Carrier 30HW-900-008 User manual

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No.04-53300194-01 Printed in U.S.A. Form 30-36SI Pg 1 10-18 Replaces: New
Installation Instructions
Part No. 30HW-900---008, 30MP-900---021
SAFETY CONSIDERATIONS
Installation of this accessory can be hazardous due to sys-
tem pressures, electrical components and equipment location.
Only trained, qualified installers and service mechanics should
install and service this equipment.
When installing this accessory, observe precautions in the
literature, labels attached to the equipment, and other safety
precautions that apply.
• Follow all safety codes.
• Wear safety glasses and work gloves.
• Use care in handling and installing this accessory.
USAGE
INTRODUCTION
Install this package after bringing unit into the building. For
30MPA, MPE, MPW units, and 19XR pumpout unit, the unit
must be raised off from the shipping skid by approximately 6
inches. After the accessory mobility package is installed, the
unit can be moved to its final location.
PACKAGE CONTENTS
INSTALLATION
30MP Chillers
1. Examine the package contents. The 30MP units require 6
wheels. Check to be sure there are 6 wheel assemblies in
the carton. Each wheel requires 4 bolts, 8 flat washers, 4
lock washers, and 4 nuts. Notify your Carrier representa-
tive if pieces are missing or if the accessory is damaged.
2. Jack up the unit to a height of approximately 6 in. above
the floor and block it in place. Be sure to block the unit
securely so that it cannot fall during installation of the
mobility package.
3. Mount the wheel assemblies to the unit. Mount one wheel
assembly with lock to the baseframe mounting points 3
and 4 as shown in Fig. 1 and 2. Mount one wheel assem-
bly without lock to the baseframe mounting points 1, 2, 5
and 6 as shown in Fig. 1 and 2.
4. Tighten each nut so that it holds the wheel assembly se-
curely once the assembly is mounted on the unit. A mini-
mum torque of 12 ft-lb (16 Nm) is recommended.
5. Remove the blocks, and carefully place unit back onto the
floor. The unit is now ready to roll to the desired location.
PART NO. UNIT
30HW-900---008
19XR04026501
19XR04026502
19XR04026503
30MP-900---021 30MPA,MPW016-071, 30MPE
PART NO. QUANTITY ITEM
30HW-900---008 4Wheel assemblies (includes
wheel, nut, and washer)
4Spacers
30MP-900---021
2Wheel Assemblies with Locks
4Wheel Assemblies without Locks
24 5/16-in.-18 x 1.0 in. Bolts
24 5/16-in.-18 Nuts
24 5/16-in. Lock Washers
48 5/16-in. Flat Washers
+
1
+
2
+
3
+
4
TOP VIEW
CONTROL BOX
50.30
(1278)
+
5
+
6
27.00
(686)
25.15
(639)
Fig. 1 — Baseframe Mounting Points, 30MPA,
MPE, and MPW Units
NOTE: Dimensions in ( ) are in mm.
19XR
30MPA, MPE, MPW
Mobility Package Accessory

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No.04-53300194-01 Printed in U.S.A. Form 30-36SI Pg 2 10-18 Replaces: New
© Carrier Corporation 2018
19XR Pumpout Units
1. Examine the package contents. Check to be sure there are
4 wheel assemblies in the carton. Spacers are included in
the carton but are not used and can be discarded. Notify
your Carrier representative if pieces are missing or if the
accessory is damaged.
2. Remove 4 lag bolts attaching the unit to the skid and dis-
card the bolts.
3. Jack up the unit to a height of approximately 6 in. above
the shipping skid and block in place. Be sure to block the
unit securely so that it cannot fall during installation of
the mobility package.
4. Mount the wheel assemblies to the unit. Mount one wheel
assembly to each of the basepan mounting holes as
shown in Fig. 3. Use the same mounting holes from
which the lag bolts were removed in Step 2. Tighten the
nut so that it holds the wheel assembly securely once the
assembly is mounted on the unit. A minimum torque of
20 ft-lb (27 Nm) is recommended.
5. Remove the shipping skid from under the unit, remove
the blocks, and carefully place unit back onto the floor.
The unit is now ready to roll to the desired location.
BOLT
WASHER
NUT
LOCK WASHER
WASHER
Fig. 2 — Mounting Wheel Assembly, 30MPA, MPE,
and MPW Units
NOTE: Non-locking wheel shown.
BASEPAN
WASHER*
NUT*
*Part of wheel assembly.
Fig. 3 — Mounting Wheel Assembly to
Pumpout Assembly Basepan, 19XR Units