Canon DP-V2730 User manual

• Beforeuse,besuretoreadthisguide,includingthesafetyandhandlingprecautions.
• Readingthisguidewillhelpyoulearntousethevideodisplayproperly.
• Storethisguidesafelysothatyoucanuseitinthefuture. English
Instruction Manual
Operation Guide
Video Display
Firmware ver. 1.1
Firmware ver. 1.0

2
Table of Content
Introduction 3
Aboutthismanual  3
Trademarks  3
Operating the Video Display 4
BasicoperationstousetheOSDmenu  4
AdjustingImageQualityWhileViewingthe
EntireImage  5
TemporarilySavingParameters(AnchorPoint
Setting)  7
Enlargingthedisplay(Zoomfunction)  7
ChangingImageQualityAutomatically
AccordingtoInputSignal  8
Changingthescreendisplayarea  8
Export/Import  9
SetDate/Time  11
InputtingCharacters  12
UsingtheFunction(F)Buttons  13
UsingtheChannel(CH)Button  14
CheckingSignalInformationandStatusofthe
MainUnit  16
Operatingthevideodisplayusinganexternal
device[GPIterminal]  16
Operatingthevideodisplayusinganexternal
device[LANterminal]  17
Useawebbrowsertoremotelyoperatethe
videodisplay  18
OSD Menu 21
Adjustment  21
ChannelSettings  36
DisplaySettings  41
AudioSettings  44
MarkerSettings  45
FunctionSettings  52
PictureFunctionSettings  64
Network/IMDSettings  68
SystemSettings  70
SignalInformation  76
SystemInformation  76
Supported Signal Format 77
Image/Frame Display 91
Error Messages 94
Troubleshooting 97
Software Used in This Product 99
Index 103
About the User Manual for the Display
• TheproductincludesanInstructionManualorSetupGuide.Beforeusingtheproduct,besuretoread
“ImportantUsageInstructions”and“SafetyInstructionsandHandlingPrecautions”.
• TheOperationGuide(thisdocument)explainsthefunctionsavailableontheversionofthermwareshownon
thecoverpageaswellassetupprocedures.

3
Introduction
TheOnScreenDisplay(thereafterreferredtoOSD)defaultlanguagesettingisEnglish.TochangetheOSDmenu
languagesetting,pleaserefertop.70.
About this manual
ThescreenoftheDP-V1830isusedasanexampleinthisGuide.SomeoftheillustrationusedintheGuidehavebeen
simpliedforclarity.
Conventions used in this manual
:Indicatesareferencepage.
Reference:Indicatesreferenceinformation.
CAUTION:Indicatesanitemyoumustobserve.
Note:Indicatesanote.
 [Adjustment] [PictureMode]:
PressingtheMENUbuttonshowstheOSDMenulevels.Youcanmovebetweentheitemsandselectfromthem.
• Thefollowingsymbolsshowdifferencesinfunctionsandsettingsdependingontheproduct.
 :Explanationsareapplicabletotheindicatedproducts.
Trademarks
• HDMI,HDMIlogo,andHigh-DenitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMI
LicensingAdministrator,Inc.intheU.S.andothercountries.
• VESAisaregisteredtrademarkortrademarkofVideoElectronicsStandardsAssociationintheU.S.andother
countries.
• AppleandSafariaretrademarksofAppleInc.registeredintheUnitedStatesandothercountries.
• GoogleandGoogleChromearetrademarksorregisteredtrademarksofGoogleLLC.
• Otherproductandcompanynameshereinaretrademarksorregisteredtrademarksoftheirrespectiveowners.

