CareCo X8 High Active User manual

WC01054 - X8 High Active Manual Chair
Thank you for purchasing the X8 High Active Chair from CareCo, we hope you are pleased with
your purchase.
The wheelchair is intended for both indoor and outdoor use. The weight capacity is 125 KGS.
Take care of all safety tips before use.
Footrest and foot plate.Front fork
Quick release button
Seat and back upholstery
Rear wheel
Brake.
Handle
Castor.




a. Take the wheelchair out of the
shipping box.
b. Check the quick release axle on the
rear wheel to ensure it is locked
securely in the rear axle.
d. Mount the footrests and side panels
on the wheelchair.
e. Put the padded seat into the seat
upholstery, ensure that the Velcro is
fastened and no risk of sliding from
the seat upholstery.
c. Unfasten the buckles. Press the seat
down to unfold the wheelchair.
PREPARATION BEFORE USE

a. Move the wheelchair and get it at 45 degree angle toward the user’s chair,
make sure that the brakes are not entangled together.
b. Lock the user’s wheel brakes.
c. Lock the other wheelchair brakes securely. Fold up the plastic footplates
if necessary.
d. Put your feet on the ground and move forward on the wheelchair.
e. Get into the other wheelchair. The concept of this movement is that you can do this
independently.
Note: you can practice this movement with the assistance of an attendant.
f. Lower down the footplates and put your feet on them. Then release the
wheel brakes.
The user’s feet can be placed on the footplates.
The angle and height can be adjusted by a professional for maximum function and comfort.
Dismount and mount the standard footrest
a. Pull the release handle on the footrest backward.
b. Turn the footrest outward at 90 degrees and lift it up to take out the footrest from the
sockets on the wheelchair.
c. Put the footrest at 90 degrees from outside of the wheelchair.
d. Turn the footrest in and lock the release handle while put the footrest head
into the legrest sockets.

FOOTPLATE
GETTING IN AND OUT OF THE WHEELCHAIR
The method of getting in and out of the wheelchair described as following:
The wheelchair is designed for a disabled person who can get in and out of the wheelchair
independently. Use the following method to get into the wheelchair. If assistance is needed
during the process, use the following method with the assistance of an attendant.

ADJUSTMENT AND FOOTPLATE HEIGHT
FASTEN AND LOOSEN THE HEEL LOOP
DISMOUNTING THE HEEL LOOP
SEAT AND BACK UPHOLSTERY
MOUNTING AND DISMOUNTING THE PADDED
SIDE PANEL SAFETY TIPS
FLIP UP AND REMOVE SIDE PANEL
Footplate height can be adjusted by a professional.
The heel loop provides extra support to the feet of user. It can be dismounted for cleaning.
Fasten the heel loop
a. Put the heel loop onto the jointing point of the footrest and the footplate struts.
b. Fasten the Velcro.
a. Unfasten the Velcro.
b. Take the heel loop out of the footrest.
The seat and back upholstery is used for pressure distribution of the user during use.
Once damaged or ruptured, please replace it immediately.
Keep it away from Fire and other ammable objects.
Padded seat is used to provide maximum comfort.
It can be taken out of seat upholstery for cleaning.
After cleaning, it can be put back on the seat upholstery and fasten the Velcro.
There is potential danger of pinched ngers or any part of the body.
Don’t put your ngers or any part of your body between side panel and the
wheelchair frame.
The side panels are used to prevent the user’s clothes from getting dirty. It can provide
additional support to user’s arms as well.
a. Release the lock lever on the side panel.
b. Flip up the side panel at 90 degrees.
c. Lift the side panel upwards to the seat back and take out the side panel from
it’s socket.

ADJUSTMENT OF ARMREST HEIGHT
MOUNT/LOCK THE SIDE PANEL
MOUNT AND DISMOUNT THE SIDE PANELS
There are 4 different height positions of the armrest.
a. Loosen the nuts on the armrest.
b. Adjust the armrest to the desired height.
c. Tighten the nut again to make it locked securely in place.
a. Raise the side panel so it is in a vertical position and put the side panel into
the rear socket.
b. Turn the side panel to the seat position and lower down the side panel. Make sure
the side panel is locked into the sockets.
The side panel can be ipped up and removed for entering the wheelchair conveniently.
SAFETY TIPS
a. Improper use of the side panel may result in damage to your health or damage
of the wheelchair sockets.
b. Make sure a clear “click” sound can be heard after side panel is mounted into the
wheelchair sockets, to signal it is locked in place.





