Canon imageRUNNER C1335 Series User manual

987654321
imageRUNNER C1335/C1325 Series
Service Manual Rev. 2.0
Product Overview
Technical Explanation
Periodical Service
Disassembly/Assembly
Adjustment
Troubleshooting
Error•Jam•Alarm
Service Mode
Installation
Appendix

Application
This manual has been issued by Canon Inc. for qualied persons to learn technical theory,
installation, maintenance, and repair of products. This manual covers all localities where the
products are sold. For this reason, there may be information in this manual that does not
apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements
or changes in products. When changes occur in applicable products or in the contents of this
manual, Canon will release technical information as the need arises. In the event of major
changes in the contents of this manual over a long or short period, Canon will issue a new
edition of this manual.
The following paragraph does not apply to any countries where such provisions are
inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks
of the individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
not be copied, reproduced or translated into another language, in whole or in part, without the
consent of Canon Inc.
Copyright CANON INC. 2015
Caution
Use of this manual should be strictly supervised to avoid disclosure of condential
information.

Explanation of Symbols
The following symbols are used throughout this Service Manual.
Symbols Explanation Symbols Explanation
Check. 1x Remove the claw.
Check visually. 1x Insert the claw.
Check a sound. Push the part.
1x Disconnect the connector. Connect the power cable.
1x Connect the connector. Disconnect the power
cable.
1x
Remove the cable/wire
from the cable guide or wire
saddle.
Turn on the power.
1x Install the cable/wire to the
cable guide or wire saddle. Turn off the power.
1x Remove the screw. 1x Loosen the screw.
1x Install the screw. 1x Tighten the screw.
Symbols Explanation Symbols Explanation
Cleaning is needed. Measurement is needed.
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specic functions and the
relationship between electrical and mechanical systems with reference to the timing of
operation.
In the diagrams, represents the path of mechanical drive; where a signal
name accompanies the symbol, the arrow indicates the direction of the
electric signal.
The expression "turn on the power" means ipping on the power switch, closing the
front door, and closing the delivery unit door, which results in supplying the machine with
power.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the eld. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product
improvement or other purposes, and major changes will be communicated in the form of
Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
in the machine.

0 Safety Precautions
Laser Safety --------------------------------------------------------------------0-2
Handling of Laser System --------------------------------------------------0-2
Turn Power Switch ON ------------------------------------------------------0-3
Power Supply ------------------------------------------------------------------0-3
Safety of Toner -----------------------------------------------------------------0-4
About Toner ------------------------------------------------------------------------- 0-4
Toner on Clothing or Skin -------------------------------------------------------- 0-4
Notes When Handling a Lithium Battery --------------------------------0-4
Notes Before Servicing ------------------------------------------------------0-4
Points to Note at Cleaning --------------------------------------------------0-4
Notes On Assembly/Disassembly -----------------------------------------0-5
Points to Note when Tightening a Screw ------------------------------------ 0-5
1 Product Overview
Product Lineup -----------------------------------------------------------------1-2
Host machine ----------------------------------------------------------------------- 1-2
Option --------------------------------------------------------------------------------- 1-3
Features -------------------------------------------------------------------------1-5
Product Features ------------------------------------------------------------------- 1-5
Specications ------------------------------------------------------------------1-6
Specications ----------------------------------------------------------------------- 1-6
Weight and Size -------------------------------------------------------------------- 1-6
Productivity (Print speed) -------------------------------------------------------- 1-7
Paper type --------------------------------------------------------------------------- 1-8
Parts Name ------------------------------------------------------------------- 1-11
External View ---------------------------------------------------------------------- 1-11
Cross Sectional View ------------------------------------------------------------1-14
Operation ---------------------------------------------------------------------------1-15
Contents
2 Technical Explanation
Basic Conguration -----------------------------------------------------------2-2
Functional Conguration --------------------------------------------------------- 2-2
Original Exposure and Feed System -------------------------------------2-3
Construction ------------------------------------------------------------------------- 2-3
Basic Operation -------------------------------------------------------------------- 2-6
Reader Unit controls -------------------------------------------------------------2-13
Image Processing -----------------------------------------------------------------2-14
Control of ADF ---------------------------------------------------------------------2-20
Service Tasks ----------------------------------------------------------------------2-26
Main Controller -------------------------------------------------------------- 2-27
Overview ----------------------------------------------------------------------------2-27
Laser Exposure System --------------------------------------------------- 2-29
Overview ----------------------------------------------------------------------------2-29
Specication ------------------------------------------------------------------------2-31
Various Controls -------------------------------------------------------------------2-32
Service Tasks ----------------------------------------------------------------------2-37
Image Formation System ------------------------------------------------- 2-38
Overview ----------------------------------------------------------------------------2-38
Controls -----------------------------------------------------------------------------2-41
Service Tasks ----------------------------------------------------------------------2-70
Fixing System ---------------------------------------------------------------- 2-71
Overview ----------------------------------------------------------------------------2-71
Controls -----------------------------------------------------------------------------2-73
Service Tasks ----------------------------------------------------------------------2-86
Pickup / Feed System ------------------------------------------------------ 2-87
Overview ----------------------------------------------------------------------------2-87
Controls -----------------------------------------------------------------------------2-90
Service Tasks -------------------------------------------------------------------- 2-102
External Auxiliary System ----------------------------------------------- 2-103
Controls --------------------------------------------------------------------------- 2-103