4
OperatingtheVideoDisplay
Usingbuttonsandjogdialonthevideodisplay,youcanadjustimagequalityandconguresettingsforinputsignals.In
addition,youcanassignfrequentlyusedfunctionstotheCH(Channel)andF(Function)buttons.
Itemsthatcannotbesetduetootherfunctionsettingsarehiddenorgrayedout.
Basic operations to use the OSD menu
ThevideodisplaysettingsarechangedfromtheOSDmenu.
MENU button
Opens/closestheOSD
menu,ormovesupone
levelinamenu.
RESET button
Resetstheitemstobeadjustedusingthesliderand
enteredcharacters.
Jog dial
 
orrotation:Usedtomovetoadifferentitemandchange
settings.
Press: Conrmssettingsormovestheselection
frameup/down1level.
1 Open the OSD menu.
•PresstheMENUbutton.
2 Select the Main Menu.
•SelecttheMainMenuitemusingthejogdialandpressitto
determinetheselection.
3 Select the Sub Menu.
•SelecttheSubMenuitemusingthejogdialandpressitto
determinetheselection.
MainMenu SubMenu SettingOptions

Operating the Video Display
5
4 Select the setting to change.
•Selectthesettingtochangeusingthejogdialandpressitto
determinetheselection.YouwillbereturnedtotheSubMenu
itemselectionscreen.
5 Exit menu.
•PressingtheMENUbuttonwillreturnyoutotheMainMenu
itemselectionscreen.PressingtheMENUbuttonagainwill
closethemenuscreen.
Note
• Toadjustimagequality,warming-upisnecessarytostabilizethebrightnessofthevideodisplay.Waitatleast10minutesafter
turningonthepowerbeforeuse.
• TheOSDmenuandsliderwilldisappearautomaticallyifnooperationisperformedforapproximately1minute.Thefunction
buttonguigewilldisappearautomaticallyifnooperationisperformedforapproximately10seconds.
• Thesettingsthatcannotbeset,aregrayedout.
• Thefollowingfunctionscanbereturnedtotheirfactorydefaultsettingsortheiranchorpoint( 7)bypressingtheRESETbutton,
afteradjustingtheimagequality.
- [Luminance],[Brightness],[Chroma],[HDRRange],[Power],[Saturation],[Offset],[Slope]
When[PictureMode] [User1–9]:Whenexecutingcalibration,pressingtheRESETbuttonwhileadjustingtheimagequalitywill
returnyoutothesettingsaftercalibration.
Adjusting Image Quality While Viewing the Entire Image
YoucanadjusttheOSDmenutodisplayasaslideratthebottomofthescreen.Thisallowsfortheimagequalitytobe
adjustedwhilstitisdisplayedonthescreen.
1 Press the jog dial when the selection frame is on setting options.
•Asliderappearsatthebottomofthescreen.
2 Make adjustments using the jog dial with using the slider as
guide.
3 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.

Operating the Video Display
6
Color temperature detailed settings (gain, bias)
YoucanadjustRGBallatonceorindividuallywhenthescreensforadjusting[Gain]or[Bias]aredisplayed.
1 Select [Adjustment] [Color Temperature].
•[GainR],[GainG],[GainB],[BiasR],[BiasG],and[BiasB]canbesetindividuallyusingthejogdial(  ).
2 Select one.
•Thesettingscreenfor[Gain]or[Bias]willbedisplayed.
3 Switch the guide in the upper right area of the slider screen using the jog dial ( ).
•Theindicationchangesto[RGB],[R],[G],and[B].Selecting[RGB]willallowyoutoadjustRGBasawhole.
4 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Color temperature detailed settings (xy values)
1 Select [Adjustment] [Color Temperature].
2 Select [Custom (xy)].
•Youcanset[x]and[y]individuallyusingthejogdial(  ).
3 Select either [x] or [y].
•Thecolormapisdisplayed.
4 Adjust [x] with the and [y] with .
•Theadjustedvalueisindicatedbythe" "markonthecolormap.
5 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Defaultvalue
Lastusedvalue
Currentvalue
Currentvalue

