35650
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death
and/or property damage! Retain instructions for future reference.
See Warranty on page 7 for important information about commercial use of this product.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
For parts, product & service information
visit www.chpower.com

2
General Safety
Information (Continued)
• Do not touch the
trigger unless
driving nails.
Never attach air
line to nailer or
carry nailer
while touching
the trigger. The
tool could eject a fastener which
will result in death or serious
personal injury.
Warning indicates
a potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
• Always
disconnect
nailer from air
line before
clearing jams,
adjusting or
servicing the
nailer, relocating the nailer, or when
the nailer is not in use. Always
reconnect the air line BEFORE
loading any fasteners. The nailer
could eject a fastener causing death
or serious personal injury.
• Protect your eyes and
ears. Wear Z87 safety
glasses, with side
shields. Wear hearing
protection. Employers
and users are
responsible for ensuring the user or
anyone near the nailer wears this
safety protection. Serious eye injury
or permanent hearing loss could
result.
!
WARNING
• Do not use a
check valve or
any other
fitting which
allows air to
remain in the
nailer. Death
or serious personal injury could
occur.
• Never place
hands or any
other body parts
in the nail
discharge area
of the nailer. The
nailer might eject
a fastener and could result in death
or serious personal injury.
• Never carry the
nailer by the air
hose or pull the
hose to move
the nailer or a
compressor. Keep
hoses away from
heat, oil and
sharp edges. Replace any hose that
is damaged, weak or worn. Personal
injury or tool damage could occur.
• Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
• Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious
puncture wound.
• Do not operate
or allow
anyone else to
operate the
nailer if any
warnings or
warning labels
are not legible. Warnings or
warning labels are located on the
nailer magazine and body.
• Never leave the nailer unattended
or connected to an air compressor
when not in use. Serious personal
injury can occur if someone picks up
and uses the nailer without
knowing the correct way to operate
the nailer.
• Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
• Do not modify or alter the nailer or
any nailer parts. Do not use the
nailer if any shields or guards are
removed or altered. Do not use the
nailer as a hammer. Personal injury
or tool
damage may occur.
• Avoid long extended periods of work
with the nailer. Stop using the nailer
if you feel pain in hands or arms.
!
CAUTION
Model IFN35650
Operating Instructions
!WARNING
Quick Clear Latch
Rubber No-Mar Tip
Nail Discharge Area
Nail Loading Area
Aluminum Magazine
Hard Anodized
Trigger
Warning Decal
Trilingual
Specification
Decal
Adjustable Direction
Exhaust Deflector
• REQUIRES: 1.8 SCFM with 10 nails
per minute @ 90 psi
• AIR INLET: 1/4 inch NPT
• NAIL SIZE RANGE: 1-1/2 inch to 2-
1/2 inch
• MAGAZINE CAPACITY:
100 Nails per load, 15 gauge
• WEIGHT: 5 lbs., 11 oz.
• LENGTH: 13-3/4 inch
• HEIGHT: 12-1/4 inch
• MAXIMUM PRESSURE: 120 psi
• PRESSURE RANGE: 70 - 120 psi
Nailer Components And Specifications
Nail Pusher Assembly
Adjustable
Depth
Control
www.chpower.com

RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the nailer.
1. The air
compressor
must be able
to maintain a
minimum of
70 PSI when
the nailer is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
2. An oiler can be
used to provide oil
circulation through
the nailer. A filter
can be used to
remove liquid and
solid impurities which can rust or
“gum up” internal parts of the
nailer.
3. Use 3/8 inch
air hoses with
a minimum
working
pressure of
150 psi. Use 1/2 inch air hoses for
50 foot run or longer. For better
performance, install a 3/8 inch quick
plug (1/4 inch NPT threads) with an
inside diameter of .315 inch (8mm)
on the nailer and a 3/8 inch quick
coupler on the air hose.