Embedded RDS ----------------------------------------------------------- 2-108
Product Overview --------------------------------------------------------------- 2-108
Limitations ------------------------------------------------------------------------ 2-109
Service cautions ----------------------------------------------------------------- 2-110
E-RDS Setup --------------------------------------------------------------------- 2-110
FAQ --------------------------------------------------------------------------------- 2-112
Troubleshooting ----------------------------------------------------------------- 2-113
Error code and strings --------------------------------------------------------- 2-115
3 Periodical Service
List of periodically replacement parts, consumable parts and
locations for cleaning ---------------------------------------------------------3-2
Periodically Replacement Parts ------------------------------------------------ 3-2
Estimated Life of Consumables ------------------------------------------------ 3-2
Consumable parts ----------------------------------------------------------------- 3-3
4 Disassembly/Assembly
Preface --------------------------------------------------------------------------4-2
Outline -------------------------------------------------------------------------------- 4-2
Points to Note when Tightening a Screw ------------------------------------ 4-2
List of Parts ---------------------------------------------------------------------4-3
External / Internal Cover --------------------------------------------------------- 4-3
List of Main Unit -------------------------------------------------------------------- 4-6
Electrical Components ------------------------------------------------------------ 4-9
List of Connectors ----------------------------------------------------------- 4-19
External Cover/Interior System ------------------------------------------ 4-30
Layout Drawing --------------------------------------------------------------------4-30
Removing the Front Cover -----------------------------------------------------4-33
Removing the Rear Cover 1 ---------------------------------------------------4-34
Removing the Left Upper Cover ----------------------------------------------4-36
Removing the Left Lower Cover ----------------------------------------------4-36
Removing the Right Front Cover ----------------------------------------------4-37
Removing the Right Rear Cover/Right Rear Lower Cover -------------4-38
Removing the Right Upper Cover --------------------------------------------4-39
Removing the Right Cover Unit -----------------------------------------------4-41
Removing the Multi-purpose Tray --------------------------------------------4-44
Removing the Delivery Tray ----------------------------------------------------4-45
Removing the Rear Upper Cover ---------------------------------------------4-45
Removing the Upper Cover ----------------------------------------------------4-46
Removing the Control Panel Unit ---------------------------------------------4-47
Original Exposure/Feed System ---------------------------------------- 4-50
Layout Drawing --------------------------------------------------------------------4-50
Removing the ADF Unit ---------------------------------------------------------4-51
Removing the ADF Pickup Unit -----------------------------------------------4-59
Removing the ADF Separation Pad ------------------------------------------4-60
Removing the ADF Pickup Feed Unit ----------------------------------------4-61
Removing the ADF Feed Drive Unit ------------------------------------------4-64
Opening the ADF Unit + Reader Unit ----------------------------------------4-66
Removing the ADF Unit + Reader Unit --------------------------------------4-67
Removing the Copyboard Glass Unit ----------------------------------------4-69
Removing the CIS Unit ----------------------------------------------------------4-73
Removing the Reader Motor ---------------------------------------------------4-78
Controller System ----------------------------------------------------------- 4-80
Layout Drawing --------------------------------------------------------------------4-80
Removing the Main Controller Unit -------------------------------------------4-81
Removing the DC Controller PCB --------------------------------------------4-84
Removing the DC Controller PCB Unit --------------------------------------4-86
Removing the Secondary Transfer High-voltage PCB/
Developing High-voltage PCB Unit -------------------------------------------4-88
Removing the Primary Transfer High-voltage PCB Unit ----------------4-90
Removing the Power Supply Cooling Fan ----------------------------------4-93
Removing the Low-voltage Power Supply PCB Unit---------------------4-93
Removing the Touch Panel/Control Panel CPU PCB Unit /
LCD Unit ----------------------------------------------------------------------------4-97
Removing the Fax Speaker Unit -------------------------------------------- 4-100
Removing the Fax Unit -------------------------------------------------------- 4-101
Laser Exposure System ------------------------------------------------- 4-102
Layout Drawing ------------------------------------------------------------------ 4-102
Removing the Laser Scanner Unit ------------------------------------------ 4-102
Image Formation System ----------------------------------------------- 4-106
Layout Drawing ------------------------------------------------------------------ 4-106
Removing the Waste Toner Container ------------------------------------- 4-108