Operating the Video Display
7
Temporarily Saving Parameters (Anchor Point Setting)
Youcantemporarilysaveparametersfor[Luminance],[Brightness],[Chroma],and[HDRRange].See 27forsetting
anchorpointsduringCDLadjustment.
1 Select [Adjustment] [Anchor Adjustment].
2 Press the jog dial, and when the confirmation screen appears, select [OK].
•Theparameterissavedandtheanchorpointisset.
3 Adjust the image quality again and press the RESET button on the video display.
•Returnsyoutotheanchorpointforeachfunction.
CurrentvalueLastusedvalue
Anchorpoint
Note
• Executing[Adjustment] [Reset]or[SystemSettings] [ResetAllSettings]resetssavedanchorpointsandthesettingsreturn
totheirfactorydefaultvalues.
Enlarging the display (Zoom function) ( 42)
Thezoomdisplaypositioncanbeadjusted,andthezoommagnication(2x,4x,8x)canbeselected.
1 Select [Display Settings] [Zoom].
2 Select [Zoom Preset].
•Selectapresetzoomdisplay.
3 Select [Position].
•Thezoomadjustmentscreenisdisplayed.
- Tomovethedisplayposition:Movethejogdial(  orrotation).
- Toreturntothecenter:PresstheRESETbutton.
4 When adjustments are completed, press the jog dial.
•ThescreenreturnstotheoriginalOSDmenu.
Note
• WhenmagnifyingtheimageandtheOSDmenuisnotbeingdisplayed,
- youcansetthemagnicationratiobypressingthejogdial.
- Youcanmovethedisplaylocationbymovingthejogdial(  orrotation).
- YoucansetthefollowingfunctionsusingtheCHbutton:
CH1:Selectzoommagnication;CH2:Switchbetweenzoompresets(Zoom1/Zoom2/Zoom3);CH3:Zoomoff
Zoom 2 [x4]

Operating the Video Display
8
Changing Image Quality Automatically According to Input Signal
Onthisvideodisplay,youcanautomaticallychangetheimagequalityaccordingtovideoresolutionormetadata.
Changing [Picture Mode] automatically ( 39)
1 Select [Channel Settings] [Select Channel].
•Selectthechannel.
2 Select [Channel Settings] [Picture Mode] [Type].
3 Select the Type using the jog dial.
Changing by individual video resolution (4K/2K)
Select[4K/2K].
Changing according to video resolution (4K/2K) or metadata (SDI)
Select[Automatic].
4 Select the Picture Mode.
Changing the image quality setting according to video metadata (HDMI) ( 30)
1 Select [Adjustment] [Picture Mode] [User 1] - [User 9].
2 Select [Adjustment] [Detail Settings] [HDMI Link] [Automatic Adjustment].
•Select[On].
•See[HDMILink]( 30)forthecongurablesettings.
Note
• Whenautomaticchangingofimagequalityaccordingtovideoresolution(4K/2K)orSDImetadataisset,
informationshowingwhichresolution(4K/2K,etc.)isselectedwillbedisplayedatthetoprightofthe
menuscreen.
Changing the screen display area
When4096x2160videosignalisinput,theleftandrightsidesoftheimagewillbecroppedtodisplayanareaof
3840x2160.Thecroppedsidescanthenbefurtheradjustedontheleftandright.
1 Select [Display Settings] [Screen Scaling].
•Select[NativeInputResolution]or[200%].
2 Press the jog dial ( ) while the OSD menu is closed.
•Shiftstotheleftorright.