4. Use a pressure regulator on the
compressor, with an operating
pressure of 0 - 125 PSI. A pressure
regulator is required to control the
operating pressure of the nailer
between 70 and 120 PSI.
3
General Safety
Information (Continued)
• Always check
that the Work
Contact
Element (WCE)
is operating
properly. A nail
could
accidentally be
driven if the
WCE is not
working properly. Personal injury
may occur (See "Checking the Work
Contact Element" Section).
• Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice indicates
important
information, that if not followed, MAY
cause damage to equipment.
• Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
• Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
• Air compressors providing air to the
nailer should follow the
requirements established by the
American National Standards
Institute Standard B19.3-1991;
Safety Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
NOTICE
Operating The Nailer
Read this manual and understand
all safety warnings and
instructions before operating the
nailer.
LUBRICATION
This nailer requires lubrication before
using the nailer for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
The work surface
can become
damaged by excessive lubrication.
Proper lubrication is the owner’s
responsibil- ity. Failure to lubricate the
nailer properly will dramatically
shorten the life of the nailer and void
your warranty.
1. Disconnect the
air supply from
the nailer to
add lubricant.
2. Turn the nailer
so the air inlet
is facing up.
Place 4-5 drops
of 30 W non-
detergent oil
into air inlet. Do not use detergent
oils, oil additives, or air tool oils. Air
tool oils contain solvents which will
damage the nailer’s internal
components.
3. After adding oil,
run nailer briefly.
Wipe off any
excess oil from
the cap exhaust.
NOTICE
Model IFN35650
Operating Instructions
70 PSI
Min.
OIL
120 PSI
Max.
150 PSI WP
3/8 inch I.D.
Recommended Hookup
Quick
Plug
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Oiler
Regulator
Filter
www.chpower.com

4. Reconnect air
supply to the
nailer.
5. Depress the
Work Contact
Element (WCE)
against the
work surface
without pulling
the trigger. The nailer MUST NOT
OPERATE. Do not use the tool if it
operates without pulling the
trigger. Personal injury may result.
6. Remove the
nailer from the
work surface.
The Work
Contact
Element (WCE)
must return to
its original down position. The
nailer MUST NOT OPERATE. Do not
use the tool if it operates while
lifted from the work surface.
Personal injury may result.
7. Pull the
trigger and
depress the
work
contact
element
(WCE) against the work surface. The
nailer MUST NOT OPERATE.
8. Depress
the Work
Contact
Element
(WCE)
against the
work surface. Pull the trigger. The
nailer MUST OPERATE.
LOADING THE NAILER
1. Always connect the tool to the air
supply before loading fasteners.
2. Insert one stick
of nails into
rear loading
slot while
holding tool
down so nails
will slide
forward in
magazine.
NOTE: Make
certain to insert
nail heads into
wide area at top of magazines with
nail points down.
Operating The Nailer
(Continued)
Operational Modes
Always know the
operational mode
of the nailer before using. Failure to
know the operational mode could
result in death or serious personal
injury.
THIS TOOL IS SOLD WITH A BLACK
SINGLE CYCLE TRIGGER. THIS TOOL
IS NOT INTENDED TO BE USED WITH
A RED BUMP CYCLE TRIGGER.
SINGLE CYCLE MODE
This method is
recommended
for precise nail
placement. This
mode requires
the trigger to
be pulled each time a nail is driven. The
nailer can be actuated by depressing
the WCE against the work surface
followed by pulling the trigger. Or the
nailer can be actuated by pulling the
trigger and then depressing the WCE
against the work surface.
The trigger must be released to reset
the tool before another nail can be
driven.
WORK CONTACT ELEMENT (WCE)
Check the opera-
tion of the Work
Contact Element (WCE) trip mechanism
before each use. The WCE must move
freely without binding through its
entire travel distance. The WCE spring
must return the WCE to its fully
extended position after being
depressed. Do not operate the nailer if
the WCE trip mechanism is not
operating properly. Personal injury may
occur.
