Carrier 40VK S-8S-TST Series User manual

VRF High-Wall air conditioner
Model name:
40VK____S-8S-TST
Owner’s Manual 1English
่�ือการใ้งาน 32 ภาษาไทย
Owner’s
Manual
Notice: is committed to continuously improving its products to ensure the highest
quality and reliability standards, and to meet local regulations and market requirements.
All features and specications are subject to change without prior notice.
1130550209
For commercial use
ำ�หับใ้ง�นเิงพ�ิ์
00_1130550209_Cover.indd 100_1130550209_Cover.indd 1 7/7/2566 BE 16:007/7/2566 BE 16:00

Thank you very much for purchasing Air Conditioner.
Please read this Owner’s Manual carefully before using your Air Conditioner.
• Be sure to obtain the “Owner’s Manual” and “Installation Manual” from constructor (or dealer).
Request to constructor or dealer
• Please clearly explain the contents of the Owner’s Manual and hand over it.
NOTE
This manual describes operations of the indoor unit and the wireless remote controller.
For details of the wired remote controller and the outdoor unit, refer to the operation manual supplied with
the outdoor unit. (Keep these manuals carefully.)
ADOPTION OF NEW REFRIGERANT
This Air Conditioner is a new type which adopts a new refrigerant HFC (R410A) instead of the
conventional refrigerant R22 in order to prevent destruction of the ozone layer.
According to IEC 60335-1
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
According to EN 60335-1
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Original Instruction
- 1 -
01_1130550209_EN.indd 101_1130550209_EN.indd 1 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
1 PRECAUTIONS FOR SAFETY ..................................................................... 5
2 ACCESSORIES ........................................................................................... 11
3 PARTS NAME.............................................................................................. 11
4 PARTS NAME OF REMOTE CONTROLLER ............................................. 13
5 ADJUSTING CLOCK................................................................................... 15
6 LIMITED OPERATION BY GROUP CONTROL.......................................... 16
7 HANDLING THE REMOTE CONTROLLER................................................ 17
8 HOW TO USE REMOTE CONTROLLER.................................................... 18
9 HINTS FOR ECONOMICAL OPERATION .................................................. 25
10 TEMPORARY OPERATION ........................................................................ 26
11 MAINTENANCE........................................................................................... 27
12 TROUBLES AND CAUSES......................................................................... 30
Contents
- 2 -
01_1130550209_EN.indd 201_1130550209_EN.indd 2 7/7/2566 BE 16:007/7/2566 BE 16:00

Thank you very much for purchasing Air Conditioner.
Please read carefully through these instructions that contain important information and ensure
that you understand them.
After reading these instructions, be sure to keep them in a safe place together with the
Installation Manual supplied with your product.
Generic Denomination: Air Conditioner
Denition of Qualied Installer or Qualied Service Person
The air conditioner must be installed, maintained, repaired and removed by a qualied installer or
qualied service person. When any of these jobs is to be done, ask a qualied installer or qualied
service person to do them for you.
A qualied installer or qualied service person is an agent who has the qualications and knowledge
described in the table below.
Agent Qualications and knowledge which the agent must have
Qualied
installer
• The qualied installer is a person who installs, maintains, relocates and removes the air
conditioners. He or she has been trained to install, maintain, relocate and remove the air
conditioners or, alternatively, he or she has been instructed in such operations by an individual or
individuals who have been trained and is thus thoroughly acquainted with the knowledge related
to these operations.
• The qualied installer who is allowed to do the electrical work involved in installation, relocation
and removal has the qualications pertaining to this electrical work as stipulated by the local laws
and regulations, and he or she is a person who has been trained in matters relating to electrical
work on the air conditioners or, alternatively, he or she has been instructed in such matters by
an individual or individuals who have been trained and is thus thoroughly acquainted with the
knowledge related to this work.
• The qualied installer who is allowed to do the refrigerant handling and piping work involved in
installation, relocation and removal has the qualications pertaining to this refrigerant handling
and piping work as stipulated by the local laws and regulations, and he or she is a person
who has been trained in matters relating to refrigerant handling and piping work on the air
conditioners or, alternatively, he or she has been instructed in such matters by an individual or
individuals who have been trained and is thus thoroughly acquainted with the knowledge related
to this work.
