Car-Interface CI-AUX-110 User manual

Version 07.12.2015
AUX-In Interface
CI-AUX-110
Compatible with:
Audi MMI3G basic/high
BMW Professional radio, Business and
Professional navigation systems (CCC, CIC)
with iDrive,
Mercedes Benz Audio5, Audio20, APS50,
Comand APS NTG1/NTG2,
Porsche PCM 2.0 and 2.1

Version 07.12.2015 CI-AUX-110
Page1
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
2. Installation
2.1. Selection of vehicle (blue wire)
2.2. Installation example Audi MMI 2G
2.3. Installation example Porsche Cayenne PCM2.1
2.4. Exception: Vehicles without optical lead components BMW
2.5. Exception: Vehicles without optical lead components Mercedes/Porsche
3. Operation
4. Specifications
Information
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.

Version 07.12.2015 CI-AUX-110
Page2
Requirements
Navigation/Radio Audi MMI 3G basic/high (not A1!)
BMW Professional radio, Business and Professional navigation
systems (CCC, CIC) with iDrive
Mercedes Audio5, Audio20, APS50, Comand APS NTG1/NTG2
Porsche PCM2.0, PCM2.1
Limitations
Factory CD-changer A existing factory CD-changers must be removed.
BMW without If factory CD-changer has never been installed, the head-unit
MOST®-components needs to be coded to CD-changer by diagnosis computer or
OBD-xxx-CD-xx activator.
Mercedes/Porsche without MOST®-ring needs to be activated by diagnosis computer
MOST®-components
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
AUX-110 HW_____ SW_____
Take down the SW-version and HW-version of the interface boxes,
and store this manual for support purposes.

Version 07.12.2015 CI-AUX-110
Page3
2. Installation
Switch off ignition and disconnect the vehicle’s battery!
The interface needs a permanent 12V source. If power source is not taken directly from
the battery, the connection has to be checked for being start-up proven and permanent.
Installation on BMW or Mercedes analogue to installation examples of Audi and Porsche.
2.1. Vehicle selection (blue wire)
For installation on Audi, Mercedes or Porsche, blue wire is not connected and needs to be
isolated.
For installation on BMW connect blue wire constantly to ground (GND).
2.2. Installation example Audi MMI 3G
Remove MOST®-connector and integrate Interface
according to schema. Obey arrows one the MOST®
-connectors as well as the order of components.
Connect black wire to ground and red wire to
permanent +12V. Isolate blue wire.
2.3. Installation example Porsche Cayenne PCM 2.1
Black wire Red wire
GND +12V permanent

Version 07.12.2015 CI-AUX-110
Page4
Remove plastic cover.
Remove 4 torx screws and pull out head-unit from the
dash-board.
Remove MOST®-connector from the rear of the
factory CD changer and integrate Interface according
to schema. Obey arrows one the MOST®-connectors.
Connect black wire to ground and red wire to
permanent +12V. Isolate blue wire.
2.4. Exception: Vehicles without optical lead components BMW
Vehicles without MOST®-components, which means without factory CDC, without factory
phone or other MOST®-components have optical leads at the navigation computer, but it
can be possible that the optical ring is not closed at the diagnostic connector in the glove
compartment. In this case a connector bridge for optical wires is necessary.
2.5. Exception: Vehicles without optical lead components Mercedes/Porsche
The MOST®-ring (optical) needs to be opened/activated by diagnosis computer.
3. Operation

Version 07.12.2015 CI-AUX-110
Page5
The AUX-110 emulates a factory CD-changer and is recognized as such by the head-unit. The
AUX-input is activated by playing CD1 on the head-unit.
4. Specifications
Operation voltage 10.5 –14.8V
Stand-by power drain <1mA
Operation power drain 120mA
Power consumption 1.8W
Temperature range -30°C bis +80°C
Weight 95g
Measurements (box only) B x H x T 106 x 30 x 71 mm
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.