Operating the Video Display
9
Export/Import
Youcanexport/import3DLUTandCDLparametersaswellasOSDmenusettings.
LUT Import ( 28)
1 Insert the USB memory stick containing the LUT file into the USB port of the video display.
2 Select [Adjustment] [Detail Settings] [LUT Import].
3 Select the LUT file to import.
•Inthe[Filename]eld,searchanddisplayalewithextension".clut"and".cube"intherootfolder.
4 Select the LUT No. to save the LUT.
5 Select [Execute].
•Whentheconrmationscreenappears,select[OK].Importstarts.
Note
• Importof[LUT]canalsobesetfrom[Adjustment] [CDL/UserLUT] [LUTImport].
• TheLUTle(.clutformat)isproprietarytoCanonVideoDisplay.RefertotheCanonwebsitefortheleformatandhowtocreate
theLUTle.
• Upto1000LUTimportlesarerecognized.
• YoucandeletetheimportedLUT,aswellasrenametheLUT( 28).
ThecongurationofLUTles(cubeformat)isshownbelow.
LUT filename
Type of characters that can be used One-bytealphabeticalcharactersandnumbersonly
No. of characters that can be used Upto64characters(includingtheextension)
Extension .cube
LUT file format
TITLE ASCII24characterscanbeused.
*DisplayedintheOSDmenuofthedisplayasaselectionitem.(Upto24characters)
LUT_3D_SIZE Specifyonefrom9/17/33/65.
Table Data SpecifyRed,GreenandBlue.
LUT_1D_SIZE
DOMAIN_MIN
DOMAIN_MAX
LUT_1D_INPUT_RANGE
LUT_3D_INPUT_RANGE
Unsupported.
• Forthelinefeedcode,use“CR(carriagereturn)”,“LF(linefeed)”,or“CR+LF”.
• Forthecharactercode,use“Shift-JIS”,“EUC-JP”,or“UTF-8(with/withoutBOM)”.

Operating the Video Display
10
Concept Drawing of Display Image Processing and LUT
Color Gamut/Gamma/
HDR Range, etc.
Range
conversion
Range
conversion
3D-LUT
Import
LUT Preset
Export/Import OSD Menu Settings ( 72)
1 Select [System Settings] [Export/Import].
2 Select [Export] or [Import].
Exporting
1Select[Target]from[USB],[User1]to[User3]or[LAN].
Theexportdestinationsareasfollows.
[USB]:USBmemory
[User1]to[User3]:Built-inmemoryofthemainunit
[LAN]:DisplayconnectedviaLAN
2Ifyouselected[USB],select[Filename].
• Thefactorydefaultis[dinfo_dpv****.dat](****:Numberoftheproductname).Youcanchangethenameof
theletobeexportedtotheUSBmemorywithin16one-bytecharactersincludingalphabeticalcharacters,
numbers,andsymbols.
Importing
1Select[Target]from[USB],[User1]to[User3].
Specifythedestinationtosavetheletobeimported.
2Select[Filename]when[USB]isselected.
3In[Settings],select[All]orMainMenuname.
3 Select [Execute].
•Whentheconrmationscreenappears,select[OK].Export/Importstarts.
Note
• Afterexportto[User1]to[User3],youcanselectthecongurationsatstartupfrom[User1]to[User3]in[PoweronSetting]in
[SystemSettings]( 72).

Operating the Video Display
11
Exporting/Importing CDL Parameters ( 26)
1 Select [Adjustment] [CDL/User LUT].
2 Select [CDL 1-8].
3 Select [Detail Settings] [CDL Export] or [CDL Import].
Exporting
1Select[CDLPreset].
2Selectaleformat".ccc"or".cdl".
Importing
1Select[Filename].
2Select[CDLPreset].
4 Select [Execute].
•Whentheconrmationscreenappears,select[OK].Export/Importstarts.
Note
• Theexportedleisautomaticallysavedunderthename"YYYYMMDDhhmmss_Presetname.ccc(cdl)".
• Upto1000CDLimportlesarerecognized.
Set Date/Time ( 70)
ThissectiondescribeshowtosetthevideodisplayDate/Time.ThevideodisplayDate/Timewillberesetifthepower
cordisnotconnectedforapproximately20days.
1 Select [System Settings] [Date/Time].
•AscreentoinputtheDate/Timeappears.
2 Set the Date/Time.
•Theselectionframemovesandnumberschangeasyouoperatethejogdial.Repeatuntilyoucompletesetting
theyear,month,date,hour,andminute.
3 Press the jog dial when you are finished.
•Theselectionframemovesto[OK].
4 Check the content and press the jog dial to confirm the settings.
Reference
• Whenselecting[Cancel]orpressingMENUbuttonbeforeselecting[OK],thesettingswillberesetandthepreviousscreenwillbe
displayed.

