Car-Interface.com C1-MFD1 User manual

Product description
Article C1-MFD1
Function This interface enables the connection of an external video
device (e.g. DVD Player, DVB-T Tuner) to display-based Audi
and VW navigation systems.
Options to adjust contrast, brightness and/or colour saturation
are provided. The interface allows controlling the connected
video source(s) using the navigation system controls.
The following navigation systems are supported:
Audi Navi Plus RNS-D and VW MFD1
Supported video systems: PAL / NTSC
● Pink
ACC +12V (max. 500mA)
● Green
+12V rear-view camera (max. 1A)
●Grey
Ground rear-view camera
●White
Switch to rear-view camera (+12V = switching on)

Product description
Article C1C-VW01
Function Harness for Multimedia Interface “C1C-M01”
For use in conjunction with the following systems
VW and SKODA with MFD1
AUDI with Navi Plus
Pin assignment of harness C1C-VW01
Colour/Connector
Assignment
10pin connector
Rear side of navigation unit
● Red
+12V permanent
● Black
Ground
●Yellow
CAN-High
●Blue
CAN-Low
●Green
VIDEO ON +12V (only for navigation version A or B)
3pin AMP connector
IR-port of AV-source
● Cinch connector red
AUDIO-Input (right)
● Cinch connector black
AUDIO-Input (left)
Installation of harness with C1C-M01
Instruction for VW, Skoda with MFD1 and AUDI with Navi Plus
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Place of installation is behind the head-unit.
1. Remove the navigation unit from the centre console.
2. Remove all connectors from the navigation unit.
(MFD I)

3. Connect 10pin connector of harness C1C-VW01 to the
female 10pin connector of the navigation unit.
4. Connect the corresponding control cable to the jack socket.
Additionally, the available Y-adapter (sold separately) may be
used to enable the connection of the IR-remote receiver of a
video source parallel to the interface itself. Connect this adapter
between the jack socket of the cable kit and the corresponding
control cable. A Video / Audio Cinch cable (sold separately) is
needed to connect the video source to the three Cinch sockets
of the interface.
5. Connect the blue cable from the harness to pin 26 of the 26pin
connector of the navigation unit. Connect the yellow cable to pin
13 of the 26pin connector. Connect the black cable to ground
(power connector pin 8) and the red cable to 12V battery (power
connector pin 7).
The green cable is for circuit-entering of Audi Navi Plus from year
1999 and MFD1 version A or B. Connect it to +12V (Power
connector pin 4).
6. Reconnect all original connectors to the navigation unit and re-
attach it to the center console.

Function and controls
Activation
Push the AUDIO button of VW as the case may be the
RADIO/CD/TV of Audi to activate the TV/AV input.
Device assignment
Longpress the AS button (VW) as the case may be the MODE button (Audi) to assign device
control. Turn right knob until the device-related IR-code as described in device control table
(appendix A) is reached. Push right knob to confirm the assignment.
Note: The vehicle has no MFD display in the instrument panel. You have to count the
notches when turning the knob (to the right +1, to the left -1). At the same time, remember
that the starting point is channel RC01 (the first notch to the right is then already RC02).

Controls:
The video source is controlled using various buttons of the navigation. Pushing the upper
right knob for a prolonged time switches between device controls. For a detailed button
assignment see chart below.
Button assignments for MFD I
Button assignment table cLOGiC VW MFD1
Head-Unit
button
usbLiNK
DVB-T tuner
DVD-player
DVD-ahnger
iPod®-control
Analog-tuner
1
POWER
PLAY/PAUSE
PLAY
PLAY
PLAY/PAUSE
SCAN
2
VOL+
EPG
PBC
PBC
SHUFFLE
FM
3
VOL-
INFO
TITLE
TITLE
REPEAT
DISPLAY
4
←
←
←
←
←
CH -
5
→
→
→
→
→
CH +
6
SETUP
MENU
SETUP
SETUP
BULB
ADJUST
7
TRACK -
CH -
TRACK -
TRACK -
TRACK -
CH -
8
TRACK +
CH +
TRACK +
TRACK +
TRACK +
CH +
9
MEDIA
AV
AV
AV
EJECT
MODE
9 (3Sek.)
RC CODE
RC CODE
RC CODE
RC CODE
RC CODE
RC CODE
10
ZOOM
SCAN
ZOOM
DISC
MODE
10 (3Sek.)
POWER
POWER
POWER
POWER
POWER
POWER
11
OK/PLAY
OK
ENTER
ENTER
ENTER
MODE
11 (3Sek.)
SWITCH
USB/AV
SWITCH
USB/DVB-T
SWITCH
USB/DVD
SWITCH
USB/DVD
SWITCH
USB/iPod
SWITCH USB/TV
12
↑
↑
↑
↑
↑
VOL +
13
↓
↓
↓
↓
↓
VOL -
14
EXIT
EXIT
STOP
STOP
PLAY
MUTE
14 (3Sek.)
SETTINGS
SETTINGS
SETTINGS
SETTINGS
SETTINGS
SETTINGS

Button assignments for AUDI Navi Plus
Button assignment table cLOGiC Audi Navi Plus
Head-Unit
button
usbLiNK
DVB-T tuner
DVD-player
DVD-
changer
iPod®-control
Analog-tuner
1
TRACK -
CH -
TRACK -
TRACK -
TRACK -
CH -
2
TRACK +
CH +
TRACK +
TRACK +
TRACK +
CH +
3
←
←
←
←
←
CH -
4
→
→
→
→
→
CH +
5
MEDIA
AV
AV
AV
AV
MODE
5 (3Sek.)
POWER
POWER
POWER
POWER
POWER
POWER
6
EXIT
EXIT
STOP
STOP
ESC
MUTE
6 (3Sek.)
SETTINGS
SETTINGS
SETTINGS
SETTINGS
SETTINGS
SETTINGS
7
OK/PLAY
OK
ENTER
ENTER
ENTER
MODE
7 (3Sek.)
SWITCH
USB/AV
SWITCH
USB/DVB-T
SWITCH
USB/DVD
SWITCH
USB/DVD
SWITCH
USB/iPod
SWITCH USB/TV
8
↑
↑
↑
↑
↑
VOL +
9
↓
↓
↓
↓
↓
VOL -
10
SETUP
MENU
SETUP
SETUP
LIGHT
ADJUST
10 (3Sek.)
RC-CODE
RC-CODE
RC-CODE
RC-CODE
RC-CODE
RC-CODE
11
VOL-
EPG
PBC
PBC
SHUFFLE
FM
11 (3Sek.)
MEDIA
LANG
SUB
SUB
MUTE
12
VOL+
SCAN
PLAY
PLAY
PLAY/PAUSE
SCAN
12 (3Sek.)
OSD
INFO
TITLE
DISC
REPEAT
DISPLAY