• The qualied installer who is allowed to work at heights has been trained in matters relating to
working at heights with the air conditioners or, alternatively, he or she has been instructed in such
matters by an individual or individuals who have been trained and is thus thoroughly acquainted
with the knowledge related to this work.
Qualied
service
person
• The qualied service person is a person who installs, repairs, maintains, relocates and removes
the air conditioners. He or she has been trained to install, repair, maintain, relocate and remove
the air conditioners or, alternatively, he or she has been instructed in such operations by an
individual or individuals who have been trained and is thus thoroughly acquainted with the
knowledge related to these operations.
• The qualied service person who is allowed to do the electrical work involved in installation,
repair, relocation and removal has the qualications pertaining to this electrical work as stipulated
by the local laws and regulations, and he or she is a person who has been trained in matters
relating to electrical work on the air conditioners or, alternatively, he or she has been instructed
in such matters by an individual or individuals who have been trained and is thus thoroughly
acquainted with the knowledge related to this work.
• The qualied service person who is allowed to do the refrigerant handling and piping work
involved in installation, repair, relocation and removal has the qualications pertaining to this
refrigerant handling and piping work as stipulated by the local laws and regulations, and he
or she is a person who has been trained in matters relating to refrigerant handling and piping
work on the air conditioners or, alternatively, he or she has been instructed in such matters by
an individual or individuals who have been trained and is thus thoroughly acquainted with the
knowledge related to this work.
• The qualied service person who is allowed to work at heights has been trained in matters
relating to working at heights with the air conditioners or, alternatively, he or she has been
instructed in such matters by an individual or individuals who have been trained and is thus
thoroughly acquainted with the knowledge related to this work.
- 3 -
01_1130550209_EN.indd 301_1130550209_EN.indd 3 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
■Warning indications on the air conditioner unit
Warning indication Description
WARNING
ELECTRICAL SHOCK HAZARD
Disconnect all remote
electric power supplies
before servicing.
WARNING
ELECTRICAL SHOCK HAZARD
Disconnect all remote electric power supplies before
servicing.
WARNING
Moving parts.
Do not operate unit with grille
removed.
Stop the unit before the servicing.
WARNING
Moving parts.
Do not operate unit with grille removed.
Stop the unit before the servicing.
CAUTION
High temperature parts.
You might get burned
when removing this panel.
CAUTION
High temperature parts.
You might get burned when removing this panel.
CAUTION
Do not touch the aluminum
fins of the unit.
Doing so may result in injury.
CAUTION
Do not touch the aluminum ns of the unit.
Doing so may result in injury.
CAUTION
BURST HAZARD
Open the service valves before
the operation, otherwise there
might be the burst.
CAUTION
BURST HAZARD
Open the service valves before the operation, otherwise
there might be the burst.
- 4 -
01_1130550209_EN.indd 401_1130550209_EN.indd 4 7/7/2566 BE 16:007/7/2566 BE 16:00

1 PRECAUTIONS FOR SAFETY
DANGER
• Do not attempt to install this unit by yourself.
This unit requires qualied installer.
• Do not attempt to repair the unit by yourself.
This unit has no components which you can repair.
• Opening or removing the cover will expose you to
dangerous voltage.
• Turning off the power supply will not prevent potential
electric shock.
The manufacturer shall not assume any liability for the damage caused by not
observing the description of this manual.
WARNING
General
• Carefully read Owner’s Manual before starting the air conditioner. There are
many important things to keep in mind for daily operation.
• Ask for installation to be performed by the dealer or a professional. Only a
qualied installer (*1) is able to install an air conditioner. If a non-qualied
person installs an air conditioner, it may result in problems such as re,
electric shock, injury, water leakage, noise and vibration.
• Do not use any refrigerant different from the one specied for complement or
replacement. Otherwise, abnormally high pressure may be generated in the
refrigeration cycle, which may result in a failure or explosion of the product or
an injury to your body.
• Do not add any other devices without factory advice.
• Places where the operation sound of the outdoor unit may cause a
disturbance. (Especially at the boundary line with a neighbour, install the air
conditioner while considering the noise.)
• This appliance is intended to be used by expert or trained users in shops, in
light industry, or for commercial use by lay persons.