Removing the Toner Container (Y/M/C/Bk) ------------------------------ 4-109
Removing the Drum Unit (Y/M/C/Bk) -------------------------------------- 4-109
Removing the ITB Unit -------------------------------------------------------- 4-112
Removing the Registration Patch Sensor Unit -------------------------- 4-117
Removing the Secondary Transfer Outer Roller Unit ------------------ 4-119
Removing the Secondary Transfer Outer Roller Guide Unit --------- 4-120
Removing the Registration Drive Unit ------------------------------------- 4-123
Removing the Main Drive Unit ----------------------------------------------- 4-125
Removing the Hopper Unit (Y/M/C/Bk) ------------------------------------ 4-127
Removing the ITB Pressure Release Switch ---------------------------- 4-130
Removing the Bottle Drive Unit (Y/M/C/Bk) ------------------------------ 4-131
Removing the Toner Bottle Mount (Y/M/C/Bk) --------------------------- 4-132
Fixing System -------------------------------------------------------------- 4-137
Layout Drawing ------------------------------------------------------------------ 4-137
Removing the Fixing Assembly ---------------------------------------------- 4-137
Removing the Fixing Film Unit / Pressure Roller Unit ----------------- 4-138
Removing the Fixing Drive Unit --------------------------------------------- 4-141
Pickup/Feed System ----------------------------------------------------- 4-143
Layout Drawing ------------------------------------------------------------------ 4-143
Removing the Right Inner Cover Unit -------------------------------------- 4-144
Removing the Cassette Pickup Roller/Cassette Separation Roller/
Cassette Feed Roller ---------------------------------------------------------- 4-145
Removing the Multi-purpose Tray Pickup Roller
/Multi-purpose Tray Separation Roller
/Multi-purpose Tray Feed Roller --------------------------------------------- 4-149
Reassembling when the Multi-purpose Tray Separation Roller
Shaft is detached --------------------------------------------------------------- 4-153
Removing the Registration/Pickup Unit ----------------------------------- 4-158
Removing the Delivery/Reverse Unit -------------------------------------- 4-166
Removing the Cassette 1 Lifter Drive Unit ------------------------------- 4-167
Removing the Cassette 1 Pickup Drive Unit ----------------------------- 4-170
Cleaning Procedure ------------------------------------------------------ 4-172
Layout Drawing ------------------------------------------------------------------ 4-172
Cleaning the Copyboard Glass/Reading Glass ------------------------- 4-173
Cleaning the Dustproof Glass ----------------------------------------------- 4-173
Cleaning when installing/removing the ITB Unit ------------------------ 4-174
Cleaning the Registration Patch Sensor Unit ---------------------------- 4-175
Cleaning the Registration Front Guide ------------------------------------ 4-176
Cleaning the Registration Roller/Pre-registration Roller -------------- 4-177
Cleaning the Secondary Transfer Guide ---------------------------------- 4-178
Cleaning the Fixing Inlet Guide ---------------------------------------------- 4-180
5 Adjustment
Document Exposure System -----------------------------------------------5-2
Service mode backup ------------------------------------------------------------- 5-2
When clearing the Reader-related RAM data of the
Main Controller PCB. ------------------------------------------------------------- 5-3
Original Exposure and Feed System (Reader) ----------------------------- 5-4
Main Controller -------------------------------------------------------------- 5-15
Main controller PCB --------------------------------------------------------------5-15
DC controller PCB ----------------------------------------------------------------5-16
Control Panel CPU PCB/Touch Panel ---------------------------------------5-16
List of parts that require adjustment after disassembly------------ 5-17
List of parts that require adjustment after disassembly -----------------5-17
Pickup Feed System ------------------------------------------------------- 5-18
Setting method when the size detection patterns are overlapped ----5-18
Cassette Left Edge Margin Adjustment (1st side; Mechanical
Adjsutment) -------------------------------------------------------------------------5-19
Cassette Left Edge Margin Adjustment (1st side; Software
Adjsutment) -------------------------------------------------------------------------5-21
Cassette Left Edge Margin Adjustment (2nd side; Software
Adjsutment) -------------------------------------------------------------------------5-22
Multi-purpose Tray Left Edge Margin Adjustment (1st side;
Software Adjsutment) ------------------------------------------------------------5-22
Multi-purpose Tray Left Edge Margin Adjustment (2nd side;
Software Adjsutment) ------------------------------------------------------------5-22
Lead-edge Margin Adjustment (1st side/normal paper) -----------------5-23
Lead-edge Margin Adjustment (2nd side) ----------------------------------5-23
6 Troubleshooting
Initial Check --------------------------------------------------------------------6-2
Initial check items list ------------------------------------------------------------- 6-2