Operating the Video Display
12
Inputting Characters
Thissectiondescribeshowtoinputthecharacters.
1 When the character input screen is displayed, use the
jog dial ( ) to select the area you wish to input.
2 Select characters using the jog dial ( or rotation).
•Thefollowingcharacterscanbeselected:Press 
buttonstodisplaythemonebyone.
 Alphanumericcharacters:AtoZ,atoz,0to9
 Symbols:,.:;‘`-+/=%&!?#_|$^~@{}[]<>
()space
•Charactersthatcannotbeenteredareautomaticallyskipped.
3 Repeat steps 1 and 2 until the desired text has been input.
4 Press the jog dial when you are finished.
•Theselectionframemovesto[OK].
5 Check the content and press the jog dial to confirm the settings.
Reference
• Whenselecting[Cancel]orpressingMENUbuttonbeforeselecting[OK],thesettingswillberesetandthepreviousscreenwillbe
displayed.
• Toeraseacharacterintheselectionframe,presstheRESETbuttononthevideodisplay.

Operating the Video Display
13
Using the Function (F) Buttons
YoucanassignfunctionstotheFbuttonsonthevideodisplaytoexecutetheminstantly.Youcanassigndifferent
functionsonFbuttonsinthenormalandALTmodesrespectively.
1 Select [System Settings] [Function/Channel Button] [Function Button] or [Function Button
(ALT)].
•Thebuttonselectionscreenwillbedisplayed.
2 Select the button name and press the jog dial.
3 Select the function to assign.
•Refertothe"FunctiontoallowregistrationforthedisplayFbuttons( 74)"fortheavailablefunctions.
4 Press the jog dial.
•Thesettingisconrmed.
Thefollowingcontentisassignedtofunctionbuttonsonthevideodisplaybyfactorydefault.
Fbutton Normalmode ALTmode
F1 PictureMode CDL/UserLUT
F2 Brightness CDLSOP/SAT
F3 TC/ALM MultiInformationView
F4 WFM/VEC SingleInputDualView
F5 Histogram/FrameLuminance FalseColor
F6 ChromaDiagram/PixelValue RangeCheck
F7 ZoomPreset 2020OutsideofGamutView
F8 Volume CompareView
Reference
• HoldingtheFbuttondownwilldisplaythefunctionselectionscreen,andyoucansetthefunctionyouwishtoregister.
• YoucancheckthefunctionassignedtotheFbuttonsofthemainunit.
Openthe  [SystemSettings] [OSDSettings] [FunctionButtonGuide]menuandselect[On].Pressing/movingthe
jogdial(  ,orRotate)whileOSDisnotshowingwilldisplaythelistoffunctions.Selectingafunctionfromthelistand
pressing/moving( )thejogdialwilldisplaythedetailedsettingsscreen,orexecutethatfunction.
Pressing whilethelistoffunctionsisdisplayedswitchesbetweennormalmodeandALTmode.

Operating the Video Display
14
Using the Channel (CH) Button
Youcanassignchannels(varioussettingsrelatedtoinputsignal)totheCHbuttonsonthevideodisplayandswitch
channelsinstantly.
1 Select [System Settings] [Function/Channel Button] [Channel Button].
•Thebuttonselectionscreenwillbedisplayed.
2 Select the button name and press the jog dial.
3 Select the channel to assign.
•See[ChannelSettings]( 36)forthecongurablesettings.
4 Press the jog dial.
•Thesettingisconrmed.