Transportation and storage
• To transport the air conditioner, wear shoes with protective toe caps,
protective gloves, and other protective clothing.
• To transport the air conditioner, do not take hold of the bands around the
packing carton. You may injure yourself if the bands should break.
• Before stacking the packing cartons for storage or transportation, heed the
precautions written on the packing cartons. Failure to heed the precautions
may cause the stack to collapse.
• The air conditioner must be transported in stable condition. If any part of the
product broken, contact your dealer.
- 5 -
01_1130550209_EN.indd 501_1130550209_EN.indd 5 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
• When the air conditioner must be transported by hand, carry it by two or
more people.
Installation
• Only a qualied installer (*1) or qualied service person (*1) is allowed to
carry out the electrical work of the air conditioner. Under no circumstances
must this work be done by an unqualied individual since failure to carry out
the work properly may result in electric shocks and/or electrical leaks.
• After the installation work has been completed, have the installer explain
about the circuit breaker positions. In the event that trouble has occurred in
the air conditioner, set the circuit breaker to the OFF position, and contact a
qualied service person (*1).
• If the unit is installed in a small room, take appropriate measures to prevent
the refrigerant from exceeding the limit concentration even if it leaks.
Consult the dealer from whom you purchased the air conditioner when you
implement the measures. Accumulation of highly concentrated refrigerant
may cause an oxygen deciency accident.
• Do not install the air conditioner in a location that may be subject to a risk
of exposure to a combustible gas. If a combustible gas leaks and becomes
concentrated around the unit, a re may occur.
• Use the company-specied products for the separately purchased parts. Use
of non-specied products may result in re, electric shock, water leakage or
other trouble. Have the installation performed by a professional.
• Conrm that earthing is performed correctly.
Operation
• Before opening the front panel of the indoor unit or service panel of the
outdoor unit, set the circuit breaker to the OFF position. Failure to set the
circuit breaker to the OFF position may result in electric shocks through
contact with the interior parts. Only a qualied installer (*1) or qualied
service person (*1) is allowed to remove the front panel of the indoor unit or
service panel of the outdoor unit and do the work required.
• Inside the air conditioner are high-voltage areas and rotating parts. Due to
the danger of electric shocks or of your ngers or physical objects becoming
trapped in the rotating parts, do not remove the front panel of the indoor unit
or service panel of the outdoor unit. When work involving the removal of
these parts is required, contact a qualied installer (*1) or qualied service
person (*1).
• Do not move or repair any unit by yourself. Since there is high voltage
inside the unit, you may get electric shock when the cover and main unit is
removed.
• Use of a stand more than 50 cm high to clean the lter of the indoor unit or to
carry out other such jobs constitutes working at heights. Due to the danger of
falling off the stand and injuring yourself while working at heights, this kind of
work should not be done by unqualied individuals. When this kind of work
must be carried out, do not do it yourself but ask a qualied installer (*1) or
qualied service person (*1) to do it for you.
- 6 -
01_1130550209_EN.indd 601_1130550209_EN.indd 6 7/7/2566 BE 16:007/7/2566 BE 16:00

• Do not touch the aluminum n of the outdoor unit. You may injure yourself if
you do so. If the n must be touched, do not touch it yourself but contact a
qualied installer (*1) or qualied service person (*1).
• Do not climb onto or place objects on top of the outdoor unit. You may fall or
the objects may fall off of the outdoor unit and result in injury.
• Do not place any combustion appliance in a place where it is directly
exposed to the wind of air conditioner, otherwise it may cause imperfect
combustion.
• When the air conditioner is operated with a combustion appliance in the
same place, ventilate the room sufciently. Poor ventilation causes oxygen
shortage.
• When the air conditioner is used in a closed room, sufciently ventilate the
room. Poor ventilation causes oxygen shortage.
• Do not expose your body to cool air directly for a long time and do not cool
yourself excessively. Doing so may result in deteriorated physical condition
and ill health.
• Do not insert your nger or a stick into the air intake or discharge. Doing so
may result injury as the fan is rotating at high speed inside the unit.
• Consult the shop where you purchased the air conditioner if air conditioning
(cooling) is not performed properly as a refrigerant leakage may be
the cause. Conrm the repair details with a qualied service person (*1)
when the repair includes additional charging of the refrigerant.