1. Disconnect the
air supply from
the nailer.
2. Remove all
nails from the
magazine (see
Loading/
Unloading).
3.
Make sure the
trigger and
work contact
element (WCE)
move freely up
and down
without sticking or binding.
!
CAUTION
!
WARNING
3. Press “Nail
Bypass Button”
in round hole in
the Nail Pusher
Mechanism and
pull back. This
allows the nail
clip to slide fully into the magazine.
4. Release the pusher. Allow pusher to
rest against nails. The nailer is now
loaded.
UNLOADING THE NAILER
1. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of
loading, except always disconnect
the air hose before unloading.
2. Pull nail pusher
mechanism back
and press “Nail
Bypass Button.”
3. Hold tool
upright so nails
will slide out of
magazine.
4. Release the
Pusher.
ADJUSTING THE NAIL PENETRATION
The IFN35650 is equipped with an
adjustable depth of drive feature. This
allows the user to determine how deep a
fastener will be driven into the work
surface.
1. Adjust the
operating
pressure to
a pressure
which will
consistently
drive the
fasteners. Do not exceed the
maximum operating pressure of the
nailer of 110 psi.
2
1
12
2
1
4
Model IFN35650
Operating Instructions
www.chpower.com
Nail Pusher
Mechanism
Slot
Nail Bypass Button
Pusher
Mechanism
Nail
Nail Bypass Button
COUNTER-
CLOCKWISE CLOCKWISE
Movement

4. The door can
now be
rotated,
exposing the
jammed
fastener.
5. Remove the
jammed
fastener,
using pliers or
a screwdriver
if required.
6 Rotate door
back into the
closed
position.
7. Extend the
wire latch and
place over the
hooks on the
nose.
8. Close the latch
by pushing the
latch up and in
until the latch
snaps into
place.
9.
Make sure the
trigger and
work contact
element (WCE)
move freely up
and down
without sticking or binding.
Operating The Nailer
(Continued)
2. To increase
depth of drive,
first pull up on
the upper
WCE, then
rotate
thumbwheel
to the left
(counter-
clockwise). To decrease depth of drive,
rotate thumbwheel to the right
(clockwise). Then release upper WCE
into detents which hold the
thumbwheel in place after each
adjustment.
3. Make sure that the
trigger and work
contact element
(WCE) move freely up
and down without
binding or sticking
after each adjustment.
ADJUSTING THE DIRECTION OF THE
EXHAUST
The IFN35650 is
equipped with an
adjustable
direction exhaust
deflector. This is
intended to allow
the user to change the direction of the
exhaust. Simply twist the deflector to
any direction desired.
CLEARING A JAM FROM THE NAILER
1. Disconnect the
air supply from
the nailer.
2. Remove all nails
from the
magazine (see
Loading/
Unloading).
Failure to do so
may cause the nails to eject from
the front of the nailer.
3. Undo latch by
pulling out and
down. The wire
latch will
disengage from
the hooks on the
nose.
Technical Support
Please call our Nailer Hotline at
1-800-543-6400 with any questions
regarding the operation or repair of
this nailer.
Fastener And Replacement
Parts
Use only 15 gauge
35° fasteners. Use only genuine
Campbell Hausfeld replacement parts.
Never substitute parts. Do not use
modified parts or parts which will not
give equivalent performance to the
original equipment. Tool performance,
safety and durability could be reduced.
When ordering replacement parts or
fasteners, specify by part number.
Nailer Repair
Nailer repairs must be performed by
qualified and experienced service
people ONLY.
Assembly Procedure For
Seals
When repairing a nailer, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. After
reassembling, a few drops of 30W non-
detergent oil or equivalent, must be
added through the air line before
testing.
!
WARNING
Movement
Fasteners Information
Nails used in the Campbell Hausfeld IFN35650 Angle Finish Nailer will also work in Sears 18329, Porter Cable DA250, Senco
SFN2B, SFN1 and SFN40.