Operating the Video Display
15
Thefollowingcontentisassignedtochannelbuttonsonthevideodisplayandtoeachchannelbyfactorydefault.
Item
Default Values by Channel
CH1 CH2 CH3 CH4 CH5 CH6
InputConguration 12-3G/
HD-SDI
HDMI 12-3G/
HD-SDI
12-3G/
HD-SDI
MultiView Notset
SelectInputSignal Automatic —Automatic
ImageDivision Automatic MultiView
(Quad)
Automatic
ScreenA~D —SDIInput
A~D
—
LinkOrder Automatic
Format Automatic
AudioInput Automatic SDIInputA Automatic
SwitchOut SelectOutput
Signal
Automatic(Thisisapaidupgradefunction.)
OutputSignal
Marker
Green(Sameasabove)
ChannelName (Blank)
PictureMode Type Normal
PictureMode ITU-RBT.709 User2
(2020HLG)
User1
(2020PQ)
User2
(2020HLG)
ITU-RBT.709
Resolution2K ITU-RBT.709
Payload UHD/PQ User1(PQ)
UHD/HLG User2(HLG)
UHD ITU-RBT.2020
709/PQ —
709/HLG —
709 ITU-RBT.709
VANC —
UNKNOWN —
Camera CINEMAEOS
SYSTEM
CINEMAEOSSYSTEM
ARRI User6
VARICAM User7
MarkerPreset Off
SingleInputDualView Off Off Automatic Automatic —Off
Separator Off
Note
• HoldingtheCHbuttondowndisplaysthechannellist,allowingtheusertoselectthedesiredchannel.

Operating the Video Display
16
Checking Signal Information and Status of the Main Unit
Thevideodisplayisequippedwithabannerdisplayfunction.
1 Press the jog dial when the OSD menu is closed.
•Thechannelname,signalinformation,andstatusofthemainunitwillbedisplayedinthebanner.Itwill
automaticallydisappearafter6seconds.
Note
• Youcanselecthowthebannerisdisplayed([Banner] 71).
• Youcanmonitortheinputsignalstatus.([SignalMonitoring] 59)
• Formoredetailedsignalinformation,pleaserefertothesectionon[SignalInformation]( 76).
• The[Detectingsync.]bannerwillcontinuetoappearuntiltheinputsignalissynchronized.
Operating the video display using an external device [GPI terminal]
YoucanoperatethevideodisplayusinganexternaldeviceconnectedtotheGPIterminalandexecutethefunctions
registeredineachpin.Remoteoperationispossibleonlywhenthevideodisplayisturnedon.
PinlayoutforGPIterminal PinNo. Signal Factorydefault
1 Pin1 CH1
2Pin2 CH2
3 Pin3 CH3
4 Pin4 TimeCode
5 Pin5 TallyGreen Atallyappearsatthe
topofthescreen.
6 Pin6 TallyRed
7 Pin7 PowerOn
8 Pin8(GND) —
1 Connect an external control device to the GPI terminal.
2 Select [System Settings] [GPI].
•Thepinselectionscreenwillbedisplayed.
3 Select a pin number and press the jog dial.
4 Select the function to assign.
•See[SystemSettings]( 70)intheOSDmenuforsettablefunctions.
5 Press the jog dial.
•Thesettingisconrmed.

Operating the Video Display
17
Operating the video display using an external device [LAN terminal]
ThevideodisplaysupportsTelevisionSystemsLtd.’s“TSLUMDProtocolVer.5.0”.Youcanoperatethevideodisplay
usinganexternaldeviceconnectedtotheLANterminalanddisplaycharactersandtallylightsonthescreen.Thereare
twotallylights,ontheleftandright.Upto16characterscanbedisplayed.
Tallydisplay(left) Characterdisplay Tallydisplay(right)
1 Connect an external control device to the LAN terminal.
2 Set [SCREEN] and [INDEX] to [0x0000] in the TSL Protocol settings.
3 Select [Network/IMD Settings] [In Monitor Display].
4 Select [Control] [TSL Ver. 5.00].
•Thiswillallowoperationfromanexternalcontroldevice,anddisplaycharactersandtallylights.
5 Select [Position] [Top] or [Bottom].
•Thissetsthepositionwherecharactersandtallylightswillbedisplayed.
Note
• When[MultiView(Dual)]or[MultiView(Quad)]isdisplayed,setthe[INDEX]settingtofrom[0x0001]to[0x0004].
• Theportnumberforthecontrollingisxedat"45000".
• With[InMonitorDisplay]youcanalsodisplayuser-selectedcharactersonthescreen.( 69)
• Unicodecharacterscanbeusedindisplayedtextstrings.However,somecharactersmaynotbedisplayedcorrectly.

