FS S3410-24TS-P User manual

S3410-24TS-P/S5860-24XB-U
Quick Start Guide
24-PORT GIGABIT L2+/L3 POE
MANAGED SWITCHES
PoE
Status M1 M2 PWR1PWR2 PoE
1 2 3 4 5 6 7 8 910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P
PoE+
S5860-24XB-U
29 30 31 32
25 26 27 28
13 14 15 16 17 18 19 20 21 22 23 24
Yellow=OverLoad
5678910 11 12
On=Link Flashing=ACT PoE LED Mode:Green=GoodSupplyYellow=100M
1234
Green=10G/5G/2.5G/1G
MGMT
SYS PWR FAN PoE
PoE FUNC
CONSOLE
V1.1

Introduction
Accessories
S5860-24XB-U
S3410-24TS-P
Thank you for choosing S3410-24TS-P & S5860-24XB-U POE Switches. This guide is designed
to familiarize you with the layout of the switches and describes how to deploy the switches in your
network.
Grounding Cable x1
Power Cord x2
M4 Screw x8
Rubber Pad x4
Mounting Bracket x2
PoE
Status M1 M2 PWR1PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=OverLoad
CONSOLE Yellow=100M
NOTE: S3410-24TS-P & S5860-24XB-U POE switches have dust plugs delivered with
them. Keep the dust plugs properly and use them to protect idle optical ports.

S5860-24XB-U
S3410-24TS-P
Hardware Overview
Front Panel Ports
PoE
Status M1 M2 PWR1 PWR2 Po E
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
CONSOLE
MGMT
USB CONSOLE
USB RJ45
RJ45 SFP+ SFP28
RJ45/SFP Combo SFP+
Ports Description
RJ45
SFP+
RJ45/SFP Combo
USB
CONSOLE
10/100/1000BASE-T ports for Ethernet connection
One RJ45 port and one SFP slot, with one port active at a time
SFP+ ports for 1/10G connection
Reserved
An RJ45 console port for serial management
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M

S5860-24XB-U
S3410-24TS-P
Front Panel Buttons
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
PoE
Status M1 M2 PWR1 PWR2 Po E
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
PoE
Ports Description
RJ45
SFP28
SFP+
USB
CONSOLE
MGMT
100M/1G/2.5G/5G/10G ports for Ethernet connection
SFP+ ports for 1/10G connection
SFP28 ports for 10/25G connection
A USB management port for software and conguration backup and
oine software upgrade
An RJ45 console port for serial management
Button Description
PoE
PoE FUNC
Switch the display mode between PoE mode and switch mode.
Button Description
PoE
FUNC
Switch the display mode between PoE mode and switch mode.
NOTE: Press PoE Mode Switch-Over Button to switch the display mode between PoE mode
and switch mode.
The switch will restart after you press the FUNC button for more
than ve seconds and wait for another ten seconds.
An out-of-band Ethernet management port

M1SFANI-F
Status
M1SFANI-F
Status
M1SFANI-F
Status
FAN1 FA N2 FA N3 PWR1 PWR2
Input
Output
Input
Output
S5860-24XB-U
S3410-24TS-P
S3410-24TS-P
Back Panels
1
Power
2
Input
Module1 Module2
Output
Input
Output
Dual Power Supplies
Expansion Module Slot
Grounding Point Fan Slot
Grounding Point
Front Panel LEDs
PoE
Status M1 M2 PWR1 PWR2 Po E
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
RJ45
Status
M1
M2
PWR1
PoE
PWR2
SFPPoE (1-24)
SFP+
LEDs DescriptionStatus
Status
O Switch is not receiving power.
System is being initialized. Continuous blinking indicates
errors.
The switch is operational.
Temperature warning, check the working environment of
the switch immediately.
Switch is faulty.
Blinking Green
Solid Green
Solid Yellow
Solid Red
Dual Power Supplies

