Car-Systems MBUX NTG 7 User manual
MBUX NTG7 Video in Motion Module Installation manual
2023
www.carsystems.com.ua
MBUX NTG7 Video in Motion Module
Installation manual
Revision 0.1 06/2023
MBUX NTG7 Video in Motion Module Installation manual
2 Content Rev. 0.1 06/2023 www.carsystems.com.ua
WARNING
Qualified personnel with experience in automotive electronics, who are conversant with safety
measures related to the use of electrical equipment, and who are conversant with the contents of
this manual are allowed to work with the Module.
BEFORE INSTALLING THE MODULE, IT IS NECESSARY:
1. LET THE CAR FALL ASLEEP;
2. PULL OUT THE IGNITION KEY FROM THE IGNITION;
3. PUT THE IGNITION KEY AWAY FROM THE CAR;
4. DISCONNECT THE POWER TERMINALS FROM THE CAR
BATTERY (FOR YOUR SAFETY DURING INSTALLATION).
Any access to the internal part of the Module, inside the case, will lead to the loss of the
factory warranty. If your Module needs repair,please contact us and we will assist you
(Our support contacts ).
The manufacturer is not responsible for damaged equipment during the installation of the
Module, or during the operation of the Module, as well as material, moral damage, or loss of
health.
MBUX NTG7 Video in Motion Module Installation manual
www.carsystems.com.ua Rev. 0.1 06/2023 Content 3
Content
Warning.…………………………………………………………………....…..……………... 2
1.
Preface.……...…………………………………………………………………………....
4
2. Delivery kit and appearance …………………………….…………………………...….. 5
3.
Location of the elements for Module installation.………………………………………..
6
4. Block diagram ……………………………………..……………………………............. 7
5.
Installation process..……..……………………………………....……………………….
8
5.1. Dismantling of interior elements to install the Module……...………………………. 8
5.2.
Installing the Module…...……….……………………………………………………
11
5.3. Module location.…………………………………………….……..………………… 18
6.
Our contacts.……………………………………………………………………………...
19
MBUX NTG7 Video in Motion Module Installation manual
4 Content Rev. 0.1 06/2023 www.carsystems.com.ua
1. Preface
This manual contains a Module installation guide and will help you to install the
MBUX NTG7 Video in Motion Module (hereinafter Module).
1.1. Audience
The document describes Module installation procedure and is intended for customers,
partners, and employees of CarSystems.
This document provides instructions and graphics needed for the install Module.
1.2. Pre-installation skills
This document assumes that you already familiar with automotive electronics, have
knowledge and experience in this field. Advanced car diagnostic skills are welcomed.
MBUX NTG7 Video in Motion Module Installation manual
8 Content Rev. 0.1 06/2023 www.carsystems.com.ua
5. Installation process
5.1. Dismantling of interior elements to install the Module
Picture 4
Detach driver's seat and tilt toward rear. Loosen the edge guard in the area of the cover and
remove the cover. Remove front door sill molding.
To remove door sill molding, you need to put the hand to the gray strip on the larger part and
bend it towards you until a short click is heard.
Unclip the cover from under the glove box and bend the floor covering (Picture 5).
MBUX NTG7 Video in Motion Module Installation manual
10 Content Rev. 0.1 06/2023 www.carsystems.com.ua
5.2. Installing the Module
5.2.1. Connecting the Module to the EZS ignition switch module
Picture 7
Unclip EZS ignition switch module: press on the highlighted part (Picture 7) and pull down
EZS ignition switch module.
MBUX NTG7 Video in Motion Module Installation manual
www.carsystems.com.ua Rev. 0.1 06/2023 Content 11
Picture 8 EZS ignition switch module connectors locations
Picture 9
Remove 6 port ETHERNET connector frame from COM 3 socket. Its location is
highlighted in (Picture 8) under number 3 and (Picture 9).
MBUX NTG7 Video in Motion Module Installation manual
14 Content Rev. 0.1 06/2023 www.carsystems.com.ua
•Remove Head Unit ETHERNET cable from 6 port ETHERNET connector frame:
-Remove the locking bar: use tweezers to bend the plastic on the plugs as shown in
(Picture 11 №1);
-Remove Head Unit ETHERNET cable from position slot 5 in 6 port ETHERNET
connector frame: use tweezers to bend the plastic blocker as shown in (Picture 11 №2).
Picture 12
Connect ETHERNET cable from the Module to 6 port ETHERNET connector frame to
position slot 5 (Picture 12).
MBUX NTG7 Video in Motion Module Installation manual
www.carsystems.com.ua Rev. 0.1 06/2023 Content 15
Picture 13
•Сonnect Head Unit ETHERNET cableto ETHERNET socket from the Module:
-Fix Head Unit ETHERNET cable in ETHERNET connector frame;
-Connect ETHERNET connector frame with Head unit ETHERNET cable to
ETHERNET socket from the Module;
-Install EZS ignition switch module in its location ( Picture 2 ).
MBUX NTG7 Video in Motion Module Installation manual
16 Content Rev. 0.1 06/2023 www.carsystems.com.ua
5.2.2. Connecting power wire 12 volts from Module to fuse box F152/4
Cut off the plastic tie and unscrew the screw of the power terminal
Picture 14
Remove the fuse box F152/4.
Tool: Simple loop is small.
1/4 in. (4-14 mm.) socket head.
MBUX NTG7 Video in Motion Module Installation manual
www.carsystems.com.ua Rev. 0.1 06/2023 Content 17
Picture 15Front side and back side fuse box F152/4
Install 2 Amps FUSE (from delivery kit) in F321 (default) and plug power wire 12 volts
from the Module in A2_4 (default).
*If default locations are occupied:
Use 2..5 Amps FUSE and locations F328 (with A3_3 ) or F335 (with A3_10).
Picture 16 Power wire 12 volts from the Module install
Install the fuse box F152/4 back to its location ( Picture 14 ) and tighten the screw.
MBUX NTG7 Video in Motion Module Installation manual
www.carsystems.com.ua Rev. 0.1 06/2023 Content 19
6. Our contacts
Email: support@carsystems.com.ua
Phone: +38 (096) 809-00-11
Skype: carsystems.support
Viber: +38 (096) 809-00-11
Telegram: @CarSystems_Support
We provide technical support during working hours: From Monday to Friday (except
public holidays). From 10:00 to 19:00 (UTC +2:00).
Due to the increase in the number of unsolicited e-mails, we have strengthened our
protection against spam. If your letter has not been delivered, please contact us via Skype or via
the request form on our website https://carsystems.com.ua/contacts/.
All rights for images belong to CarSystems (www.carsystems.com.ua).
Table of contents