Operating the Video Display
18
Use a web browser to remotely operate the video display
OperatethevideodisplayremotelyusingawebbrowseronacomputerterminalorotherdeviceconnectedtotheLAN
terminal.Fromthedeviceconnectedtothenetwork,youcanchangeimagequalitysettingsorswitchchannels.
Thisfunctionchecksoperationusingthefollowingwebbrowsers.
• Safari(Apple)
• GoogleChrome(Google)
※ *CorrectoperationcannotbeguaranteedonallsupportedOSorwebbrowsereditions.
CAUTION
• RemembertochangethedefaultsettingsforIDandPasswordwhenusingthisfunction.
Note
• Accessisonlypossiblefromasingleterminal.
• Openingmultiplepagesinmultipletabsonthewebbrowsercancauseittonotfunctionproperly.
• Operatingthevideodisplayitselfwhileitisbeingaccessedfromawebbrowsercancausethenetworkconnectiontobelost.
• Adelaymayoccurinvideodisplayorinthevarioussettingsdependingonthenetworkenvironmentandcommunication
conditions.
• TheIPaddresscanbecheckedinthe[SystemInformation]screen.
• TheoperationscreenonlydisplaysEnglish.
1 Connect external control devices via the network.
2 Select [Network/IMD Settings] [Web].
3 Select [Control] [On].
4 Select [User ID] and [Password] ( 68).
•[UserID]:EntertheuserID.Thisissetusingupto16alpha-numericalcharactersandsymbols.
 [Password]:Enterthepassword.Thisissetusingbetween8and16alpha-numericalcharactersandsymbols.
 Thefollowingcharacterscanbeentered.
 Alphanumericcharacters:AtoZ,atoz,0to9
 Symbols:_or-
5 Start up a web browser on the device connected to a network.
6 Enter the IP address of this video display in the address bar.
•Theremoteoperationscreenisdisplayedonthewebbrowser.
•Whenthebasicauthenticationscreenisdisplayed,entertheuserIDandpassword.
7 When operation ends, close the web browser.

Operating the Video Display
19
Operation screen
[Control] screen
AllowsthePictureMode,Channel,andvariousmarkerdisplaystobeset.
[Value/Name]*
Entercharactersornumbers.
[Get]:Acquiresinputdata.
[Set]:Appliesthedatatotheinputscreen.
[Zoom/PixelValue]
Setsthedisplaypositionfor[Zoom]orthepixel
positionfor[PixelValueCheck].
Click[Position/Function]todisplaythescreenwhere
youcanselecttheFbuttons.
* [Value]
• [Value]doesnotshowdecimalpoints.
• Dependingonthesettingitem,thevaluemaybedifferentfrom
thevaluedisplayedonthemenu.
[Setting] screen
YoucanimportLUT,exporttheerrorlogof[SignalMonitoring],andimportorexportthesettingsofthevideodisplay.
[ LUTImport(3D-LUT) ]
ImportsaLUT.
[SignalMonitoringLogExport]
Exportstheerrorlogof[SignalMonitoring].

Operating the Video Display
20
[lnformation] screen
Displaysthesettingsfor[Adjustment]and[ChannelSettings],andinformationfor[SignalInformation]and[System
Information].
[Link] screen
YoucandisplayalistofthedisplayconnectedviaLANtothisvideodisplay,set[DisplaySettingLink],andchange
thedisplaynames.