Canon PIXMA MX922 Manual

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MX922
Macintosh OS
1

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MX922
Macintosh OS
Preparing to Connect My Multifunction to My Network 3
Network Requirements 3
Notes on Wireless Connection 4
Installing the Drivers 5
2

Preparing to Connect My Multifunction
To My Network << Previous Next >>
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Wireless Connection
Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that
configuration of the computer and access point or router is complete.
3

Preparing to Connect My Multifunction
To My Network << Previous Next >>
4
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of
the network device vary depending on your system environment. For details,
refer to your device's instruction manual or contact its manufacturer.
•In an office setup, consult your network administrator
•If you connect to a network that is not protected with security measures, there
is a risk of disclosing data such as your personal information to a third party.
•If an error message appears or if you have trouble with the network
connection, refer to the printed manual: Network Setup Troubleshooting.
•Place the machine and computer on the same network segment.
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.

Software Installation
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk.
(The installation time varies depending on the computer environment or the number of application software to be installed.)
Installing the Drivers & Software
5
IMPORTANT
•Log on as the administrator (or a member of the Administrators group).
•Quit all running applications before installation.
•Do not switch users during the installation process.
•Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
•It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the
Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
•If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access
the network. If such a warning message appears, set the security software to always allow access.
<< Previous Next >>

6
<< Previous Next >>
1. Insert the CD-ROM into the computer.
IMPORTANT
If the USB cable is already connected, unplug it. If a message appears on the computer, click Cancel.
2. Double-click the [Setup] icon in the CD-ROM folder, then click [Download] in the subsequent window.
Installing the Drivers

7
<< Previous Next >>
REFERENCE
•When the CD-ROM folder does not open automatically,
double-click the CD-ROM icon displayed on the desktop.
•The screen below is displayed while downloading.
Installing the Drivers

8
<< Previous Next >>
If you click [Cancel] while downloading, you will see the following screen.
- If you click [No], you will return to the screen displayed while downloading.
- If you click [Yes], the download is cancelled. In this case, the files under the download are deleted.
When the download fails, the screen below is displayed.
Click [OK], and you will go back to the screen for downloading in the procedure .
Installing the Drivers

9
<< Previous Next >>
3. When the download is complete, the screen below is displayed. Click [Next].
REFERENCE
Select "Save a file for setting up the software again to the download folder after the installation is complete," and the file will be
saved to the download folder.
Installing the Drivers

10
<< Previous Next >>
You can perform the setup later using this file.
Installing the Drivers

11
<< Previous Next >>
5. In the subsequent screen, enter the administrator name and password. Then click [OK].
4. Click Next to install the helper tool.
Connecting to the Wireless Network

12
<< Previous Next >>
6. Continue following instructions. Click Network
Connection on Connection Method Selection
7. Click Wireless Connection*
8. Follow any instructions and Click Connect to the
Network when the Printer Setup window appears .
9. Follow any instructions. Pay particular attention to the
instruction in the Setup Procedure Selection (3-1) if setup
detects a WPS access point. Continue to the next page for
important information on the Setup Procedure Selection. Do
not proceed past the Setup Procedure Selection (3-1) step
until reading the information on the next page.
Connecting to the Wireless Network

10. The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. If a WPS access point is detected, the Push
Button Method screen (shown below on left) will appear on the machine’s operation panel
*Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop
button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*.
If the Push Button Method is not shown on the printer’s operation panel(when no WPS access points have been detected), select Standard
setup on the printers operation panel, then click Other Methods on the Setup Procedure Selection screen
Connecting to the Wireless Network
13
<< Previous Next >>
If you selected the Push Button Method, continue to follow
any instructions until the Completion of Connection screen
appears. Click here to skip ahead to the Completion of
Connection.
If you selected Other Methods, please continue to the next
page for important information

Connecting to the Wireless Network
14
<< Previous Next >>
For Standard setup only
Select Standard setup on the Setup Procedure Selection screen (3-2)
Continue to next page before proceeding any further with setup

Connecting to the Wireless Network
15
<< Previous Next >>
Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and
password information*
Step 4-2 Step 4-4
*Unless you are absolutely certain of this information, please continue to the next page for information on locating /
verifying this information

Connecting to the Wireless Network
16
<< Previous Next >>
If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this
information during Standard setup using the Setup CD-ROM or the downloaded files (Mini Master Setup or Master Setup).
*The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router. "Passphrase' and 'Network
Key' refer to a password required to prevent unauthorized access to communication.
Look for the Confirm the access point name or the Confirm the network key (automatic display) buttons during the setup procedure.
Clicking either of these buttons will give the needed information. On a Mac OS X system you may need to click 'Allow' on one or more
windows after clicking either of the above buttons. See example below of the Wireless Lan Setup Information window. (appearance varies
depending on Operating System). Use the provided information when selecting the Access Point / Router and for entering the Network
Key.

17
<< Previous Next >>Installing the Drivers
11. Continue to follow any instructions until the Setup Completion or Completion of Connection screen below is displayed. Network
connection setting is complete.
Click Next. Software will install. Continue to follow instructions until the Add Printer screen (shown on next page)
appears.

Installing the Drivers & Software
18
<< Previous Next >>
12. Network setup is complete. Continue to follow any remaining On-screen instructions to install the software. On the Software Installation
List screen, select any software to be installed. MP Drivers and Canon IJ Network Tool which are pre-selected are required for the printer to
be able to be used over the network. My Image Garden , Quick Menu and ScanGear are highly recommended to take full advantage of your
printer’s features. Click Next after selecting the software.

19
<< Previous Next >>Installing the Drivers
Add the Printer
1. Click Add Printer on the Add Printer Screen

20
<< Previous Next >>Installing the Drivers
2. Select Canon MX920 series with Canon IJ Network listed in the Kind column*. Click Add.
*CAUTION
If you will be installing the Canon printer driver on Mac OS X and using the printer through a network connection, you can select
[Bonjour] or [Canon IJ Network] in the [Add Printer] dialog.
If [Bonjour] is selected, remaining ink level messages may differ from those indicated by [Canon IJ Network].
Canon recommends you to use [Canon IJ Network] for printing.
REFERENCE
If the machine is not detected, make sure of the following:
- The machine is turned on.
- The firewall function of any security software is turned off.
-The computer is connected to the access point.