LEDs DescriptionStatus
M1/M2
O
Solid Green
Solid Green
Solid Yellow
PWR1/PWR2
PoE
RJ45
SFP
O
Solid Green
Solid Red The power module is in place but the AC power cord or
switch is abnormal.
The power supply is operational.
The power module is not in place.
O
Indicates the PoE state.
The port is not connected.
Solid Green The port is connected at 1000 Mbps.
Blinking Green The port is receiving or transmitting trac at 1000 Mbps.
Solid Yellow
O
Solid Green
Solid Yellow
The port is connected at 10/100 Mbps.
Blinking Yellow
Solid Yellow
Blinking Yellow
The port is receiving or transmitting trac at 10/100 Mbps.
O The port is not connected.
The port is not connected.
Solid Green The port is connected at 1000 Mbps.
Blinking Green
O
Solid Green
Blinking Green
The port is receiving or transmitting trac at 1000 Mbps.
The port is connected at 100 Mbps.
The port is receiving or transmitting trac at 100 Mbps.
Indicates the switching state.
There is no expansion module or the expansion module is
not correctly installed.
The expansion module is correctly installed.
PoE (1-24)
PoE is not enabled.
PoE is enabled. The port is operational.
The port has a PoE fault of overload.
SFP+
The port is connected.
The port is receiving or transmitting trac at 10Gbps.

S5860-24XB-U
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
LEDs DescriptionStatus
SYS
O
O
The system is powered o.
1.A system fault occurs.
2.The temperature reaches the upper limit.
Initialization is in progress.
The system works properly.
The locator takes eect. It is controlled by O&M personnel
remotely.
1.The temperature reaches the threshold value.
2.Dierent power modules are used together.
Blinking Green
Solid Green
Solid Green
Solid Green
Solid Green
Solid Yellow
O
Blinking Green
Solid Green
Solid Yellow
Blinking Yellow
Solid Yellow
Solid Blue
RJ45
PoE (1-24) SFP+
SFP28
MGMT
MGMT
SYS
PWR
PWR
FAN
FAN
PoE
PoE
Solid Red
Solid Red
Solid Red
Both power modules are NOT in the position.
The power module works properly.
1.A power fault occurs.
2.No AC power cable is plugged in.
3.The power model does not match.
The fan works properly.
1.A fan fault occurs.
2.The fan model does not match with the system.
3.Not all fans are in position.
Indicates the switching state.
Indicates the PoE state.
The MGMT port is NOT connected.
The MGMT port is connected at 1000Mbps.
The MGMT port is transmitting or receiving data at 1000Mbps.
The MGMT port is connected at 10/100Mbps.
The MGMT port is transmitting or receiving data at 10/100Mbps.

M1SFANI-F
Status
M1SFANI-F
Status
M1SFANI-F
Status
FAN1 FA N2 FA N3
PWR1 PWR2
Input
Output
Input
Output
Installation Requirements
Before you begin the installation, make sure that you have the following:
Category 5e or higher RJ-45 Ethernet cables, ber optical cables and console cable for
connecting network devices.
Phillips screwdriver.
Related electric cables and optical cables.
Standard-sized, 19" wide rack with a minimum of 1U height available.
O
O
O
O
Blinking Green
Blinking Green
Blinking Green
Solid Green
Solid Green
Solid Green
Solid Green
Yellow
Blinking Yellow
Back Panel LED
FAN Indicator
LEDs DescriptionStatus
RJ45
The RJ45 port is NOT connected.
The RJ45 port is connected at 1G/2.5G/5G/10G.
The RJ45 port is transmitting or receiving data at
1G/2.5G/5G/10G.
The RJ45 port is connected at 100Mbps.
PoE works properly.
PoE is o.
A PoE fault or overload occurs.
The RJ45 port is transmitting or receiving data at 100Mbps.
PoE ( 1-24)
Solid Yellow
SFP+
The SFP+ port is NOT connected.
The SFP+ port is connected at 10G/1G.
The SFP+ port is transmitting or receiving data at 10G/1G.
SFP28
The SFP28 port is NOT connected.
The SFP28 port isconnected at 25G/10G.
The SFP28 port is transmitting or receiving data at 25G/10G.
S5860-24XB-U