• Stop running the air conditioner and turn off the breaker before cleaning.
Otherwise, injury may result as the fan is rotating at high speed inside the
unit.
Repairs
• If there is any kind of trouble (such as when an error display has appeared,
there is a smell of burning, abnormal sounds are heard, the air conditioner
fails to cool or heat or water is leaking) has occurred in the air conditioner,
do not touch the air conditioner yourself but set the circuit breaker to the
OFF position, and contact a qualied service person (*1). Take steps to
ensure that the power will not be turned on (by marking “out of service”
near the circuit breaker, for instance) until qualied service person (*1)
arrives. Continuing to use the air conditioner in the trouble status may cause
mechanical problems to escalate or result in electric shocks or other trouble.
• If the fan grille is damaged, do not approach the outdoor unit but set the
circuit breaker to the OFF position, and contact a qualied service person
(*1) to have the repairs done. Do not set the circuit breaker to the ON
position until the repairs are completed.
• If there is a danger of the indoor unit’s falling, do not approach the indoor
unit but set the circuit breaker to the OFF position, and contact a qualied
installer (*1) or a qualied service person (*1) to ret the unit. Do not set the
circuit breaker to the ON position until the unit has been retted.
• If there is a danger of the outdoor unit’s toppling over, do not approach the
outdoor unit but set the circuit breaker to the OFF position, and contact
- 7 -
01_1130550209_EN.indd 701_1130550209_EN.indd 7 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
a qualied installer (*1) or a qualied service person (*1) to have the
improvements or retting done. Do not set the circuit breaker to the ON
position until the improvements or retting is completed.
• Do not customize the unit. Doing so may result in re, electric shock or other
trouble.
Relocation
• When the air conditioner is to be relocated, do not relocate it yourself but
contact a qualied installer (*1) or a qualied service person (*1). Failure to
relocate the air conditioner properly may result in electric shocks and/or a re.
CAUTION
To disconnect the appliance from the mains supply.
• This appliance must be connected to the mains by means of a switch with a
contact separation of at least 3 mm.
The installation fuse (all types can be used) must be used for the power
supply line of this air conditioner.
Installation
• Certainly lay the drain hose for perfect draining. Bad drainage may cause
ooding in the house and getting furniture wet.
• Connect the air conditioner to an exclusive power supply of the rated
voltage, otherwise the unit may break down or cause a re.
• Conrm that the outdoor unit are xed on the base. Otherwise, falling down
of the units or other accidents may occur.
Operation
• Do not use this air conditioner for special purpose such as preserving food,
precision instruments, art objects, breeding animals, car, vessel.
• Do not touch any switches with wet nger, otherwise you may get an electric
shock.
• If the air conditioner will not be used for a considerably long time, turn off the
main switch or the circuit breaker, for safety.
• To make the air conditioner operate in its original performance, operate it
within the range of the operating temperature specied in the instructions.
Otherwise it may cause a malfunction, or water leak from the unit.
• Prevent any liquid from falling into the remote controller. Do not spill juice,
water or any kind of liquid.
• Do not wash the air conditioner. Doing so may result in electric shock.
• Check whether the installation base and other equipment have become
deteriorated after being used for a long time. Leaving them such condition
may result in the unit’s falling down and causing injury.
• Do not leave ammable sprays or other ammable materials near the
air conditioner, and do not spray ammable aerosol directly to the air
conditioner. They may catch re.
- 8 -
01_1130550209_EN.indd 801_1130550209_EN.indd 8 7/7/2566 BE 16:007/7/2566 BE 16:00

• Stop running the air conditioner and turn off the breaker before cleaning.
Otherwise, injury may result as the fan is rotating at high speed inside the
unit.
• Ask for cleaning of the air conditioner to be performed by the dealer.
Cleaning the air conditioner in an improper manner may cause damage to
plastic parts, insulation failure of electric parts and result in a malfunction.
In the worst case, it may result in water leakage, electric shock, smoke
emission and re.
• Do not put a water container such as a vase on the unit. Water intrusion into
the unit may occur and it may cause deterioration of electric insulation and
result in electric shock.
• Do not wash air conditioners with pressure washers. Electric leakage may
cause electric shocks or res.