Movement
Rotate
5
Model IFN35650
Operating Instructions
www.chpower.com

Air leaking at trigger
valve
Air leaking between
housing and nose
Air leaking between
housing and cap
Nailer skips driving
nail
Nailer runs slow or
has loss of power
Nails are jammed in
nailer
O-Rings in trigger valve housing are
damaged
Loose screws in housing
Damaged O-Rings
Damage to bumper
Loose screws
Damaged gasket
Worn bumper
Dirt in nose piece
Dirt or damage prevent nails or
pusher from moving freely in
magazine
Damaged pusher spring
Inadequate air flow to nailer
Worn O-Ring on piston or lack of
lubrication
Damaged O-Ring on trigger valve
Air leaks
Cap gasket leaking
Nailer not lubricated sufficiently
Broken spring in cylinder cap
Exhaust port in cap is blocked
Guide on driver is worn
Nails are not correct size
Nails are bent
Magazine or nose screws are loose
Driver is damaged
Replace O-Rings. Check operation of Work Contact
Element (WCE)
Tighten screws
Replace O-Rings
Replace bumper
Tighten screws
Replace gasket
Replace bumper
Clean drive channel
Clean magazine
Replace spring
Check fitting, hose or compressor
Replace and lubricate O-Rings
Replace O-Rings
Tighten screws and fittings
Replace gasket
Lubricate nailer
Replace spring
Replace damaged internal parts
Replace guide
Use only recommended nails
Replace with undamaged nails
Tighten screws
Replace driver
Troubleshooting Guide
Stop using nailer immediately if any of the following problems occur. Serious personal injury could result.
Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.
!
WARNING
Problem Cause Solution
6
Model IFN35650
Operating Instructions
www.chpower.com

Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,
Harrison, Ohio, 45030, Telephone: [phone]
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the
Campbell Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun,
inflator or air accessory supplied or manufactured by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the
duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial,
industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States
do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance
with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or
failure to operate products in accordance with instructions shall also include the removal or alteration of any safety
devices. If such safety devices are removed or altered, this warranty is void.
D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.
E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields,
driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants,
material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters,
collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other
expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original
purchase. Underlined items are warranted for defects in material and workmanship only.
F. Cosmetic defects that do not interfere with the product’s function.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or
components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Call Campbell Hausfeld (800-543-6400) to obtain your warranty service options. Freight costs must be borne by the
purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be
scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability
of replacement parts.
This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may
also have other rights which vary from state to state or country to country.
7
Model IFN35650
Operating Instructions
www.chpower.com

Notes
8
Model IFN35650
Operating Instructions
www.chpower.com

Cesser d’utiliser tout outil s’il y a
malaise, engourdissement,
fourmillement ou douleur et consulter
un médecin.
Ce manuel contient des informations
concernant la sécurité, le
fonctionnement et l’entretien.
Lire attentivement ce
manuel et comprendre tous
les avertissements de
sécurité et les instructions
avant d’utiliser la cloueuse.
Si vous avez des questions,
contacter un représentant de
Campbell Hausfeld.
RESPONSABILITÉ DE L’UTILISATEUR
Avant d’utiliser cette cloueuse, prendre
connaissance de tous les avertissements
et des étiquettes concernant la
sécurité. Suivre les instructions données
dans ce manuel.
RESPONSABILITÉ DE L’EMPLOYEUR
Ce manuel d’instruction doit être mis à
la disposition de tous les utilisateurs
avant qu’ils ne se servent de la
cloueuse. S’assurer que tous les
utilisateurs lisent et comprennent
parfaitement les notices de sécurité,
étiquettes et instructions décrites dans
ce manuel.
Danger
Danger indique une situation
hasardeuse imminente qui RÉSULTERA
en perte de vie ou blessures graves.
• Ne pas utiliser un gaz
inflammable ni
l’oxygène pour
alimenter la cloueuse.