Test Print ------------------------------------------------------------------------6-3
Overview ----------------------------------------------------------------------------- 6-3
Steps to select the test print PG-TYPE --------------------------------------- 6-3
Troubleshooting Items -------------------------------------------------------6-4
List of Troubleshooting Items --------------------------------------------------- 6-4
Image Failure ----------------------------------------------------------------------- 6-4
Category: Malfunction ----------------------------------------------------------- 6-11
Special Management Mode ---------------------------------------------- 6-12
Overview ----------------------------------------------------------------------------6-12
Operational Description ---------------------------------------------------------6-12
Menu List ----------------------------------------------------------------------------6-13
Version Upgrade ------------------------------------------------------------ 6-15
Overview ----------------------------------------------------------------------------6-15
Preparation -------------------------------------------------------------------------6-15
Downloading System Software ------------------------------------------------6-16
7 Error•Jam•Alarm
Overview ------------------------------------------------------------------------7-2
Outline -------------------------------------------------------------------------------- 7-2
Jam code ----------------------------------------------------------------------------- 7-2
Error Code ----------------------------------------------------------------------7-3
Error Code Details ----------------------------------------------------------------- 7-3
Jam Code --------------------------------------------------------------------- 7-56
Jam Type ----------------------------------------------------------------------------7-56
Alarm Code ------------------------------------------------------------------- 7-67
Alarm Code -------------------------------------------------------------------------7-67
8 Service Mode
Overview ------------------------------------------------------------------------8-2
Service Mode Menu --------------------------------------------------------------- 8-2
Backing up Service Mode -------------------------------------------------------- 8-2
Remote UI service mode --------------------------------------------------------- 8-3
COPIER -------------------------------------------------------------------------8-4
DISPLAY ----------------------------------------------------------------------------- 8-4
I/O -------------------------------------------------------------------------------------8-19
ADJUST -----------------------------------------------------------------------------8-22
FUNCTION -------------------------------------------------------------------------8-72
OPTION -----------------------------------------------------------------------------8-82
COUNTER -------------------------------------------------------------------------8-111
FEEDER --------------------------------------------------------------------- 8-124
ADJUST --------------------------------------------------------------------------- 8-124
FUNCTION ----------------------------------------------------------------------- 8-125
FAX --------------------------------------------------------------------------- 8-126
List of SSSW --------------------------------------------------------------------- 8-126
List of MENU --------------------------------------------------------------------- 8-127
List of NUM ----------------------------------------------------------------------- 8-127
TESTMODE ---------------------------------------------------------------- 8-129
PRINT ------------------------------------------------------------------------------ 8-129
FAX --------------------------------------------------------------------------------- 8-132
9 Installation
How to Check this Installation Procedure -------------------------------9-2
Symbols in the Illustration ------------------------------------------------------- 9-2
Installation ----------------------------------------------------------------------9-2
Copy Control Interface Kit-C1 ----------------------------------------------9-3
Points to Note at Installation ---------------------------------------------------- 9-3
Checking the Contents ----------------------------------------------------------- 9-3
Check Items when Turning OFF the Main Power-------------------------- 9-3
Installation Outline Drawing ----------------------------------------------------- 9-3
Installation Procedure ------------------------------------------------------------- 9-4
MiCARD Attachment Kit-A1 ------------------------------------------------9-9
Checking the Contents ----------------------------------------------------------- 9-9
Points to Note at Installation ---------------------------------------------------- 9-9
Check Items when Turning OFF the Main Power-------------------------- 9-9
Installation Outline Drawing ----------------------------------------------------- 9-9
Installation Procedure ------------------------------------------------------------9-10
Copy Card Reader-F1 ----------------------------------------------------- 9-18
Points to Note at Installation ---------------------------------------------------9-18
Check Items when Turning OFF the Main Power-------------------------9-18
Installation Outline Drawing ----------------------------------------------------9-18
Checking the Contents ----------------------------------------------------------9-18
Installation Procedure ------------------------------------------------------------9-19