PoE
Status M1 M2 PWR1PWR2 PoE
1 2
2
3456 7 8 9 10 11 12
12 14 24
13 14 15 16 17 18 19 20 21 22 23 24
Green=1000M Yellow=10/100MOn=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=Over Load
Console
25F 26F 27F
RG-S2910-24GT2XS-UP-E
SFP+
PoE
Status M1 M2 PWR1 PWR2 PoE
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=OverLoad
CONSOLE
Site Environment:
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
PoE
Status M1 M2 PWR1 PWR2 PoE
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 26
23
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P
PoE+
Mounting the Switch
Do not operate it in an area that exceeds an ambient temperature of 50°C.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.

1. Secure the mounting brackets to the two sides of the S3410-24TS-P switch with eight M4 screws.
(S5860-24XB-U switch with six M4 screws by default, another 2 screws for redundant.)
Rack Mounting
RG-S2910-24GT2XS-UP-E
2. Attach the switch to the rack using four M6 screws and cage nuts.
SYS
24 25 26
23
SFP+
C3440-24T2F2SP PoE+

M1SFANI-F
FAN3
Wall Mounting
2. Use the expansion screws to securely attach the mounting brackets on the wall.
1. Secure the mounting brackets to the two sides of the switch with supplied screws.
26F 27F 28F
SFP+
PoE
Status M1 M2 PWR1PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+

Module1
Dual-power input:
The switch can be powered by one power module, or two power modules. When both two modules
are available, the switch is powered in load-balanced state.
Installing the Power Supply Module
2. Remove the blank panel and take the plane printed with power information as the top panel of
the power module. Hold the handle of the power module with one hand, and hold the end of the
power module with the other hand. Insert it into the chassis along the guide rail uprightly and
slowly until it clicks into place, and make sure that it is in good contact with the power slot.
1. Take a new power module out of the package and conrm the input mode and the input
parameters of the power module match the requirements.
NOTE: When the switch is powered by the dual-power modules, if the system working
power is greater than the capacity of single power module, power redundancy cannot
work.
100-240v-;50/60Hz;7-3.5A
Input
Output
Status
M1SFANI-F
Status
M1SFANI-F
Status
PWR1 PWR2
Input
Output

Grounding the Switch
1
Power
2
Input
Module2
Output
Input
Output
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers and
screws.
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
Module1

Connecting the RJ45 Ports
1. Connect an Ethernet cable to the RJ45 port of IP cameras, IP telephone, Access Points (AP), or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
Connecting the Power
1
Power
2
Input
Module2
Output
Input
Output
PoE
Status M1 M2 PWR1 PWR2 PoE
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25
23
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
WARNING: Do not install power cable while the power is on.

1. Plug the compatible SFP/SFP+ transceiver into the SFP/SFP+ port.
2. Connect a ber optic cable to the ber transceiver. Then connect the other end of the cable to
another ber device.
WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical bers without eye protection.
Connecting the SFP/SFP+ Ports
PWR2 PoE
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 26
23
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoE LED:Green=Good Supply Yellow=OverLoad
SFP+
S3410-24TS-P PoE+

Connecting the Console Port
25
13 14 15 16 17 18 19 20 21 22 23 24
Yellow=Over Load
5678910 11 12
On=Link Flashing=ACT PoE LED Mode:Green=Good SupplyYellow=100M
1234
Green=10G/5G/2.5G/1G
MGMT
SYS PWR FAN PoE
PoE FUNC
CONSOLE
PoE
Status M1 M2 PWR1PWR2 Po E
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
23
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=Over Load
CONSOLE
C3440-24T2F2SP
1. Insert the RJ45 connector into the RJ45 console port on the front of the switch.
2. Connect the DB9 female connector of the console cable to the serial port on the computer.
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the MGMT port on the front of the switch.
Connecting the MGMT Port