Utilisez seulement de
l’air comprimé filtré,
lubrifié et réglé.
L’utilisation d’un gaz comprimé au
lieu de l’air comprimé peut faire
exploser la cloueuse et entraîner
des blessures graves ou mortelles.
!
DANGER
Description
Cette cloueuse est conçue pour
boiseries, moulures intérieures,
plinthes, panneaux et armoires.
Caractéristiques: chargement facile du
magasin par l’arrière, capacité de 100
clous, embout ne laissant pas de
marque, éjection réglable, gâchette à
un coup, buse à dégagement rapide,
réglage de pénétration des clous.
Généralités Sur La
Sécurité
PROPOSITION 65 CALIFORNIE
Vous pouvez créer de la
poussière en coupant,
ponçant, perçant ou meulant
les matériaux tels que le bois, la
peinture, le métal, le béton, le ciment
ou autre maçonnerie. Cette poussière
contient souvent des produits
chimiques reconnus pour causer le
cancer, les déformations congénitales
ou autres problèmes de la
reproduction. Portez de l’équipement
de protection.
Toute
exposition excessive aux vibrations, tout
travail dans des positions incommodes et
tous déplacements à répétition peuvent
causer des blessures aux mains et aux
bras.
• Ne pas dépasser la
pression de service
maximale de la
cloueuse (827 kPa).
La cloueuse ne
fonctionnera pas
correctement. Ne pas
utiliser une source d’air comprimé
qui a une capacité de plus que 1379
kPa. La cloueuse pourrait exploser et
causer des blessures graves ou
mortelles.
• Ne jamais utiliser de
l’essence ni les fluides
inflammables pour le
nettoyage de la
cloueuse. Ne
jamais utiliser la
cloueuse près d’un liquide ou gaz
inflammable. Une étincelle peut
allumer les vapeurs et causer une
explosion qui peut résulter en perte
de vie ou blessures graves
personnelles.
MANUAL
OCO
2
827 kPa
Max.
Modèle IFN35650
IN725300AV 2/08
Les Cloueuses Campbell Hausfeld conforment aux/ou dépassent les standards de l’American National
Standard/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008 Campbell Hausfeld/Scott Fetzer
Table Des Matières
Directives De Sécurité . . . . . . . . 9 -11
Spécifications . . . . . . . . . . . . . . . . . 10
Modes De Fonctionnement . . . . . 12
Fonctionnement De
La Cloueuse . . . . . . . . . . . . . . . 11-13
Guide De Dépannage . . . . . . . . . . 14
Garantie . . . . . . . . . . . . . . . . . . . . . 15
Trouver le numéro de modèle et le
code date sur le chargeur de l’outil
et inscrire plus bas:
Nº du Modèle ___________________
Code de date ____________________
Conserver ces numéros
comme référence.
Cloueuse À Angle
Pour Finition
Instructions D’Utilisation Modèle IFN35650
S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit
décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!
Conserver ces instructions comme référence.
Voir la Garantie à la page 15 pour de l’information importante sur l’utilisation commercial de ce produit.
MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!
Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.
9Fr

Généralités Sur La
Sécurité (Suite)
• Toujours bien
s’équilibrer
pendant la
manipulation ou
l’utilisation de la
cloueuse.
• Ne jamais modifier
ou empêcher le
fonctionnement
du mécanisme de
déclenchement par
contact (WCE) et ne
jamais maintenir la
gâchette enfoncée à l’aide de ruban
adhésif par exemple. Ceci pourrait
entraîner des blessures graves ou
mortelles.
• Ne toucher à la
gâchette qu’au
moment de poser
des clous. Ne jamais
actionner la gâchette
durant le transport
de la cloueuse ou
durant le raccordement de celle-ci au
tuyau d’air comprimé. L’éjection
accidentelle d’un clou peut causer
des blessures graves ou mortelles.