(*1) Refer to the “Denition of Qualied Installer or Qualied Service Person.”
- 9 -
01_1130550209_EN.indd 901_1130550209_EN.indd 9 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
■Information on the transportation, handling and storage of the carton
◆Examples of indication on the carton
Symbol Description Symbol Description
Keep dry Do not drop
Fragile Do not lay down
7
7
Stacking height
(8 cartons can be stacked in
this case)
Do not step
This side up Handle with care
Other cautions Description
CAUTION
Injury possibility.
Don’t handle with packing band, or may get injured in
case of broken band.
- 10 -
01_1130550209_EN.indd 1001_1130550209_EN.indd 10 7/7/2566 BE 16:007/7/2566 BE 16:00

2 ACCESSORIES
Remote controller Remote controller holder Batteries (two)
3 PARTS NAME
■Indoor unit
34
12
5 6 7 8 9,10
1211
1Air inlet grille 7Horizontal airow louver (back)
2Air lter 8Vertical airow louver
3Room temperature sensor 9Display panel
4Front panel 10 Infrared signal receiver
5Air outlet 11 Remote controller (wireless)
6Horizontal airow louver (front) 12 Remote controller (wired, sold separately)
- 11 -
01_1130550209_EN.indd 1101_1130550209_EN.indd 11 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
■Names and functions of
indicators and controls on
indoor unit
Display panel
123
The operating conditions are indicated below.
1OPERATION (White)
This lamp goes on during operation.
2TIMER (White)
This lamp goes on white the timer reserved.
NOTE
In case of timer setting by wired remote controller,
TIMER lamp does not light.
In case of group control, TIMER lamp goes on
header unit only. (see “6 LIMITED OPERATION
BY GROUP CONTROL”)
3Preheat/Defrost (White)
This lamp lights up when the power is turned on
(Initialize) or lights up when a trouble occurs, trouble
code is displayed.
CAUTION
• Disagreement in operation mode
If you select AUTOMATIC OPERATION in a
model with no auto-changeover (cooling) control
setting an alarm sound (pi, pi) from the air
conditioner due to disagreement in operation
mode. Change the operation mode with the
MODE button on the wireless remote controller.
This disagreement indication cannot be deleted
by the wired remote controller.
• When local prohibition is set by the central
control from other equipment, no signal is
received even if the remote controller button is
pressed. However, a signal of START/STOP
button is accepted. (An alarm sound “pi ” arises
intermittently ve times.)
TEMPORARY operation
If you misplace or lose the wireless remote
controller or its batteries are exhausted, push the
[RESET] button.
• Push the [RESET] button to start the air
conditioner.
Push this button once again to stop it.
OPERATION/
RESET Button
- 12 -
01_1130550209_EN.indd 1201_1130550209_EN.indd 12 7/7/2566 BE 16:007/7/2566 BE 16:00

4 PARTS NAME OF REMOTE CONTROLLER
■Wireless remote controller and its
functions
ECO
SLEEP
1
24
6
5
15
12
11
8
10
3
7
9
14
13
1Infrared signal emitter
Transmits a signal to the indoor unit.
2START/STOP button
Press the button to start operation.
(A receiving beep is heard.)
Press the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor unit,
press the button twice.
3Mode select button ( )
Press this button to select a mode.
Each time you press the button, a mode is selected
in a sequence that goes from A : Auto changeover
control, : Cool, : Dry, : Fan only, and back
to A. (A receiving beep is heard.)
4Temperature button ( )
...........The set temperature is increased up to
30°C.
...........The set temperature is dropped down to
17°C. (A receiving beep is heard.)
5Fan speed button ( )
Press this button to select fan speed.
When you select AUTO, the fan speed is
automatically adjusted according to the room
temperature.
You can also manually select the desired fan speed
from among ve settings.
(LOW , LOW+, MED ,
MED+, HIGH )
(A receiving beep is heard.)
6Auto louver button ( )
Press this button to swing the louver.
(A receiving beep is heard.)
Press the SWING button to stop the louver
swinging.
(A receiving beep is heard.)
7Set louver button ( )
Press this button to adjust the airow direction.
(A receiving beep is heard.) While this FIX button
is kept depressed, the receiving tone continuously
sounds.
