CARBONE MMX-607R User manual

Before using product, please read this
instructions carefully and safe-keeping.
Don't use the overladen Power socket,power wire and broken
power wire plugs;
Don't try to open the product,If happen abnormal phenomenon,
Please contact with the relevant Technical department;
If lightning and thunder, please do not touch the power supply
cable.
BASIC PARAMETERS 1
Model
Dimensions
Upply Voltage
Total Power
Coverage Area
278*83mm
DC12V
6W
60m²
INSPECTION EQUIPMENT
+
Aroma diffuser Power Adaptor
+
Written materials
Pr od uc t Ma nu al
Checking and make sure the packaging is complete when you first open it,
(it includes machine, fragrance bottle, power cord, manual) if any problem
please contact with us soon.
2
METHOD OF USE
1.Open the packaging and take out the equipment
Power Adaptor
Connect well with the bayonet
of the upper part
Power Interface
Bottom part of device
Fragrance exit
Connect well with the
rabbet of the bottom part
Upper part of device
Empty oil bottle
3
METHOD OF USE
Figure 1 Figure 2
2. Open fragrance bottle cap, then
keep Vertical-horizontal rotate it
install into the upper part of the device
where thread on connection. (Note:
Pay more attention on it when install
fragrance bottle, to prevent fragrance
overflow)
Put the tube inside
the fragrance bottle
counterclockwise into the
upper part of the equipment
3.Take the upper part of the
device (after install fragrance
bottle) and aligned well with
the bottom part's bayonet
and rabbet , then Forced
under pressure, and then
clockwise clamping.
Fixed fragrance bottle
Figure 3
Put into the
bottom part
of device
Figure 4
The rabbet aligned
bayonet
After press down then Clockwise rotate
the upper part snaps into bottom.
Figure 5
4
METHOD OF USE
4.Take out the power adaptor,
one side connect with the
equipment, other side connect
with power.
5
METHOD OF USE
5.Connecting the power,
when the indicator turns
green, equipment starts
to work.
Power
Interface
Power plug
PRODUCT MANUAL
AROMA DIFFUSER

6
Using Steps
1 Add Aroma Oil:
Holding the upper and lower parts of machine with your hands, rotating counterclockwise
to separate the bottle and machine, remove the bottle and put into suitable amount oil in it ,
then put the bottle to machine ,tighten the upper and lower parts of the diffuser according
to indicated position.
2 Connect power adapter:
Connect the power adapter to the lower power access point [DC POWER IN],put the plug
into the power outlet.
3 Control Instructions:
There are 3 colors of LED light:
Blue light is power on indicator
Green light is working indicator
Red light,press any button of remote control,green light turns into red color.
7
Remote Control Setting
press this key to turn on & turn off the machine
AROMA
(AROMA): In working condition, press this key to come back to the
initial mode---Maximum spray volume, working all the time。
This button is also worked as RESET
DENSITY
+
DENSITY
-
(DENSITY +): In working condition,press this key, every time
increases 10% aroma density, 8 levels in total---press ten times to
reach the maximum density.
(DENSITY -): In working condition,press this key, every time
decreases 10% aroma density , 8 levels in total---press ten times to
reach the minimum density.
30/30s (30/30s): In working condition,press this key to work for 30 seconds
and pause 30 seconds.
8
Remote Control Setting
30/60s (30/60s): In power-on condition,press this key to work for 30 seconds
and pause 60 seconds.
30/120s (30/120s): In power-on condition,press this key to work for 30
seconds and pause 120 seconds.
4 Remote control working time
1h (1h): In power-on condition,press this key to work for 1 hour
continuously per day, other time is no working.
4h (4h): In power-on condition,press this key to work for 4 hours
continuously per day, other time is no working.
8h (8h): In power-on condition,press this key to work for 8 hours
continuously per day, other time is no working.
10
EQUIPMENT CLEANING
Ev ery ti me when make a re plac ement of frag rance or
af ter some time opera tions, the fragra nces smoke come
ou t from the nebulize r are le ss than befor e, we ne ed to
do a c leaning and maint enance.
Cleaning steps:
Ca refully ope n the
eq uipment and take
ou t the fragran ce
bo ttle, which t he
fr agrances have bee n
ru n out.
11
EQUIPMENT CLEANING
Pu t som e alcohol i nto the bottle a gain, then ins tall it on
th e equ ipment, a nd then turn on th e equ ipment le t it wo rk
fo r 5-1 0 minutes .
Pu t som e alcohol i n it
Al cohol
EQUIPMENT CLEANING
12
After clea n ing, turn off th e eq uipment .
Tak e ou t th e fr a grance bot t le ag ain, and make a replace m ent of
fragra n ce that you like, fina l ly in stall on the machi n e c areful l y.
13
COMMON FAULTS AND EXCLUSION
Che c k Th e Power Is On Or Off , Pump Da m a g ed
Th e Device Is Til t e d , Spray He ad Is Da maged
Bo t t l e Is Lo o s e
Pu m p Is Lo o s e
FAU LTS
Do N o t Spray
Lit t l e Smoke Ou t
Sp r a y Liquid
Pe r f u m e spill
Ab n o r m a l Sound
EX CLUSION
At o m i z i n g head i s blocked, Cl e aning eq u i p m e nt
to confirm,Pump is agin g
After fragranc e bottle installed ( with f ragranc e in it ), pleas e keep
the mac hine ve rtical, don’t ti lt or put down, to avoid the fra gr ance
overf lo w, whi ch will contaminat ed equipm en t circu it , affe ct ing the
norma l use and unnecess ar y waste .
9
NOTE