Camtree RAYO Mini User manual

RAYO Mini 8ft track dolly slider
I N S T R U C T I O N M A N U A L
F o r d e m o n s t r a t i o n o n l y
All rights reserved
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted
by the applicable copyright statutes or in writing by the Publisher.

Camtree RAYO Mini 8 track dolly slider 2
Introducon 3
In the box 3
Assembling of track & Installing Central Support Aachment 4
Carriage Assembly 5
Installing end feet and aaching to the tripods 6
Aaching the central support 7
Aaching the camera onto the dolly 7
Aaching the bowl base 7
Aaching the at base 9
Mounng the motor 9
Aaching wire with motor 11
Warranty 12
Secon Page
TA B L E O F C O N T E N T S

Camtree RAYO Mini 8 track dolly slider 3
INTRODUCTION
Introducing Camtree Hunt Shoulder Support Rig kit, designed while keeping your Sony PXW-FS5 Camera in
mind to bring out tremendous eects in your shots. It’s constructed from high quality aluminum to meet the
rigors of producon. The quality constructed top plates feature accessory mounng threads, robust base
plate allows quick camera mounng, Ergonomic Shoulder pad enables enduring comfort for long shoong
hours, and sturdy handle set adjusts as per shoong requirements. Not just that this package includes a ro-
bust mae box for cinemac eects and high grade follow focus for accurate focus pulls.
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is pictured
and listed below.
Note: 1. If you have purchased Rayo Mini (C-RAYO-MINI), you will receive only 1 box that contains the dolly &
its parts.
Note: 2. If you have purchased Rayo Mini Motorised (C-RAYO-MINI-E), you will receive 2 boxes that
contains the dolly & electronic parts.
P a c k a g i n g M a t e r i a l o f B o x 1
End Adapter
End Foots
Wheel assembly brackets (boom)
4 Track rail
100 mm& 75mm
Bowl Base
Top Plate
Central support aachment
Thumb screws
Wheel assembly brackets
Flat base Central Joiner
Leg Assembly Knobs

Camtree RAYO Mini 8 track dolly slider 4
 Aach the track secons & align the threaded hole of track rod. Now aach central joiner with the track
secons and ghten both the knobs. Repeat the same on other side to complete the track.
A S S E M B L I N G O F T R A C K & I N S T A L L I N G C E N T R A L S U P P O R T A T T A C H M E N T
1
1
P a c k a g i n g M a t e r i a l o f B o x : 2
AC Adapter
Knobs Allen keys
Adapters
Remote Connecng Cable
Remote controller
Motor aachment
Note: The central support aachment is used at track joints to support the center of the track on a tripod or
other surface.
Note: You will receive these following parts only in case if you have purchased Rayo Mini motorized slider
(C-RAYO-MINI-E).
Hing clamps

Camtree RAYO Mini 8 track dolly slider 5
 Insert the four thumb screws loosely into top plate. Slide the two wheel assembly brackets (top) into
place and ghten the four thumb screws completely.
CARRIAGE ASSEMBLING
 Aach the wheel assembly brackets (boom) with the wheel assembly brackets (top) and ghten the
thumb screws top and boom.
 Now install your dolly onto the track as
shown.

Camtree RAYO Mini 8 track dolly slider 6
INSTALLING THE END FEET AND ATTACHING TO THE TRIPODS
 Now open the end foots to aach with track secons.
 Now aach the end adapters to both ends of the track and secure it with the help of provided knobs.
 Loosen this knob to detach the dolly foots for aaching it to tripod stand.
Note: Both ends having a 1/4”-16 threads

Camtree RAYO Mini 8 track dolly slider 7
 Now aach the central support aachment with foot and secure it with the help of provided knob.
ATTACHING THE CENTRAL SUPPORT
 Now aach the foot with central joiner and
ghten the screw.
ATTACHING THE CAMERA ONTO THE DOLLY
Note: we provide two types of camera mounng . One is bowl mount & other is at base.
Aaching the bowl base
 The bowl base has several threads in order
to aach it to top plate of dolly.

Camtree RAYO Mini 8 track dolly slider 8
 Insert the thumb screw from boom of top plate and screw in the bowl adapter .
 Now mount your 100mm uid head on the bowl and secure it properly with the help of knob.
Note: we provide a conversion ring of 75mm in
order to convert 100mm bowl to 75mm bowl.

Camtree RAYO Mini 8 track dolly slider 9
 Now aach the camera with quick release plate of your uid head and ghten it with screw driver. Then
mount it on the uid head and secure properly with the help of knob.
A t t a c h i n g t h e f l a t b a s e
 Aach the at base to the top plate of dolly.
M O U N T I N G T H E M O T O R :
 Locate the two threaded holes on the top plate. Aach the motor by inserng thumb screws into
threaded holes on the top plate. Tighten the thumb screws properly to secure the motor on dolly.
Note: If you have purchased Rayo Mini Motorized (CH-RAYO-MINI-E), follow these steps to aach the motor.

Camtree RAYO Mini 8 track dolly slider 10
Threaded Holes
 Now, Adjust the motor part as shown in the
image in order to aach the belt on to the
pulley.
 Then insert the belt through the pulley. For this, insert the belt from one side, overlap it on the pulley &
then pull out the belt from other end.