8Off timer button ( )
Press this button to set the OFF timer.
9On timer button ( )
Press this button to set the ON timer.
10 Reserve button ( )
Press this button to reserve time settings.
(A receiving beep is heard.)
11 Cancel button ( )
Press this button to cancel ON timer and OFF timer.
(A receiving beep is heard.)
12 High power button ( )
Press this button to start the high power operation.
This function is not operated group control.
13 PRESET button ( )
Press this button to change the operation mode to
the preferred operation mode memorized previously.
To memorize the operation mode, press this button
for at least 3 seconds during the preferred operation
mode.
Pis displayed and the operation mode is
memorized.
14 ECO SLEEP button (
ECO
SLEEP
)
Press this button to start the OFF timer operation
that automatically adjusts the room temperature and
the fan speed.
You can select the OFF timer time from four
durations (1, 3, 5 or 9 hours).
During group control operation, the set temperature
and the fan speed are not automatically adjusted.
Only off timer function is activated.
15 QUIET button ( )
Press this button to start quiet operation.
Pressing this button again will restore normal
operation.
- 13 -
01_1130550209_EN.indd 1301_1130550209_EN.indd 13 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
■Names and functions of
indications on wireless remote
controller
Display
All indications, except for clock time indication, are
indicated by pressing the START/STOP
button.
10
7
5
4
6
9
8
1 2
3
• In the illustration, all indications are indicated for
explanation.
During operation, only the relevant indications
will be indicated on the remote controller.
1Transmission mark
This transmission mark ( ) indicates when the
remote controller transmits signals to the indoor unit.
2Mode display
Indicates the current operation mode.
(A : Auto changeover control, : Cool, : Dry,
: Fan only)
3Temperature display
Indicates the temperature setting (17°C to 30°C).
When you set the operating mode to : Fan only,
no temperature setting is indicated.
4FAN speed display
Indicates the selected fan speed. AUTO or one of ve
fan speed levels (LOW , LOW
+
, MED ,
MED
+
, HIGH ) can be indicated.
Indicates when the operating mode is : Dry.
5TIMER and clock time display
The time set for timer operation or clock time is
indicated.
The present time is always indicated except for
TIMER operation.
6Hi POWER display
Indicates when the high power operation starts.
Press the Hi POWER button to start and press it
again to stop the operation.
7P (PRESET) display
Indicated when memorizing the preferred operation
mode or when it has been memorized.
Also, this icon is indicated when the memorized
preferred operation is displayed.
8 (ECO SLEEP) display
Indicated during the OFF timer operation that
automatically adjusts the room temperature and the
fan speed. Each time you press the ECO SLEEP
button, the display changes in the sequence
of 1h, 3h, 5h, and 9h.
9 (QUIET) display
Indicated during the quiet operation.
10 Swing display
Indicated during the swinging operation where the
horizontal louver automatically moves up and down.
NOTE
When both wired remote controller and wireless
remote controller are used, display on the screen
of wireless remote controller may differ from the
actual operation in some cases.
■Preparation and check before use
1.Loading Batteries
• Remove the battery
cover.
• Insert 2 new batteries
(R03 [AAA]) following
the (+) and (-)
positions.
2.Removing Batteries
• Remove the battery
cover.
• Remove the 2 used
batteries.
Batteries
• To replace the batteries, use two new batteries
(R03 [AAA]).
• In normal use, the batteries will last about one
year.
• Replace the batteries if there is no receiving
beep from the indoor unit or when the air
conditioner cannot be operated using the remote
controller.
• To avoid malfunctions by battery leakage,
remove the batteries when not using the remote
controller for more than one month.
• Please dispose of the used batteries according to
the local regulation.
- 14 -
01_1130550209_EN.indd 1401_1130550209_EN.indd 14 7/7/2566 BE 16:007/7/2566 BE 16:00

5 ADJUSTING CLOCK
Setting the clock
Before you start operating the air conditioner,
set the clock of the remote controller using the
procedures given in this section. The clock panel
on the remote controller will indicate the time
regardless of whether the air conditioner is in use
or not.
■Initial setting
When batteries are inserted in the remote
controller the clock panel will indicate AM 0:00 and
will ash.
ECO
SLEEP
2
1
1TIMER or button
Press the TIMER or button to set the current
time.