Setting After Installation ---------------------------------------------------------9-27
Appendix
Service Tools ----------------------------------------------------------------- 10-2
Special Tools -----------------------------------------------------------------------10-2
Solvents and Oils -----------------------------------------------------------------10-3
General Circuit Diagram --------------------------------------------------- 10-4
Backup Data ------------------------------------------------------------------ 10-5
Soft counter specications ------------------------------------------------ 10-6
Soft counter specications ------------------------------------------------------10-6

■Laser Safety
■Handling of Laser System
■Turn Power Switch ON
■Power Supply
■Safety of Toner
■Notes When Handling a
Lithium Battery
■Notes Before Servicing
■Points to Note at Cleaning
■Notes On Assembly/
Disassembly
Safety Precautions
imageRUNNER C1335/
C1325 Series

0-2
0-2
Laser Safety
Since radiation emitted inside the machine is completely conned within protective housings,
external covers and interlock switches, the laser beam cannot escape from the machine
during any phase of user operation.
Therefore this machine is classied in Class 1 laser products that are regarded as safe during
normal use according to International Standard IEC60825-1.
Handling of Laser System
This machine is classied in Class 1 laser products.
However, inside the machine, Class 3B laser beam is emitted and is hazardous when entered
into an eye.
When servicing the area around the laser assembly, be sure to turn off the main power.
If you must service while the power is turned on, be sure to keep the followings:
- Do not use a screwdriver or tools that have a high level of reectance in the laser path.
- Remove watches and rings before starting the work. (They can reect the laser beam,
possibly hitting an eye.)
The machine's covers that conne laser beam radiation are identied by means of a warning
label (Figure). If you must open the cover and defeat interlock switches, be sure not to enter
the laser beam into an eye during the work.
The following warnings are given to comply with Safety Principles (EN60950-1).
Diese Maschine ist der Klasse 1 der Laserprodukte zugeordnet.
Innerhalb der Maschine wird jedoch ein Laserstrahl der Klasse 3B ausgestrahlt und es ist
gefährlich, wenn dieser Strahl in die Augen gerät.
Bei Servicearbeiten am oder in der Nähe des Laserteils zuerst das Hauptgerät abschalten.
Bei Servicearbeiten, die unbedingt bei eingeschaltetem Gerät durchgeführt werden müssen,
auf jeden Fall die folgenden Vorsichtsmaßnahmen beachten.
- Keine stark reektierenden Schraubenzieher oder ähnliche Werkzeuge direkt in den
Lichtpfad des Laserstrahls bringen.
- Vor Beginn der Arbeit Uhren, Ringe und ähnliche Gegenstände abnehmen. (Reektierende
Laserstrahlen könnten sonst in die Augen geraten.)
Die Geräte-Abdeckungen, die Laserstrahlen reektieren können, werden durch einen
besonderen Warnaufkleber gekennzeichnet (siehe Bild).
Muss die Abdeckung geöffnet und die Sicherheitssperre ausgeschaltet werden, besondere
Vorsicht walten lassen, damit der Laserstrahl nicht in die Augen gerät.
F-0-1

0-3
0-3
Turn Power Switch ON
The machine is equipped with 2 power switches: main power switch and control energy saver
key.
The machine goes on when the main power switch is turned on (i.e., other than in low power
mode, sleep mode).
Main Power Switch
Energy Saver key
CAUTION:
Do not turn off the main power switch while the progress bar is indicated, during
whichaccess is made to the HDD. If deprived of power, the HDD can suffer a fault (E602).
F-0-2
Power Supply
CAUTION:
1. As a general rule, do not use extension cords. Using an extension cord may result
in a re or electrical shock. If an extension cord must be used, however, use one
for local rated voltage and over, untie the cord binding, and insert the power plug
completely into the extension cord outlet to ensure a rm connection between the
power cord and the extension cord.
2. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
F-0-3

