Canon DP-V1830 User manual

• Beforeuse,besuretoreadthisguide,includingthesafetyandhandlingprecautions.
• Readingthisguidewillhelpyoulearntousethevideodisplayproperly.
• Storethisguidesafelysothatyoucanuseitinthefuture. English
Instruction Manual
Operation Guide
Video Display
Firmware ver. 1.0

2
Table of Content
Introduction 3
Aboutthismanual  3
Trademarks  3
Operating the Video Display 4
BasicoperationstousetheOSDmenu  4
AdjustingImageQualityWhileViewingthe
EntireImage  5
TemporarilySavingParameters(AnchorPoint
Setting)  7
Enlargingthedisplay(Zoomfunction)  7
ChangingImageQualityAutomatically
AccordingtoInputSignal  8
Changingthescreendisplayarea  8
Export/Import  9
SetDate/Time  11
InputtingCharacters  12
UsingtheFunction(F)Buttons  13
UsingtheChannel(CH)Button  14
CheckingSignalInformationandStatusofthe
MainUnit  17
Operatingthevideodisplayusinganexternal
device[GPIterminal]  17
Operatingthevideodisplayusinganexternal
device[LANterminal]  18
OSD Menu 19
Adjustment  19
ChannelSettings  34
DisplaySettings  37
AudioSettings  39
MarkerSettings  40
FunctionSettings  47
PictureFunctionSettings  56
Network/IMDSettings  60
SystemSettings  61
SignalInformation  68
SystemInformation  68
Supported Signal Format 69
Image/Frame Display 83
Error Messages 86
Troubleshooting 89
Software Used in This Product 91
Index 95
About the User Manual for the Display
• TheproductincludesanInstructionManualorSetupGuide.Beforeusingtheproduct,besuretoread
“ImportantUsageInstructions”and“SafetyInstructionsandHandlingPrecautions”.
• TheOperationGuide(thisdocument)explainsthefunctionsavailableontheversionofthermwareshownon
thecoverpageaswellassetupprocedures.

3
Introduction
TheOnScreenDisplay(thereafterreferredtoOSD)defaultlanguagesettingisEnglish.TochangetheOSDmenu
languagesetting,pleaserefertop.61.
About this manual
ThescreenoftheDP-V1830isusedasanexampleinthisGuide.SomeoftheillustrationusedintheGuidehavebeen
simpliedforclarity.
Conventions used in this manual
:Indicatesareferencepage.
Reference:Indicatesreferenceinformation.
CAUTION:Indicatesanitemyoumustobserve.
Note:Indicatesanote.
 [Adjustment] [PictureMode]:
PressingtheMENUbuttonshowstheOSDMenulevels.Youcanmovebetweentheitemsandselectfromthem.
Trademarks
• HDMI,HDMIlogo,andHigh-DenitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMI
LicensingAdministrator,Inc.intheU.S.andothercountries.
• VESAisaregisteredtrademarkortrademarkofVideoElectronicsStandardsAssociationintheU.S.andother
countries.
• Otherproductandcompanynameshereinaretrademarksorregisteredtrademarksoftheirrespectiveowners.

4
OperatingtheVideoDisplay
Usingbuttonsandjogdialonthevideodisplay,youcanadjustimagequalityandconguresettingsforinputsignals.In
addition,youcanassignfrequentlyusedfunctionstotheCH(Channel)andF(Function)buttons.
Basic operations to use the OSD menu
ThevideodisplaysettingsarechangedfromtheOSDmenu.
MENU button
Opens/closestheOSD
menu,ormovesupone
levelinamenu.
RESET button
Resetstheitemstobeadjustedusingthesliderand
enteredcharacters.
Jog dial
 
orrotation:Usedtomovetoadifferentitemandchange
settings.
Press: Conrmssettingsormovestheselection
frameup/down1level.
1 Open the OSD menu.
•PresstheMENUbutton.
2 Select the Main Menu.
•SelecttheMainMenuitemusingthejogdialandpressitto
determinetheselection.
3 Select the Sub Menu.
•SelecttheSubMenuitemusingthejogdialandpressitto
determinetheselection.
MainMenu SubMenu SettingOptions