Each press of the TIMER button changes the time in
one minute steps.
Pressing the TIMER button continually changes the
time in ten minute steps.
2SET button
Press the SET button.
The current time is indicated and the clock starts.
■Clock adjusting
ECO
SLEEP
3
2
1
1CLOCK button
Press the CLOCK by tip of a pencil.
The CLOCK display ashes.
2TIMER or button
Press the TIMER or button to set the current
time.
Each press of the TIMER button changes the time by
one minute.
Pressing the TIMER button continually changes the
time by ten minutes.
3SET button
Press the SET button.
The current time is indicated and the clock starts.
- 15 -
01_1130550209_EN.indd 1501_1130550209_EN.indd 15 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
6 LIMITED OPERATION BY GROUP CONTROL
NOTE
Group control: Operate air conditioners in more than one system in same time.
Header indoor unit: The representative unit during group control. Receive commands from wired remote
controller and transmit the commands to follower units.
(Header indoor unit is indoor unit that receives START/STOP signal from the wireless remote controller.)
Follower indoor unit: Indoor units other than the Header unit are called follower unit.
A wired remote controller (separately available) is required for the group control.
▼Example of group combination
Indoor
Wired remote controller
Outdoor
Indoor
Outdoor
Indoor
Control line
Other connecting line
Outdoor
CAUTION
When using indoor unit in group control,
1. Hi POWER operation will not function.
When Hi POWER is transmitted from wireless remote controller, the receiving sound will be heard from
the indoor unit and display on the wireless remote controller will also change. However, the indoor unit
does not operate Hi POWER operation. Restore the display on the wireless remote controller pushing
Hi POWER button.
2. ECO SLEEP
When ECO SLEEP is transmitted from wireless remote controller, the receiving sound will be heard
from the indoor unit and the display on the wireless remote controller will also be changed as same
as Hi POWER operation. However, the set temperature and the fan speed will not be automatically
adjusted. Only off timer function is activated.
3. Units other than the Header unit cannot be operated with remote controller and the
TEMPORARY operation.
When operating air conditioner with wireless remote controller transmission should be sent to the
Header unit.
Header and follower indoor units are decided through address setting upon installation. Follower unit
will not receive any signals from wireless remote controller.
Air conditioner will not work even if the [RESET] button on the follower unit is pressed.
(Some Follower units may receive SWING and FIX, but these operations are performed only on the
unit that received the signal.)
(When wireless remote controller is used, only the Header unit receives SWING signal. If the SWING
signal is transmitted to follower unit, the sound to refuse receiving signal (3 beeps) is heard and the
follower unit does not receive the signal.
For FIX operation, both Header and follower unit perform the operation by itself. When wired remote
controller is used, airow direction can be changed on each unit by selecting the indoor unit.)
4. TIMER lamp lights up only on the Header unit.
When the timer is set with wired remote controller, even the TIMER lamp on the Header unit will not
light up.
- 16 -
01_1130550209_EN.indd 1601_1130550209_EN.indd 16 7/7/2566 BE 16:007/7/2566 BE 16:00

7 HANDLING THE REMOTE CONTROLLER
CAUTION
• The air conditioner will not operate if curtains,
doors or other materials block the signals from
the remote controller to the indoor unit.
• Prevent any liquid from falling into the remote
controller.
Do not expose the remote controller to direct
sunlight or heat.
• If the infrared signal receiver on the indoor unit
is exposed to direct sunlight, the air conditioner
may not function properly.
Use curtains to prevent the sunlight from
reaching the receiver.
• If the room using the air conditioner has
uorescent lighting with electronic starters,
signals may not be properly received. If you are
planning to use such uorescent lamps, consult
your local dealer.
• If other electrical appliances react to the remote
controller move these appliances or consult your
local dealer.
■Location of the remote controller
• Keep the remote controller where its signals can
reach the receiver of the indoor unit (a distance
of 7 m is allowed).
• When you select the timer operation, the remote
controller automatically transmits a signal to the
indoor unit at the specied time.
If you keep the remote controller in a position
that hinders proper signal transmission, a time
lag of up to 15 minutes may occur.
7 m
■Remote controller holder
Installing the remote controller holder
• Before you actually install the remote controller
holder on a wall or pillar, check whether the
remote controller signals can be received by the
indoor unit.
