Candeo C201 User manual

Candeo Zigbee Dimmer module - C201
Max dial -
Used to set maximum
brightness
Speed dial -
To adjust the dimming
speed
Min dial -
To set the minimum
dimming level
LED indicator
Reset Button
Push / Retractive switch
• Zigbee 3.0
• Compatible with Philips Hue, Smartthings, Hubitat, Home Assistant plus others
• Compatible with Alexa and Google Assistant if your zigbee hub/bridge supports it
• Works with multi-way physical switches, when used with retractive switches
• Saves and restores the last status in event of a power failure
• Minimum and maximum brightness, and dimming speed, can all be set
• Does not require a neutral wire
• Suitable for 10-250W LED and Halogen lamps
• Module can be paired directly to a Touchlink remote without a hub or bridge.
• Supports Find and Bind mode for Zigbee remotes
• Supports resistive loads and capacitive
Features
Specications
Input Voltage 220V-240V ~ 50Hz
Power Load 5-250VA LED
5-250W Halogen
Minimum Load per lamp 5W
Dimmer Control Mode RC Phase Cut
Dimensions 45mm x 45mm x 20mm
Instructions version: 2202.1

Please read all of the instructions prior to installation
Candeo Zigbee Dimmer module - C201
Safety Warnings
• Turn O󰀨 Mains Power before installing the device
• Do not expose the device to moisture
• Do not open the case of the dimmer
Installation
1. Turn o󰀨 the power.
i. To avoid electrical shock and/or equipment damage, disconnect electrical power at the main fuse or
circuit breaker before installation and maintenance.
ii. Be aware that even if the circuit breaker is o󰀨, some voltage may remain in the wires — before
proceeding with the installation, be sure no voltage is present in the wiring.
iii. Take extra precautions to avoid accidentally turning the device on during installation.
2. Connect the device according to the diagrams shown below for either a 2-wire or 3-wire system.
i. Please note, if you are not using a N wire, connect the N (Cx) and Load ( ) terminal to improve the
stability of the dimming.
N
L
Min.
Reset
Indicator
Max.
Speed.
Cx
L L
230V～50Hz 5-250W
Trailing Edge Smart Dimmer
candeo
C201
Min.
Reset
Indicator
Max.
Speed.
Cx
L L
230V～50Hz 5-250W
Trailing Edge Smart Dimmer
candeo
C201
N
L
N
L
Min.
Reset
Indicator
Max.
Speed.
Cx
L L
230V～50Hz 5-250W
Trailing Edge Smart Dimmer
candeo
C201
Min.
Reset
Indicator
Max.
Speed.
Cx
L L
230V～50Hz 5-250W
Trailing Edge Smart Dimmer
candeo
C201
N
L
3. Turn the power back on.
Caution: If in any doubt about how to install the module, please consult a qualied
electrician.
Push / Retractive
switch

Candeo Zigbee Dimmer module - C201
Zigbee conguration
1. Factory Reset
i. Press and hold the reset button for 5 seconds
ii. The LED will go red for 10 seconds, after which the reset is complete
2. Add the module to your Zigbee hub or bridge
i. Double press the reset button
ii. The LED will start blinking blue indicating that the module is in pairing mode. Pairing
mode will time-out after 15 minutes.
iii. Please refer your smart controller app to add a device to the zigbee network.
iv. The LED will stay solid blue for 10 seconds once pairing is complete
LED indicator
Reset Button
3. To remove the module from your Zigbee network
i. Remove the device from your Zigbee network by following the instructions in your
smart app
ii. Press the reset button 3 times

Candeo Zigbee Dimmer module - C201
Zigbee conguration - advanced
4. Set up Touchlink - if you have a Touchlink capable remote
i. Press the reset button 4 times
ii. The LED will start blinking green indicating that the module is ready for Touchlink mode. Pairing
mode will time-out after 15 minutes.
iii. Bring the remote within 10cm of the module and set the remote into Touchlink commissioning mode.
You will need to refer to the instructions that came with the remote to do this.
iv. The light will blink 10 times Touchlink pairing has been successful, and the LED will stay solid green
for 10 seconds once pairing is complete
Please Note
• When both devices (Dimmer and remote) are not included in a Zigbee network, each module can connect
with up to 1 remote control.
• When both devices are included in the same Zigbee network, each dimmer can connect with up to 30
remote controls.
• For Philips Hue Hubs and Amazon Echo Plus, rst add the remote and the device to network, and then
begin Touchlink pairing.
5. Find and Bind
i. Press the reset button 5 times
ii. The LED will start blinking yellow indicating that the module is ready for Find and Bind mode. Pairing
mode will time-out after 15 minutes.
iii. Set the remote into Find and Bind mode. You will need to refer to the instructions that came with the
remote to do this.
iv. The will be an indication on the remote that Find and Bind mode has been successfully established.
Fine Tuning
To optimise the performance of the smart module, or to adjust the settings to your preference, you can adjust
the brightness at the Min. and Max. level, and adjust dimming speed.
i. MIN adjustment - Switch on the lights. When the lights are on, insert a screwdriver into the MIN dial
and turn it to the left, and lower the brightness level of the lights. When the light becomes unsteady, turn
it slightly back to the right till the light remains steady.
ii. MAX adjustment - Switch on the lights. When the lights are on, insert a screwdriver into the MAX dial
and turn it to the right, and increase the brightness of the lights. When the light becomes unsteady, turn
it slightly back to the left till the light remains steady.
iii. Dimming Speed adjustment - Insert a screwdriver into the Speed dial, turn it clockwise to increase
the dimming speed and anti-clockwise to decrease the dimming speed.
For further support please go to www.candeo.io