0-4
0-4
Safety of Toner
About Toner
The machine's toner is a non-toxic material made of plastic, iron, and small amounts of dye.
CAUTION:
Do not throw toner into re. It may cause explosion.
Toner on Clothing or Skin
• If your clothing or skin has come into contact with toner, wipe it off with tissue; then, wash it
off with water.
• Do not use warm water, which will cause the toner to jell and fuse permanently with the
bers of the cloth.
• Toner is easy to react with plastic material, avoid contact with plastic.
Notes When Handling a Lithium Battery
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The following warnings are given to comply with Safety Principles (EN60950-1).
Achtung:
Wenn mit dem falschen Typ ausgewechselt, besteht Explosionsgefahr.
Gebrauchte Batterien gemäß der Anleitung beseitigen.
Notes Before Servicing
CAUTION:
At servicing, be sure to turn OFF the power source according to the specied steps and
disconnect the power plug.
Points to Note at Cleaning
CAUTION:
When performing cleaning using organic solvent such as alcohol, be sure to check that
the component of solvent is vaporized completely before assembling.

0-5
0-5
Notes On Assembly/Disassembly
Follow the items below to assemble/disassemble the device.
1. Disconnect the power plug to avoid any potential dangers during assembling/disassembling
works.
2. If not specially instructed, reverse the order of disassembly to reinstall.
3. Ensure to use the right screw type (length, diameter, etc.) at the right position when
assembling.
4. To keep electric conduction, binding screws with washers are used to attach the grounding
wire and the varistor. Ensure to use the right screw type when assembling.
5. Unless it is specially needed, do not operate the device with some parts removed.
6. Never remove the paint-locked screws when disassembling.
ACHTUNG
Zweipolige bzw. Neutralleiter-Sicherung
F-0-4
F-0-5
Points to Note when Tightening a Screw
For reduction in weight, thin plates are used in some parts of this machine.
In the case of a screw hole with a triangle mark near it as shown in the gure below, strongly
tightening the screw may damage or deform the screw hole.
In the case of a screw hole with a triangle mark, take care not to apply too much force when
tightening the screw.
The recommended torque value is shown below as a reference value.
Type of Screws
RS tight W Sams Binding TP
Fastened member Metal Resin Metal Resin Metal Resin Metal Resin
Tightening
torque
(N*m)
M4 Approx.
1.6
Approx.
1.6
Approx.
1.6
Approx.
0.8
Approx.
1.6
Approx.
0.8
Approx.
1.6
Approx.
0.8
M3 Approx.
0.8
Approx.
0.8
Approx.
0.6
Approx.
0.6
Approx.
0.6
Approx.
0.6
Approx.
0.6
Approx.
0.6
* For PCB, refer to the tightening torque value of resin (fastened member).
RS tight
Type of Screws
W Sams Binding TP
F-0-6
T-0-1
F-0-7

1
1Product Overview
Product Overview
■Product Lineup
■Features
■Specications
■Parts Name

1
1
1-2
1-2
Product Overview > Product Lineup > Host machine > Model type
Product Overview > Product Lineup > Host machine > Model type
Product Lineup
Host machine
F-1-1
■Host machine conguration
Conguration
Reader+ADF+Printer
■Model type
imageRUNNER C1335 imageRUNNER C1325
Print Speed 35 ppm 25 ppm
T-1-1
T-1-2

1
1
1-3
1-3
Product Overview > Product Lineup > Option > Pickup / Delivery / Image Reading System Options
Product Overview > Product Lineup > Option > Pickup / Delivery / Image Reading System Options
Option
■Pickup / Delivery / Image Reading System Options
[1]
[2]
[3]
[5]
[6]
[8]
[7]
[4]
F-1-2
No. Product name Remarks and condition
1 imageRUNNER C1335/C1325 Series
2 ADF Access Handle-A1
3 Cassette Feeding Unit-AJ1
4 Cassette Feeding Unit-AK1
5 Canon FL Cassette-AV1
6 Cassette Heater Unit-39
7 Copy Card Reader-F1 To install the Copy Card Reader-F1, the Copy Card
Reader Attachment Kit-H1 is required.
8 Copy Card Reader Attachment-H1
T-1-3