Operating the Video Display
5
4 Select the setting to change.
•Selectthesettingtochangeusingthejogdialandpressitto
determinetheselection.YouwillbereturnedtotheSubMenu
itemselectionscreen.
5 Exit menu.
•PressingtheMENUbuttonwillreturnyoutotheMainMenu
itemselectionscreen.PressingtheMENUbuttonagainwill
closethemenuscreen.
Note
• Toadjustimagequality,warming-upisnecessarytostabilizethebrightnessofthevideodisplay.Waitatleast10minutesafter
turningonthepowerbeforeuse.
• TheOSDmenuandsliderwilldisappearautomaticallyifnooperationisperformedforapproximately1minute.Thefunction
buttonguigewilldisappearautomaticallyifnooperationisperformedforapproximately10seconds.
• Thesettingsthatcannotbeset,aregrayedout.
• Thefollowingfunctionscanbereturnedtotheirfactorydefaultsettingsortheiranchorpoint( 7)bypressingtheRESETbutton,
afteradjustingtheimagequality.
- [Luminance],[Brightness],[Chroma],[HDRRange],[Power],[Saturation],[Offset],[Slope]
When[PictureMode] [User1–9]:Whenexecutingcalibration,pressingtheRESETbuttonwhileadjustingtheimagequalitywill
returnyoutothesettingsaftercalibration.
Adjusting Image Quality While Viewing the Entire Image
YoucanadjusttheOSDmenutodisplayasaslideratthebottomofthescreen.Thisallowsfortheimagequalitytobe
adjustedwhilstitisdisplayedonthescreen.
1 Press the jog dial when the selection frame is on setting options.
•Asliderappearsatthebottomofthescreen.
2 Make adjustments using the jog dial with using the slider as
guide.
3 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.

Operating the Video Display
6
Color temperature detailed settings (gain, bias)
YoucanadjustRGBallatonceorindividuallywhenthescreensforadjusting[Gain]or[Bias]aredisplayed.
1 Select [Adjustment] [Color Temperature].
•[GainR],[GainG],[GainB],[BiasR],[BiasG],and[BiasB]canbesetindividuallyusingthejogdial(  ).
2 Select one.
•Thesettingscreenfor[Gain]or[Bias]willbedisplayed.
3 Switch the guide in the upper right area of the slider screen using the jog dial ( ).
•Theindicationchangesto[RGB],[R],[G],and[B].Selecting[RGB]willallowyoutoadjustRGBasawhole.
4 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Color temperature detailed settings (xy values)
1 Select [Adjustment] [Color Temperature].
2 Select [Custom (xy)].
•Youcanset[x]and[y]individuallyusingthejogdial(  ).
3 Select either [x] or [y].
•Thecolormapisdisplayed.
4 Adjust [x] with the and [y] with .
•Theadjustedvalueisindicatedbythe" "markonthecolormap.
5 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Defaultvalue
Lastusedvalue
Currentvalue
Currentvalue

Operating the Video Display
7
Temporarily Saving Parameters (Anchor Point Setting)
Youcantemporarilysaveparametersfor[Luminance],[Brightness],[Chroma],and[HDRRange].See 25forsetting
anchorpointsduringCDLadjustment.
1 Select [Adjustment] [Anchor Adjustment].
2 Press the jog dial, and when the confirmation screen appears, select [OK].
•Theparameterissavedandtheanchorpointisset.
3 Adjust the image quality again and press the RESET button on the video display.
•Returnsyoutotheanchorpointforeachfunction.
CurrentvalueLastusedvalue
Anchorpoint
Note
• Executing[Adjustment] [Reset]or[SystemSettings] [ResetAllSettings]resetssavedanchorpointsandthesettingsreturn
totheirfactorydefaultvalues.
Enlarging the display (Zoom function) ( 38)
Thezoomdisplaypositioncanbeadjusted,andthezoommagnication(2x,4x,8x)canbeselected.
1 Select [Display Settings] [Zoom].
2 Select [Zoom Preset].
•Selectapresetzoomdisplay.
3 Select [Position].
•Thezoomadjustmentscreenisdisplayed.
- Tomovethedisplayposition:Movethejogdial(  orrotation).
- Toreturntothecenter:PresstheRESETbutton.
4 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Note
• WhenmagnifyingtheimageandtheOSDmenuisnotbeingdisplayed,
- youcansetthemagnicationratiobypressingthejogdial.
- Youcanmovethedisplaylocationbymovingthejogdial(  orrotation).
- YoucansetthefollowingfunctionsusingtheCHbutton:
CH1:Selectzoommagnication;CH2:Switchbetweenzoompresets(Zoom1/Zoom2/Zoom3);CH3:Zoomoff
Zoom 2 [x4]

