CARVIN TRC-A Series User manual

TRC600A or
TRC610A
10,000W
• 4 TRx3903 columns
• 4 TRx3018A or TRx3010A
subs
• 4 PRO5TL cables
• 4 SS7 inter-poles
• 2 CB3903 cases
TRC200A or
TRC210A
2500W
• 2 TRx3903 columns
• 1 TRx3018A or TRx3010A sub
• 1 PRO1TL cable
• 1 PRO5TL cable
• 2 SS7 inter-poles
• CB3903 case
TRC400A or
TRC410A
5000W
• 4 TRx3903 columns
• 2 TRx3018A or TRx3010A
subs
• 2 PRO1TL cables
• 2 PRO5TL cables
• 4 SS7 inter-poles
• 2 CB3903 cases
Systems
also
available
in
White
Powered Subwoofers
TRx3018A or TRx3010A
RECEIVING INSPECTION—please read before getting started
INSPECT YOUR UNIT FOR DAMAGE, which may have occurred during shipping. If damage
is found, please notify the shipping company and CARVIN AUDIO immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. This will provide the best possible
protection during shipment. CARVIN and the shipping company are not liable for any damage
caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately.
Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBERS on the enclosed warranty card for your records. Keep your
portion of the card and return the portion with your name and comments to us.
• Easy to connect - systems set up in a few minutes
• High level, dynamic sound for live performances
• Even coverage of the whole listening area from one system
• Amazing clarity and intelligibility
• Advanced design solves difcult room acoustics
• Up to 10,000 watts of DSP system power
• Installation or portable use
• Small to large venues
• Built in the USA
COMPLETE SYSTEMS
TRx3903 Column
TRC-A
POWERED COLUMN ARRAY SYSTEMS
TRC200A - TRC400A - TRC600A
TRC210A - TRC410A - TRC610A
12340 WORLD TRADE DRIVE SAN DIEGO, CA 92128
800-854-2235 CARVINAUDIO.COM

PRO1TL
PRO5TL
XLRAC
1. PLACE THE SUBWOOFERS:
Place the subwoofer on a rm, level surface where it will be used.
- If you are stacking two subwoofers, place them so the bottom feet sit into
the receptacles on top.
- When stacking two TRx3010A subs, lay them at rather than vertically.
2. INSERT POLES: Insert SS7 poles into the top hole on one TRx3903
and the top hole on the TRx3010A or center hole on the TRx3018A sub.
3. STACK: One at a time, stack the TRx3903’s onto the subwoofer using
the poles as guides.
To see a video of the setup, search
“Carvin TRC system setup” on YouTube.
SYSTEM SETUP
PRO5TL
PRO5TL
XLR
IN-OUT
AC
XLRAC
TRC200A
TRC210A,
TRC400A,
TRC410A:
TRC600A,
TRC610A:
4. Connect speaker cables.
Connect a TRx3903 speaker to the TRX3010A or TRx3018A
SATELLITE SPEAKER jack with a PRO5TL speaker cable.
- Single Subwoofer stack : Link the two TRx3903’s with a short
PRO1TL speaker cable.
- Two Subwoofer stack: Connect one TRx3903 to each
TRX3010A or TRx3018A with PRO5TL cables.
5. Connect AC power.
Connect the detachable AC cord to the AC IN jack and plug it
into an AC power outlet.
6. Connect your input signal.
Connect your mixer’s output to the XLR INPUT on the
TRx3010A or TRx3018A.
- TRC600A or TRC610A: link the rst XLR OUTPUT to the
second XLR INPUT.
7. Power On.
Turn on the Power switch.
The “Preset” screen on the Digital Display should read:
“Trx3903 External”
-Otherwise, select it from the preset screen using the
Up/Down (SET) buttons.
SYSTEM SETUP IS COMPLETE!
SS7 POLE
TRx3903
SS7 POLE
TRx3903
TRx3018A
FOOT
(RECEPTACLE)

