Canon LM-V1 User manual

SAFETY INSTRUCTIONS
2EN
EN
Safety Instructions
Be sure to read these instructions in order to operate the product safely. Follow these instructions to
prevent injury or harm to the operator of the product or others.
WARNING
Denotes the risk of serious injury or death.
•Keep the product out of the reach of young children.
•Do not disassemble or modify the product.
•Do not expose the product to strong shocks or vibration.
•Do not touch any exposed internal parts.
•Stop using the product in any case of unusual circumstances such as the presence of smoke or a
strange smell.
•Do not get the product wet. Do not insert foreign objects or liquids into the product.
CAUTION
Denotes the risk of injury.
•Do not leave the product in places exposed to extremely high or low temperatures. The product may
become extremely hot/cold and cause burns or injury when touched.
For accessories with screens/viewfinders
CAUTION
Denotes the risk of injury.
•Do not look at the screen or through the viewfinder for prolonged periods of time. This may induce
symptoms similar to motion sickness. In such a case, stop using the product immediately and rest for a
while before resuming use.
For accessories with an eyecup
CAUTIONS
Follow the cautions below. Otherwise physical injury or property damage may result.
•If any abnormal skin reaction or irritation occurs during or following the use of this product, refrain from
further use and get medical advice/attention.
For lens mount kits
WARNING
Denotes the risk of serious injury or death.
•Do not leave the lens exposed without the lens cap attached.
•Be careful not to drop the camera or accessories when attaching, removing or adjusting the
various accessories. Use a table or other stable surface.
•Do not connect/attach accessories to cameras and devices that are not compatible with them.

TABLE OF CONTENTS
3EN
2 Safety Instructions
4Introduction
5 Overview of Accessories and Compatible Cameras
6 Communications
6 GP-E1 GPS Receiver
7 GP-E2 GPS Receiver
9 WFT-E6 / WFT-E8 Wireless File Transmitter
10 Monitoring
10 LM-V1 / LM-V2 LCD Monitor
14 EVF-V50 OLED Electronic Viewfinder
17 EVF-V70 OLED Electronic Viewfinder
21 Added Functionality and Lens Compatibility
21 OU-700 Remote Operation Unit
25 EU-V1 Expansion Unit 1
28 EU-V2 Expansion Unit 2
35 MO-4E / MO-4P B4 Mount Adapter
38 CM-V1 EF Cinema Lock Mount Kit
38 PM-V1 PL Mount Kit
43 Shooting Styles and Configuration
43 GR-V1 Camera Grip
46 SU-15 Shoulder Support Unit
49 SG-1 Shoulder Style Grip Unit
Table of Contents

INTRODUCTION
4EN
Introduction
This user guide covers optional accessories compatible with CINEMA EOS series Canon cameras. It
provides information about how to use the accessories, their compatibility and specifications. Be sure to
read this information carefully to use the products correctly.
Before Using the Accessories
•Do not point monitors or viewfinders toward an intense light source, such as the sun on a sunny day or
an intense artificial light source. Doing so may damage the LCD screen/OLED screen or other internal
components. Change the accessory’s angle so that it is not pointing at the light source.
•LCD and OLED screens are produced using extremely high-precision manufacturing techniques, with
more than 99.99% of the pixels operating to specification. Very rarely, pixels may misfire or may light up
permanently. This has no effect on the recorded image and does not constitute a malfunction.
•Unless specified otherwise, power to the accessories is supplied by the camera.
•Your camera may not support all the camera features and functions described in this guide. Refer also to
the instruction manual of the camera being used.
•Some of the accessories and tools mentioned in the procedures in this guide may be supplied with
some camera models. Check the list of supplied accessories in the instruction manual of the camera
being used.
If an accessory/tool is not supplied with the camera or with the product being explained, please use an
optional accessory or commercially available product.
Conventions in this Document
•Important precautions related to the product’s operation.
•Additional information that complements the basic operation procedures.
•0Reference page number in this document.
•“Camera” refers to a compatible Canon camera or camcorder (05).
•This is a multilingual document. You can click on the language code on any page to return
to the beginning of the guide (Table of Contents) in that language.
EN