1
1
1-4
1-4
Product Overview > Product Lineup > Option > Function expansion system options
Product Overview > Product Lineup > Option > Function expansion system options
■Function expansion system options
License option
[2]
[3]
[1]
F-1-3
●Hardware Products
No. Product name Remarks and condition
1 Super G3 FAX Board-AQ1
2 Copy Control Interface Kit-C1
3 Handset-J1
- eM Controller-C1
●License Products
At the time of installation, obtain the license number according to the license certicate
included. Then, enter the obtained license number from the Control Panel of the machine, so
that the applicable functions are enabled.
There is no physical installation work at the time of intallation.
Product name Remarks and condition
PCL Printer Kit-AZ1
USB Direct Print Kit (for PDF)-K1
Barcode Printing Kit-D1
Universal Send Security Feature Set-E1
T-1-4
T-1-5

1
1
1-5
1-5
Product Overview > Features > Product Features
Product Overview > Features > Product Features
Features
Product Features
Cassette/
Multi-purpose tray Roller
• Longer life
Toner Container
• Reduction in toner soiling
achieved by the new toner
supply system
• Easier replacement
Pickup Roller / Separation
Roller / Separation Pad
ITB Unit
Secondary transfer outer Roller
Drum Unit (Y/M/C/Bk)
Fixing Assembly
Waste Toner Container
• Easier replacement
Improved usability
Improved serviceability
Improved serviceability
Low running cost
F-1-4

1
1
1-6
1-6
Product Overview > Specications > Weight and Size
Product Overview > Specications > Weight and Size
Specications
Specications
Item Specications
Copyboard Original stream reading, original xed reading
Machine installation method Desktop
Light source LED (RGB)
Photosensitive medium OPC
Image reading system CIS
Exposure method Laser exposure
Charging method Roller charging
Developing method Dry, 2-component AC developing
Transfer method Intermediate transfer (ITB)
Separation method Curvature separation + Static Eliminator
Pickup method Cassette: Retard separation
Multi-purpose Tray: Retard separation
Fixing method On-demand xing
Delivery method Face-down
Magnication ratio 25 to 400% (in 1% increment)
Drum cleaning method Cleaning Blade
Transfer cleaning method Cleaning Blade
Toner type Non-magnetic negative toner
Toner supplying method Toner Container method
Toner level detection function Yes
Warm-up time 30 sec. or less
Image gradations 256 gradations
Resolution at writing 600 x 600dpi
First print time imageRUNNER C1335 series CL:10.4 sec. B/W: 8.9 sec.
imageRUNNER C1325 series CL:13.5 sec. B/W: 11.4 sec.
Paper type (Cassette) Thin paper (60 to 63 g/m2), Plain paper 1 (64 to 75 g/m2),
Plain paper 2 (76 to 90 g/m2), Plain paper 3 (91 to 105 g/m2),
Recycled paper, Color paper, Pre-Punched paper,Heavy paper 1
(106 to 128 g/m2), Heavy paper 2 (129 to 163 g/m2), Envelope
Paper type (Multi-purpose Tray) Thin paper (60 to 63 g/m2), Plain paper 1 (64 to 75 g/m2),
Plain paper 2 (76 to 90 g/m2), Plain paper 3 (91 to 105 g/m2),
Recycled paper, Color paper, Heavy paper 1 (106 to 128 g/m2),
Heavy paper 2 (129 to 163 g/m2), Heavy paper 3 (164 to 220 g/
m2), Transparency, Postcard, Envelope
Paper size (Cassette) A4, B5, A5, LGL, LTR, EXEC, STMT, 16K, Envelope
and Custom size (98.4 x 190.5 to 215.9 x 355.6 mm)
Paper size (Multi-purpose Tray) A4, B5, A5, LGL, LTR, EXEC, STMT, 16K, Postcard, Envelope
and Custom size (98.4 x 148 to 215.9 x 355.6 mm)
Pickup capacity Cassette: 550 sheets (80 g/m2)
Multi-purpose Tray: 100 sheets (80 g/m2)
Item Specications
Duplexing method Through-pass duplex
Operation noise 71.5dB or less (during printing)
imageRUNNER C1335 series :71.5dB or less (during printing)
imageRUNNER C1325 series: 68.5dB or less (during printing)
Ozone volume Max 0.001ppm or less
Rated power supply Americas: 120 to 127 V, 60 Hz, 7.5 A
Taiwan: 110 to 120 V, 60 Hz, 7.5 A
Europe/Asia-Oceania/China/Korea/Latin America: 220 to 240 V,
50/60 Hz, 4.0 A
Maximum power consumption Maximum Power Consumption: 1.5 kW or less
Dimensions (W x D x H) imageRUNNER C1335 series: 511mm x 564mm x 610mm
imageRUNNER C1325 series: 511mm x 549mm x 610mm.
Weight Approx. 43kg
Weight and Size
Product name Width
(mm)
Depth
(mm)
Height
(mm)
Weight
Approx. (kg)
imageRUNNER C1335 series 511 564 610 43.0
imageRUNNER C1325 series 511 549 610 43.0
Cassette Module-AJ1 (3 cassette) 511 549 425 14.3
Cassette Module-AK1 (1 cassette) 511 549 425 18.9
T-1-6
T-1-7

