SPEAKER CABLES
12 gauge Twist-lock speaker cables will provide a secure connection and high
current transfer of power to the speakers. You can also use standard 1/4" speaker
cables instead of the Twist-Lock cables provided they are at least 16 gauge. You
can DAISY-CHAIN up to one additional speaker per cable by using the unused
OUTPUT jack (right side) on your speaker jack plate. Be sure to note the total
impedance to the amp so it is not lower than it’s recommended impedance. See
Typical Loudspeaker Impedance Configurations.
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless
otherwise stated. Warranty coverage is limited to original manufactures defects
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs. DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be returned
COD for the cost of shipping and reconditioning if not covered under warranty.
MODEL RL210T BASS SPEAKER SYSTEM SPECS:
Frequency Response: 64 Hz to 16k Hz
Drivers: Two 10” PS10 Woofers & one PS1080 Horn
Power Handling: 400 watts
Horn Attenuation: Switch attenuation (reduction) in 3dB steps
Horn Protection: Yes—Maintenance Free
Coverage Angles: 90° Horizontal, 90° Vertical
Nominal Impedance: 4Ω
Input Connector:
One 1/4" Phone Connector/one Twist-Lock
Output Connector:
One 1/4" Phone Connector/one Twist-Lock
Woofer Enclosure Type: Vented Box
Enclosure Covering: Duratuff II™
Dimensions: 23.5"W x 18.25"D x 17.5"H
Warranty: One Year
Weight: 50 lbs.
Optional
Vinyl Cover: CVS210
CARVIN ENGINEERING DATA RL210T BASS SPEAKER SYSTEM INSTRUCTIONS
RL210T
The RL210T is a two-10” speaker system designed for the professional who wants
the absolute best in bass guitar amplification. With 2 heavy duty ten inch woofers
and an adjustable high frequency “Red Eye” compression driver, your sound will be
crisp and clear even at the highest sound pressure levels. You will get clean,
punchy, uncolored bass reproduction from an all new cabinet & cross-over design.
The new Duratuff II™ covered cabinet is 18 inches deep and is “front shelf” ported
for a full, deep sound.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion with your
name and comments to us.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
76-RL210 0801
12340 World Trade Drive, San Diego, CA 92128
800.854.2235 www.carvin.com
REAR CONNECT PLATE
Two standard 1/4" phone jacks and two
high current Twist-lock connectors are
featured. One for connecting to the
power amp and the other for connecting
to an additional speaker system.
Accepts Twist-lock & 1/4” cables
HORN ATTENUATION SWITCHES
The rear crossover panel features a set of attenuation
switches to control the volume of the “Red Eye” horn.
This will allow you to turn the horn full on or reduce by
3dB increments to fine tune your treble response.