OVERVIEW OF ACCESSORIES AND COMPATIBLE CAMERAS
5EN
Overview of Accessories and Compatible
Cameras
1Only the LM-V1 LCD Monitor is compatible.
2For details see the instruction manual of the camera being used and the RC-V100 instruction manual.
3The MO-4P B4 mount adapter can only be used after replacing the camera’s lens mount with a PL mount using the
optional PM-V1 PL Mount Kit (038).
4For details see the instruction manual of the camera being used.
The information in this document is verified as of November 2019. Subject to change without previous
notice.
Accessory EOS C100
Mark II
EOS C200
EOS C200B
EOS C500
Mark II
EOS C700
all models 0
Communications
GP-E1 GPS Receiver — — — N6
GP-E2 GPS Receiver NNN—7
WFT-E6 / WFT-E8 Wireless File Transmitter — — — N9
Monitoring
LM-V1 / LM-V2 LCD Monitor — N1N—10
EVF-V50 OLED Electronic Viewfinder — — N—14
EVF-V70 OLED Electronic Viewfinder — NNN17
Added Functionality and Lens Compatibility
RC-V100 Remote Operation Unit NNNN—2
OU-700 Remote Operation Unit — — — N21
EU-V1 Expansion Unit 1 — — N—25
EU-V2 Expansion Unit 2 — — N—28
MO-4E / MO-4P B4 Mount Adapter — — N3N35
CM-V1 EF Cinema Lock Mount Kit ——N—38
PM-V1 PL Mount Kit
CDX-36150 Codex Recorder for Canon EOS C700 — — — N—4
Shooting Styles and Configuration
GR-V1 Camera Grip — NN—43
SU-15 Shoulder Support Unit — NNN46
SG-1 Shoulder Style Grip Unit — — NN49

COMMUNICATIONS
6EN
Communications
GP-E1 GPS Receiver
Connect the GPS receiver to the camera’s system expansion terminal in CAMERA (shooting) mode to
have the GPS information (latitude, longitude, altitude) recorded with the metadata of XF-AVC clips. For
details about attaching and configuring the receiver, refer to the instruction manual of the camera being
used.
•In certain countries/regions, the use of GPS may be restricted. Be sure to use the GPS receiver
in accordance with local laws and regulations of the country/region where the receiver is used.
Be particularly careful when traveling outside of your home country.
•Be careful about using GPS functions where the operation of electronic devices is restricted.
•The GPS information recorded with clips may contain data that can lead others to locate or
identify you. Be careful when sharing geotagged recordings with others or when uploading
them to the Web.
•Do not leave the receiver near strong electromagnetic fields such as near powerful magnets
and motors.
•The GPS information recorded with clips corresponds to the location at the start of the
recording.
•Initial GPS signal reception will take longer after replacing the receiver’s battery or when first
turning on the receiver after a prolonged period of having been turned off.
•Do not place cables connected to the camera’s terminals near the receiver. Doing so may
negatively affect the GPS signal.
(attach directly)
System expansion terminal

COMMUNICATIONS
7EN
GP-E2 GPS Receiver
Connect the GPS receiver to the camera’s USB terminal in CAMERA (shooting) mode to have the GPS
information (latitude, longitude, altitude) recorded with the metadata of clips and photos. While recording, it
is recommended to place the receiver in the supplied carrying case and attach it to the camera’s grip belt
or carry it on your person.
For details about attaching and configuring the receiver, refer to the GP-E2’s instruction manual.
Recorded Information
* You can use the GPS information to search and organize clips using Canon XF Utility.
Connecting and Activating the GPS Receiver
1. Turn off the receiver.
2. Connect the receiver to the camera.
•Use the USB cable supplied with the GP-E2.
3. Turn on the receiver.
•The GPS function is activated. The icon appears on the screen and will flash as the receiver tries
to acquire satellite signals.
•When satellite signals are correctly acquired, the icon will stay continuously on. Clips and photos
recorded after that will be geotagged.
Recording format GPS information
(latitude, longitude, altitude)
Coordinated universal time
(UTC)
Clips
MP4 NN
AVCHD NN
XF-AVC* N—
RAW
(Cinema RAW Light) NN
Photos NN
USB cable (supplied with the GP-E2)
USB terminal