Mounting and removing the remote
controller
• To mount the remote controller hold it parallel to
the remote controller holder and push it in fully.
• To remove the remote controller slide the remote
controller upwards and out from the holder.
- 17 -
01_1130550209_EN.indd 1701_1130550209_EN.indd 17 7/7/2566 BE 16:007/7/2566 BE 16:00

EN
8 HOW TO USE REMOTE CONTROLLER
■
Cooling / fan only operation
Start
4
3
1
2
1START/STOP button ( )
Press this button to start the air conditioner.
2Mode select button ( )
Select Cool or Fan only .
3Temperature button ( )
Set the desired temperature.
When the air conditioner is in FAN ONLY operation,
the temperature display is not indicated.
4Fan speed button ( )
Select one of LOW , LOW+,
MED , MED+, HIGH .
• The OPERATION lamp on the display panel
of the indoor unit goes on. And operation starts
after approximately 3 minutes. (If you select FAN
ONLY mode, the unit will start immediately.)
• The : Fan only mode does not control
temperature.
• Fan speed is the same as
HIGH .
Therefore, perform only steps 1, 2and 4to
select this mode.
Stop
START/STOP button ( )
Press this button again to stop the air conditioner.
■Dry operation
Start
3
1
2
1START/STOP button ( )
Press this button to start the air conditioner.
2Mode select button ( )
Select Dry .
3Temperature button ( )
Set the desired temperature.
• The fan speed display indicates .
• The OPERATION lamp on the display panel
of the indoor unit lights, and operation starts after
approximately 3 minutes.
Stop
START/STOP button ( )
Press this button again to stop the air conditioner.
- 18 -
01_1130550209_EN.indd 1801_1130550209_EN.indd 18 7/7/2566 BE 16:007/7/2566 BE 16:00

■
Automatic operation
(auto changeover)
This function is available only for use in
combination with a heat recovery model outdoor
unit. If this function is used with another model of
outdoor unit, “A” (Auto) appears on the remote
controller but the automatic operation is disabled.
Start
4
3
1
2
1START/STOP button ( )
Press this button to start the air conditioner.
2Mode select button ( )
Select A.
3Temperature button ( )
Set the desired temperature.
4Fan speed button ( )
Select one of LOW , LOW+,
MED , MED+, HIGH .
• The OPERATION lamp on the display panel
of the indoor unit lights.
The operating mode is selected in accordance
with the room temperature and operation starts
after approximately 3 minutes.
• If the “A” mode is uncomfortable, you can select
the desired conditions manually.
Stop
START/STOP button ( )
Press this button again to stop the air conditioner.
CAUTION
Disagreement in operation mode
If you select AUTOMATIC OPERATION in a model
with no auto-changeover (cooling) control setting,
lamp lights up and and lamps blink
alternately with an alarm sound (pi, pi) from the air
conditioner due to disagreement in operation mode.
Change the operation mode with the MODE button
on the wireless remote controller.
This disagreement indication cannot be deleted by
the wired remote controller.
■Timer operation
Use the wired remote controller for timer setting if it
is also in use.
ON timer and OFF timer
ECO
SLEEP
2
3
1
Setting TIMER
1ON/OFF TIMER button ( or )
Press the ON or OFF TIMER buttons as required.
• The previous timer setting is displayed and ashes
along with ON/OFF timer display.
Set the timer to the desired time.
Each press of the TIMER button changes the
time in ten minute steps.
Pressing the TIMER button continually changes
the time in one hour step.
2SET button
Press the SET button to set the timer.
The timer time is indicated and the timer starts.
Cancelling TIMER
3CLR button
Press the CLR button to cancel the timer setting.
CAUTION
• When you select the timer operation, the remote
controller automatically transmits the timer signal
to the indoor unit at the specied time. Therefore,
keep the remote controller in a location where it
can transmit the signal to the indoor unit properly.
Otherwise, the time lag of up to 15 minutes will
occur.
• If you do not press the SET button within
30 seconds after setting the time, the setting will
be cancelled.
- 19 -
01_1130550209_EN.indd 1901_1130550209_EN.indd 19 7/7/2566 BE 16:007/7/2566 BE 16:00