PoE
Status M1 M2 PWR1 PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
PoE
Status M1 M2 PWR1 PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
PoE
Status M1 M2 PWR1 PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
PoE
Status M1 M2 PWR1 PWR2 PoE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
24 25 2623
Green=1000M Yellow=10/100M On=Link Flashing=ACT PoELED:Green=Good Supply Yellow=OverLoad
CONSOLE
SFP+
S3410-24TS-P PoE+
Stacking the S3410-24TS-P Switch
The S3410-24TS-P switch supports stacking up to 4 switches between the same models together.
The switch can be physically stacked using optical ber cables connected to SFP+ transceivers or
10G Direct Attach Cables (DAC). The two SFP+ ports on the switch can be used for physical stacking.
Stacking the S5860-24XB-U Switch
Stacking the Switches
The S5860-24XB-U switch supports stacking up to 2 switches between the same models together.
The switch can be physically stacked using optical ber cables connected to SFP+/SFP28 transceivers
or 10G/25G Direct Attach Cables (DAC). Any two SFP+/SFP28 ports on the switch can be used for
physical stacking. The copper ports can also be used for physical stacking.
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
S5860-24XB-U
29 30 31 32
28
25 26
SFP+

Conguring the Switch
Conguring the Switch Using the Web-based Interface
Step 1: Connect the computer to any Ethernet port of the S3410-24TS-P switch using the network
cable, and connect the computer to the Management port of the S5860-24XB-U switch using
the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. ("x" is any number from 2 to 254.). Set the
subnet mask of the computer to 255.255.255.0.
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses:
Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password,
admin/admin.
Step 4: Click Login to display the web-based conguration page.
IE 8/9/10/11, Google Chrome, Firefox are supported
Login
admin
*****

Conguring the Switch Using the Console Port
Step 1: Connect a computer to the switch's console port using the console cable.
Step 2: Start the terminal simulation software such as HyperTerminal on the computer.
Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1 stop
bit and no ow control.
Step 4: After setting the parameters, click Connect to enter.
Troubleshooting
Serial port console has no output or outputs illegible characters
1. Change the serial port opened by the conguration software to be the one connected to the switch.
2. Check that the parameter conguration of the serial port matches that specied in the instructions.
10G Port is not Working
In the case of compatible cables and transceivers, the port cannot be up, please try to modify the
port mode to adapt or force the port speed to 1G/10G.
Connecting the Switch Remotely Unsuccessfully
1. Test network connectivity through ping.
2. If the network is reachable, try restarting the switch.
3. Check if the corresponding service is enabled.
x
Quick Connect
Protocol:
The port may be manually entered or selected from the list.
Serial
Flow Control
DTR/DSR
RTS/CTS
XON/XOFF
Save sessionShow quick connect on startup
Open in a tab
Connect
Cancel
COM3
9600
8
None
1
Port:
Baud rate:
Data bits:
Parity:
Stop bits:
Name of pipe:

Product Warranty
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html
5
1. Replace the twisted pair cable.
2. Check that the port conguration has the common working mode with the connected switch.
The Port is not Working, the LED Indicator is O
1. Ensure the switch ports are in the no shutdown state.
2. Check if the switch can read the DDM information.
3. Check if the port speed setting is correct.
4. Try looping the switch cable.
RJ45 port is not in connectivity or it is erroneous in receiving/transmitting
frames
Support and Other Resources
Download
Help Center
Contact Us
https://www.fs.com/download.html
https://www.fs.com/service/help_center.html
https://www.fs.com/contact_us.html
our workmanship, we will oer a free return within 30 Days from the day you receive your goods.
This excludes any custom made items or tailored solutions.
Warranty: S3410-24TS-P & S5860-24XB-U switches enjoy 5 years limited warranty
against defect in materials or workmanship. For more details about warranty, please
check at
https://www.fs.com/policies/warranty.html
Copyright © 2020 FS.COM All Rights Reserved.
Q.C. PASSED