1
1
1-7
1-7
Product Overview > Specications > Productivity (Print speed)
Product Overview > Specications > Productivity (Print speed)
Productivity (Print speed)
Paper type Size
imageRUNNER C1335IF imageRUNNER C1325/C1325IF
Cassette Multi-purpose Tray Cassette Multi-purpose Tray
1-sided 2-sided 1-sided 2-sided 1-sided 2-sided 1-sided 2-sided
Thin paper (60 to 63 g/m2)
Plain paper1 (64 to 75 g/m2)
Recycled paper1/Color paper (64 to 75 g/m2)
A4 35 35 30 30 25 25 22 22
LTR 36 36 31 31 26 26 23 23
LGL 29 16 26 15 21 11 19 11
B5/16K 3 to 26 3 to 26 3 to 23 3 to 23 3 to 26 3 to 26 3 to 23 3 to 23
A5R/STMTR 2 to 26 2 to 26 2 to 23 2 to 23 2 to 26 2 to 26 2 to 23 2 to 23
Plain paper2 (76 to 90 g/m2)
Recycled paper2 (76 to 90 g/m2)
Pre-Punched paper (76 to 90 g/m2)
A4 35 35 30 30 25 25 22 22
LTR 36 36 31 31 26 26 23 23
LGL 29 16 26 15 21 11 19 11
B5/16K 3 to 26 3 to 26 3 to 23 3 to 23 3 to 26 3 to 26 3 to 23 3 to 23
A5R/STMTR 2 to 26 2 to 26 2 to 23 2 to 23 2 to 26 2 to 26 2 to 23 2 to 23
Plain paper3 (91 to 105 g/m2)
Recycled paper3 (91 to 105 g/m2)
A4 25 25 22 22 25 25 22 22
LTR 26 26 23 23 26 26 23 23
LGL 21 11 19 11 21 11 19 11
B5/16K 3 to 26 3 to 26 3 to 23 3 to 23 3 to 26 3 to 26 3 to 23 3 to 23
A5R/STMTR 2 to 26 2 to 26 2 to 23 2 to 23 2 to 26 2 to 26 2 to 23 2 to 23
Heavy paper1 (106 to 128 g/m2) A4 17 17 15 15 17 17 15 15
LTR 18 18 16 16 18 18 16 16
LGL 14 8 13 8 14 8 13 8
B5/16K 2 to 18 2 to 18 2 to 16 2 to 16 2 to 18 2 to 18 2 to 16 2 to 16
A5R/STMTR 2 to 18 2 to 18 2 to 16 2 to 16 2 to 18 2 to 18 2 to 16 2 to 16
Heavy paper2 (129 to 163 g/m2)
Label paper (127 to 160 g/m2)
A4 17 17 15 15 17 17 15 15
LTR 18 18 16 16 18 18 16 16
LGL 14 8 13 8 14 8 13 8
B5/16K 2 to 18 2 to 18 2 to 16 2 to 16 2 to 18 2 to 18 2 to 16 2 to 16
A5R/STMTR 2 to 18 2 to 18 2 to 16 2 to 16 2 to 18 2 to 18 2 to 16 2 to 16
Heavy paper3 (164 to 220 g/m2) A4 - - 12 - - - 12 -
LTR - - 12 - - - 12 -
LGL - - 10 - - - 10 -
B5/16K - - 2 to 12 - - - 2 to 12 -
A5R/STMTR - - 2 to 12 - - - 2 to 12 -
Transparency A4 - - 5 - - - 5 -
LTR - - 5 - - - 5 -
Postcard - - - 2 to 16 - - - 2 to 16 -
Envelope Monarch 2 to 18 - 2 to 12 - 2 to 18 - 2 to 12 -
ISO-C5
COM10
DL
T-1-8