ADJUSTABLE OF HANDLE HEIGHT
REAL WHEEL SAFETY TIPS
MOUNT/DISMOUNT THE REAR WHEEL
The push handle is used to offer convenience to the attendant
The height adjustable handle can only be adjusted by a professional.
a. The temperature may rise when reducing speed by the hand rim due to friction.
It is advised to wear a wheelchair pushing glove - these are available to purchase
from CareCo.
b. Fingers may be pinched or scratched during use of rear wheel.
Do not grab any part between the brake and the rear wheel.
Do not grab any part of the rims or between the rims.
The rear wheels are used for wheelchair movement, direction turning and stop.
The rear wheels can be taken out of the wheelchair for easy transportation.
a. grab the rims around the rear axle of the wheelchair.
b. Press the button on the quick release axle with thumb.
c. Mount or dismount the rear wheel. When the button is released, the quick release
axle is located in the wheel axles securely.



FRONT CASTOR/FORK SAFETY TIPS
CLIMBING A kURB
BRAKES
Improper mounting method of front fork and castor may result in the wheelchair tipping
over and causing injury.
Be careful when you make any front inclination movement for example (tie shoelaces),
always insure maximum wheelchair stability.
The front fork and castors are used to go forward or turn direction. A professional is
needed to mount/dismount the front fork and castor.
The wheelchair can climb a curb up to 10 degrees. The max. curb height is about 17.5%
of the front castors. Use of anti-tippers helps climb a larger curb.
It is strongly recommended that the wheelchair user climbs the curb with care and
assistance of an attendant. Anti-Tip Wheels are available to purchase from CareCo.
Brakes are intended to keep a stopped wheelchair from rolling especially on a slope.
Do not use it to stop the wheelchair suddenly when it is in movement. This may cause
trapped ngers, or even the wheelchair to tip over causing injury.
Always use brakes on both sides to stop the wheelchair gradually.
When stopped on a slope or in a transport vehicle, keep the wheelchair locked by brakes
at both sides. Do not put ngers or any part of your body between the brakes and the rear
wheel when the wheelchair is in movement.
Keep the brake at a proper distance from the wheel and keep a normal tire air pressure.
The recommended distance is 4mm. It may vary to each user.
The mounting or dismount of the wheelchair brakes must be done by a professional. The
user is forbidden to mount/dismount/adjust the brakes.
a. Push the brake lever handle forward to lock the wheels.
b. Lift the brake lever handle to release the locked wheels.


FOLDING THE WHEELCHAIR AND TRANSPORT
CLEANING
MAINTENANCE
Take out the padded seat from the wheelchair and lift the wheelchair from middle of the
seat so as to fold it.
Do not use the wheelchair when it is folded.
The folded wheelchair can not bear weight as it may distort and cause risk in use after it is
unfolded.
Do not put heavy objects on a folded wheelchair.
Use a vehicle to transport the wheelchair. Make sure the wheel brakes are locked in
transportation.
Do not use the wheelchair when it is in transportation.
It is forbidden by the manufacturer that a wheelchair is used in transportation vehicle. It
may cause serious damage and injury to the user.
The wheelchair user must use the seat in the transport vehicle during transportation.
a. Use mild detergent and warm water to clean.
b. Remove the dirt or blemish with a sponge or soft brush.
c. Use a damp cloth to remove the uids on the wheelchair.
d. Dry it after cleaning in water a few times.
e. Sterile the wheelchair parts when needed.
a. Periodic check is required for a wheelchair user.
Check the wheelchair special functions, especially the wheel brakes each time
before use. If any damaged component is found, please contact
CareCo immediately.
Check the general conditions of the wheelchair every month.
Check the rims on the rear wheel every 3 months.
If the user is youth or adolescent, keep it under guidance of a professional
attendant and every 6 months the wheelchair would need periodic check.
b. Safety nut can only be used once. Replace it if it is loose a few times.
c. Contact CareCo immediately if a defect is found, especially when there is abnormal
condition or the wheelchair is not stable.
d. It is recommended by manufacturer that the wheelchair be checked and
maintained by a professional every 12 months. It may have risk of potential
damage or injury without maintenance after use of 12 months.
e. The repair and maintenance can only be done by a professional from manufacturer
or CareCo.

Your CareCo branded product is under warranty to be free from defects in material and
workmanship for one year from date of purchase. This warranty expresses our condence in
workmanship and materials used for our products.
In the event of a defect covered by this warranty, CareCo will, at our discretion, replace the
wheelchair or provide parts to remedy. This warranty does not cover device failure due to
owner misuse or negligence, or due to normal wear and tear. The warranty does not extend to
non-durable parts, such as rubber accessories, castors, grips and arm pads, which are subject
to normal wear and tear and require periodic replacement.
If you have any queries please contact CareCo.
Warranty
CareCo, Hubert Road, Brentwood,
Essex CM14 4JE
www.careco.co.uk