Avertissment indique une situation
hasardeuse potentielle qui PEUT résulter
en perte de vie ou blessures graves.
• Toujours débrancher le
tuyau d’air comprimé
de la cloueuse avant
de dégager un clou
bloqué, de régler, de
réparer ou de transporter la cloueuse
ou lorsque celle-ci n’est pas en service.
!
AVERTISSEMENT
Le raccordement du tuyau d’air
comprimé doit toujours s’effectuer
AVANT le chargement du magasin.
L’éjection accidentelle d’un clou peut
causer des blessures graves ou mortelles.
• Protéger vos yeux avec
des lunettes de sécurité
Z87 à écrans latéraux et
vos oreilles avec un
protecteur auditif. Le
patron et l’utilisateur sont
responsables pour assurer que
l’utilisateur et ceux à proximité de la
cloueuse portent l’équipement de
securite, sinon, il y a risque de
blessures graves oculaires ou de
dommage permanent a l’ouie. sécurité,
sinon, il y a risque de blessures graves
oculaires l’équipement de sécurité,
sinon, il y a risque de blessures graves
oculaires ou de dommage permanent à
l’ouie. sécurité, sinon, il y a risque de
blessures graves oculaires ou de
dommage permanent à l’ouïe.
• Ne pas utiliser
un clapet ni
autre raccord
qui permet que
l’air reste dans
la cloueuse.
Cela peut
entraîner des blessures graves ou
mortelles.
• Ne jamais poser
l’embout de
clouage sur la
main ou sur toute
autre partie du
corps. L’éjection
accidentelle d’un
clou peut causer des blessures
graves ou mortelles.
• Ne jamais
transporter la
cloueuse par le
tuyau à air. Ne
jamais tirer sur le
tuyau pour
déplacer la
cloueuse ou le compresseur.
Garder le tuyau à air à l’écart de la
chaleur, l’huile et les objets pointus.
Remplacer les tuyaux endommagés,
faibles ou usés. Sinon, il y a risque
de blessures personnelles ou de
dommage à l’outil.
• Toujours présumer que la cloueuse
contient des clous. Ne jamais traiter
la cloueuse de jouet. Toujours tenir
les autres personnes à l’écart de
l’endroit de travaille en cas
d’expulsion accidentelle. Ne jamais
diriger la cloueuse vers une autre
personne. Le déclenchement
accidentel de la cloueuse peut causer
la mort ou blessures graves.
• Ne jamais enfoncer
les clous un par
dessus l’autre. Le
clou pourrait
ricocher et causer
la mort ou une
blessure grave de perforation.
• Ne pas utiliser
la cloueuse/ni
permettre
qu’une autre
personne
l’utilise si les
avertissements
ou les étiquettes d’avertissement
situés sur le chargeur et corps de
la cloueuse ne sont pas lisables.
Loquet de
dégagement
rapide
Buse en
caoutchouc
non-gâchable Endroit d’expulsion des clous
Gâchette
Endroit de
chargement
de clous
Déflecteur d’échappement
orientable
• EXIGE: 0,05 m3/min avec 10 clous
par minute à 621 kPa
• PRISE D’AIR: 1/4 po NPT
• TAILLES DE CLOUS:
1-1/2 po à 2-1/2 po
• CAPACITÉ DU CHARGEUR:
100 Clous par charge, calibre 15
• POIDS: 2,27 kg, 311,9 g
• LONGUEUR: 13-3/4 po
• HAUTEUR: 12-1/4 po
• PRESSION MAXIMALE: 827 kPa
• GAMME DE PRESSION:
483 - 827 kPa
Pièces Détachées et Spécifications
de la Cloueuse
Chargeur d’aluminium
anodisé et durci
Décalque
d’avertissement
trilingue
Décalque de
spécifications
Montage de
poussoir de clous
Contrôle de
profondeur réglable
10 Fr
Modèle IFN35650
Instructions D’Utilisation
!AVERTISSEMENT