Operating the Video Display
8
Changing Image Quality Automatically According to Input Signal
Onthisvideodisplay,youcanautomaticallychangetheimagequalityaccordingtovideoresolutionormetadata.
Changing [Picture Mode] automatically ( 36)
1 Select [Channel Settings] [Select Channel].
•Selectthechannel.
2 Select [Channel Settings] [Picture Mode] [Type].
3 Select the Type using the jog dial.
Changing by individual video resolution (4K/2K)
Select[4K/2K].
Changing according to video resolution (4K/2K) or metadata (SDI)
Select[Automatic].
4 Select the Picture Mode.
Changing the image quality setting according to video metadata (HDMI) ( 28)
1 Select [Adjustment] [Picture Mode] [User 1] - [User 9].
2 Select [Adjustment] [Detail Settings] [HDMI Link] [Automatic Adjustment].
•Select[On].
•See[HDMILink]( 28)forthecongurablesettings.
Note
• Whenautomaticchangingofimagequalityaccordingtovideoresolution(4K/2K)orSDImetadataisset,
informationshowingwhichresolution(4K/2K,etc.)isselectedwillbedisplayedatthetoprightofthe
menuscreen.
Changing the screen display area
When4096x2160videosignalisinput,theleftandrightsidesoftheimagewillbecroppedtodisplayanareaof
3840x2160.Thecroppedsidescanthenbefurtheradjustedontheleftandright.
1 Select [Display Settings] [Screen Scaling].
•Select[NativeInputResolution]or[200%].
2 Press the jog dial ( ) while the OSD menu is closed.
•Shiftstotheleftorright.

Operating the Video Display
9
Export/Import
Youcanexport/importLUTandCDLparametersaswellasOSDmenusettings.
LUT Import ( 26)
1 Insert the USB memory stick containing the LUT file into the USB port of the video display.
2 Select [Adjustment] [Detail Settings] [LUT Import].
3 Select the LUT file to import.
•Inthe[Filename]eld,searchanddisplayalewithextension".clut"and".cube"intherootfolder.
4 Select the LUT type.
•Refertothe"ConceptDrawingofDisplayImageProcessingandLUT"( 10).
5 Select the LUT No. to save the LUT.
6 Select [Execute].
•Whentheconrmationscreenappears,select[OK].Importstarts.
Note
• Importof[3D-LUT]canalsobesetfrom[Adjustment] [CDL/UserLUT] [3D-LUT] [LUTImport].
• TheLUTle(.clutformat)isproprietarytoCanonVideoDisplay.RefertotheCanonwebsitefortheleformatandhowtocreate
theLUTle.
• Upto1000LUTimportlesarerecognized.
• YoucandeletetheimportedLUT,aswellasrenametheLUT( 26).
ThecongurationofLUTles(cubeformat)isshownbelow.
LUT filename
Type of characters that can be used One-bytealphabeticalcharactersandnumbersonly
No. of characters that can be used Upto64characters(includingtheextension)
Extension .cube
LUT file format
TITLE ASCII24characterscanbeused.
*DisplayedintheOSDmenuofthedisplayasaselectionitem.(Upto24characters)
LUT_3D_SIZE Specifyonefrom9/17/33/65.
Table Data SpecifyRed,GreenandBlue.
LUT_1D_SIZE
DOMAIN_MIN
DOMAIN_MAX
LUT_1D_INPUT_RANGE
LUT_3D_INPUT_RANGE
Unsupported.
• Forthelinefeedcode,use“CR(carriagereturn)”,“LF(linefeed)”,or“CR+LF”.
• Forthecharactercode,use“Shift-JIS”,“EUC-JP”,or“UTF-8(with/withoutBOM)”.
• Filesinwhichboth1D-LUTand3D-LUTarewrittenarenotsupported.

Operating the Video Display
10
Concept Drawing of Display Image Processing and LUT
Color Gamut/Gamma/
HDR Range, etc.
Range
conversion
Range
conversion
3D-LUT
Import
LUT Preset
Export/Import OSD Menu Settings ( 64)
1 Select [System Settings] [Export/Import].
2 Select [Export] or [Import].
Exporting
1Select[Target]from[USB]or[User1]to[User3].
Export[USB]totheUSBmemoryand[User1]to[User3]tothebuilt-inmemoryofthemainunit.
2Ifyouselected[USB],select[Filename].
• Thefactorydefaultis[dinfo_dpv****.dat](****:Numberoftheproductname).Youcanchangethenameof
theletobeexportedtotheUSBmemorywithin16one-bytecharactersincludingalphabeticalcharacters,
numbers,andsymbols.
Importing
1Select[Target]from[USB]or[User1]to[User3].
Specifythedestinationtosavetheletobeimported.
2Select[Filename]when[USB]isselected.
3In[Settings],select[All]orMainMenuname.
3 Select [Execute].
•Whentheconrmationscreenappears,select[OK].Export/Importstarts.
Note
• Afterexportto[User1]to[User3],youcanselectthecongurationsatstartupfrom[User1]to[User3]in[PoweronSetting]in
[SystemSettings]( 64).