COMMUNICATIONS
8EN
•In certain countries/regions, the use of GPS may be restricted. Be sure to use the GPS receiver
in accordance with local laws and regulations of the country/region where the receiver is used.
Be particularly careful when traveling outside of your home country.
•Be careful about using GPS functions where the operation of electronic devices is restricted.
•The GPS information recorded with clips and photos may contain data that can lead others to
locate or identify you. Be careful when sharing geotagged recordings with others or when
uploading them to the Web.
•Do not leave the receiver near strong electromagnetic fields such as near powerful magnets
and motors.
•The GPS information recorded with clips corresponds to the location at the start of the
recording.
•You can have the camera’s date and time settings adjusted automatically according to the
information received from the GPS signal. See the [System Setup] menu settings’ table in the
instruction manual of the camera being used.
•Initial GPS signal reception will take longer after replacing the receiver’s battery or when first
turning on the receiver after a prolonged period of having been turned off.
•Do not place cables connected to the camera’s terminals near the receiver. Doing so may
negatively affect the GPS signal.
•Cameras with status screens only: You can check the GPS information being received and the
satellite’s signal strength on the status screens. For details see the instruction manual of the
camera being used.
•The camera is not compatible with the following receiver functions.
– The [Set now] option for the automatic date adjustment function
– Digital compass function
– Positioning interval function

COMMUNICATIONS
9EN
WFT-E6 / WFT-E8 Wireless File Transmitter
Connect the wireless transmitter to the camera’s system expansion terminal to be able to connect to a
wireless network or device via Wi-Fi and use the camera’s network functions. For details about attaching
and configuring the wireless transmitter, refer to the instruction manual of the camera being used.
•Do not place cables connected to the camera’s terminals near the receiver. Doing so may
negatively affect the wireless signal.
(attach directly)
System expansion terminal

MONITORING
10 EN
Monitoring
LM-V1 / LM-V2 LCD Monitor
Connect the LCD monitor to the camera to add a large monitoring screen with touch screen operations
(touch to focus), menu operation buttons and joystick and two assignable buttons.
For details on how to attach and use the LCD monitor, see the instruction manual of the camera being
used.
An optional attachment unit is also required to attach the monitor to the camera.
Names of Parts
1 LCD panel with touch screen
2 FUNC (main functions) button / Assignable
button LCD LM-V1/V2 1
3MENUbutton
4Joystick
5 MIRROR (invert the displayed image) button
6CANCELbutton
7 DISP (display) button / Assignable button LCD
LM-V1/V2 2
8 LCD monitor’s position alignment mark Í
9 Screw holes for 1/4"-20 screws (11.2 mm
(0.44 in.) deep, x2)
10 VIDEO terminal
VIDEO terminal
UN-5 / UN-10 Unit Cable (optional)
1
2
3
4
5
6
7
8
9
10

MONITORING
11 EN
Attaching the LCD Monitor
About the LCD Attachment Unit
Use the optional LA-V1 or LA-V2 LCD Attachment Unit to attach the LCD monitor to the handle unit or to
the camera’s body itself. For details see the instruction manual of the camera being used.
Attaching the LCD Monitor to the Handle Unit
1. Turn off the camera.
2. On the LCD attachment unit, rotate the LCD
monitor mount in the direction of the locking knob
to make the LCD monitor fixation bolt accessible.
3. Attach the LCD monitor to the LCD monitor mount.
•Align the Ímarks on the monitor and monitor
mount. If necessary, you can also mount the LCD
monitor facing the other way around.
•Tighten the LCD monitor fixation bolt using the hex
wrench for 0.64 cm, 1/4" screws.
4. Attach the LCD attachment unit to the handle unit.
•Align the attachment mount on the LCD attachment
unit to the handle unit’s front accessory mount.
•Tighten the locking knob firmly.
5. Rotate the LCD monitor 90 degrees toward the
handle unit.
6. Connect the LCD monitor to the camera’s VIDEO
terminal using the UN-5 Unit Cable.
•Align the Ímarks on the cable’s plugs and
terminals.
7. Put the cable though the LCD attachment unit’s
cable clamp.
•If necessary, adjust the position of the cable so that
it does not get in the picture or obstruct the view.
LCD Monitor
LM-V1 LM-V2
LCD Attachment Unit LA-V1 N—
LA-V2 —N
햴햳
햶
햵
햸
햷
햷