Captron 10 Series User manual

CANEO
Original Operating Instructions
series10 standard
CANEO
Original Operating Instructions
series10 standard
Connection plan
3-pin
OUT
(NPN/PNP NO/NC)
0V
+VDC
3
4
2
5
1
brown
black
blue
The product description will indicate the configuration.
4-pin
E1
OUT
(NPN/PNP NO/NC)
0V
+VDC
3
4
2
5
1
brown
white
black
blue
The product description will indicate the configuration.
Product description
5-pin
E1
E2
OUT
(NPN/PNP NO/NC)
0V
+VDC
3
4
2
5
1
brown
white
grey
black
blue
The product description will indicate the configuration.
Dimensional drawing
Metric and imperial measurements are used in drawings. Imperial
measurements are marked with [ ].
Technical specifications
Operating voltage DC 24 V (8.4…32 V)
Load current max. 200 mA
Output Adjustable PNP / NPN; NO / NC
Output pulse Adjustable
Reverse polarity protection Protection of all cables/lines
Short circuit protection Protected against short circuit and overload
Voltage drop Max. 5 V at 200 mA load current
Power consumption at 24 V Max. 40 mA
Operating temperature -30 °C (-22 °F)…+65 °C (149 °F)
Degree of protection IP Front IP69K
Degree of protection IK IK08
Communications interface IQ-link specification V1.1
Type of actuation Capacitive
Actuation force No actuation force required
Max. altitude 2000 m above sea level with "CSA" listing"
Relative air humidity Max. 95%, non-condensing
Drilling pattern
Safety
General safety
All work on electrical systems or operating equipment may only
be carried out by a specially qualified electrician according to the
applicable electrotechnical regulations.
The safety of the system in which the SENSORswitch is integrated
is the responsibility of the operator.
WARNING
Improper work on electrical systems!
Electric shock can result in death or life-threatening injuries.
4Before working on electrical systems, disconnect them from
their voltage supply and secure them against being switched
on again.
4Wear appropriate personal protective equipment (PPE).
Intended use
The SENSORswitch is intended for use in accordance with the
items listed here, the values from the “Technical specifications”
chapter and the product description.
■Only connect the product to a limited energy source as per IEC
61010 or an NEC class 2 power supply unit.
■Source current < 4 A at maximum operating voltage.
Reasonably foreseeable misuse
Any use other than as specified in the section Intended use or
extending beyond this is deemed to be improper.
The SENSORswitch is not suitable for:
■use in potentially explosive atmospheres.
■use as a safety component as per directive 2006/42/EC
The SENSORswitch is secured against rotation by the illustrated
hole.
Metric and imperial measurements are used in drawings. Imperial
measurements are marked with [ ].
Connection options
Plug M12, 3-pin
N/A
N/A
Plug M12, 4-pin
N/A
Plug M12, 5-pin
Foreword
This manual has been written for technicians/installers and
operators and should be kept for future reference. Read these
operating instructions carefully and make sure that you have
fully understood the contents before installing or working with the
SENSORswitches.
General description
The supplied SENSORswitch can have options that differ from
those shown in this manual. This does not affect the function.
The SENSORswitch is equipped with an RGB-LED to indicate
the operating conditions. The RGB-LED is controlled variably,
depending on the configuration.
A SENSORswitch
B Connection M12
C Lock nut
Assembly
Requirements: Mounting surface is level and clean.
► Disconnect the system from its voltage supply and secure it
against being switched on again.
► Set the desired position of the SENSORswitch and drill the hole
according to the drilling pattern.
► Insert SENSORswitch (A) into the prepared hole and screw the
lock nut (C) on.
► Position the SENSORswitch (A) and tighten the lock nuts with
max. 1.5 Nm.
► Connect SENSORswitch (A) electrically to terminal (B)
according to the connection plan.

Configure CANEO series10 with IO-Link
TIP
For information on configuring the
SENSORswitch, see our website
series10.captron.com or scan the QR
code.
Maintenance
Maintenance operations
Carry out the following maintenance operations at the specified
intervals.
Maintenance operation as needed annually
Clean the button surface X
Check cables for intactness and firm
fit
X
Check screw connections for
tightness
X
NOTICE
Solvents contained in cleaning agents can attack the
plastic of the button!
4Clean the surface of the button with a neutral cleaning agent
or a damp microfiber cloth.
Disassembly
► Disconnect the system from its voltage supply and secure it
against being switched on again.
► Disconnect the electrical connection and remove the lock nuts.
Disposal
Electrical and electronic components of various types must be
recycled according to their type.
Imprint
The operating instructions have been authored and published by
CAPTRON Electronic GmbH
Johann-G.-Gutenberg-Straße 7
82140 Olching – Germany
Tel.: [phone] - 44 88 - 160
[email protected]
www.captron.com
Copyright 2019
CANEO series10 1.1