“TRx3010A Preset” - or - “TRx3018A Preset” screen:
Select “TRx3903 External” using the Up/Down buttons pq.
This will load optimized settings for your TRC-A system to drive the TRx3903 speakers.
No further adjustment is required, however you may choose to make adjustments to the other settings below.
Press the RIGHT or LEFT buttons to access the screens for each setting.
SENSITIVITY:
1.0v, 1.2v, 1.4v, 2.0v (Vrms)
Sets the signal level required at the INPUT XLR jack to reach maximum volume. The factory setting is 1.4v.
A lower setting allows a small signal at the INPUT to produce maximum volume from the TRC-A system. A higher setting requires
a large input signal.
For example, if your mixer is not putting out enough level, change this setting to 1.2v or 1.0v. If your mixer puts out a hot signal, set
this to 2.0v.
(X-OVER:) NOTE: When using the speaker presets such as “TRx3903 External”, crossover settings are automatically set and this screen is bypassed.
When connecting TRx3903’s, the manual crossover frequency setting is not recommended.
The X-OVER setting is only available when using the “Sub Only” or “Variable X-Over” preset, used when connecting different
speakers to the TRx3010A or TRx3018A. You can refer to the TRx3010A/TRx3018A manual for more information.
POLARITY:
NORMAL or REVERSE
The standard setting is NORMAL. If low freqencies are lacking or sound unusual, try the REVERSE setting.
When subwoofers are placed at multiple locations in a room, or if the TRx3903 speakers are positioned far away from the subwoofer,
low frequencies can be negatively affected by phase cancellations. Most problems can be corrected with the REVERSE setting.
(CONTOUR EQ:)
ONLY active for the TRx3903 presets. EQ contours: Live 1, LIve 2, DJ/Playback1, DJ/Playback2
The Contour EQ setting offers four different equalization
presets specifically designed for use with TRC systems. The
preset names are based on the type of material to be played,
select which one sounds best for your music. The factory flat
setting is “Live 1”.
ENHANCE BASS: OFF, ON
The Enhance Bass feature boosts the 35-50Hz range and
extends the low frequency reponse by 15Hz without overload-
ing the system. The effect will be reduced at very high volumes
to protect the speakers, but will still deepen the bass response.
EXT. VOLUME: +6dB to -6dB (in 1db steps), -9dB, -12dB, MUTE
The External Volume setting adjusts the volume of the speakers connected to the SATELLITE SPEAKER jack, leaving the sub-
woofer level unchanged.
- Increasing the Ext. Volume raises the level coming from the TRx3903’s, which will then be louder than the TRx3018A subwoofer.
- Decreasing the Ext. Volume lowers the level coming from the TRx3903’s, allowing you to hear more of the TRx3018A subwoofer.
You may want to adjust your mixer output level or the Input Sensitivity setting after changing the Ext. Volume setting.
DSP SETTINGS
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR
CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl, sink,
laundry tub, in a wet basement, near a swimming pool, etc). Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The product should be connected to a power supply only of the type described in
the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization
is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs.
SERVICING: The user should not attempt to service the appliance beyond that described in the operating
instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to
replacement text on the unit for correct fuse type.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous volt-
age” within the product’s enclo-
sure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
This symbol is intended
to alert the user to the
presence of important
operating and maintenance
(servicing) instructions
in the literature accompanying the
appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
LIMITED WARRANTY
Your Carvin Audio loudspeaker is guaranteed against failure for 5 YEARS unless otherwise
stated. Carvin will service and supply all parts at no charge to the customer providing the unit is
under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY
FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE
IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers
or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for
damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect
use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or
implied. No representative or person is authorized to represent or assume for Carvin any liability in
connection with the sale or servicing of Carvin Audio products.
CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
MAINTAINING YOUR EQUIPMENT
Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit
can be wiped with a dry or slightly damp cloth in order to remove dust and bring back the new look.
As with all pro gear, avoid prolonged use in caustic environments (salt air). When used in such an
environment, be sure the amplifier is adequately protected.
SERVICE:
In the USA, please go to www.carvinaudio.com
under “SUPPORT” click on “REPAIR INFORMATION”
Outside the USA: contact your dealer or go to http://www.carvinaudio.com
click on “DEALERS” for your nearest service center.
Include a written description of the problem with serial number and date of purchase.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
(BYPASSED)
“X-OVER” SETTING
TRx3018A
Sensitivity: 1.4v
TRx3018A
Polarity: Normal
TRx3018A contour
EQ: Live 1
TRx3018A Preset:
TRx3903 External
TRx3018A
Enhance Bass: Off
TRx3018A
Ext. Volume: 0dB
( TRx3903 PRESETS
ONLY )
To adjust DSP settings, choose a setting screen with the LEFT and RIGHT buttons t u.
Use the UP and DOWN buttons pq to adjust the setting. Settings are automatically saved to the preset.

1. POWER SWITCH (reset)
Push the upper portion of the power switch to turn the system on. If the
blue POWER indicator is on but there is no sound or if the Protect LED
is on, check for; a) lack of INPUT signal, b) too many speakers attached
to the SATELLITE SPEAKER output, c) bad speaker cable, d) damaged
external speaker, or e) blocked fan intake. If the problem persists, reset
by turning the power off for 10 seconds and then turn it back on.
2. POWER LED
The POWER LED indicates the unit is turned on and functioning properly.
3. SIGNAL LED
The SIGNAL LED indicates there is a signal present at the INPUT XLR.
4. LIMIT LED
The LIMIT LED indicates maximum output of the system is being reached.
A flashing LIMIT LED is acceptable, the DSP will reduce peaks to prevent
amp clipping. If the LIMIT LED is continuously ON, reduce the level
going in to the INPUT XLR. You can also adjust the DSP setting for Input
Sensitivity. As with any system, reduce the volume if distortion is heard.
5. DIGITAL DISPLAY
The bright green LED DIGITAL DISPLAY will display various information
about the system and its settings. When you first turn on the unit, the
display will indicate which preset is loaded. To change settings use the
UP/DOWN pq(SET) and LEFT/RIGHT t u buttons.
6. SETTING BUTTONS: t upq (SET)
Use the UP and DOWN (SET) buttons to select “the TRx3903 External”
preset. The LEFT and RIGHT buttons will allow editing of more advanced
settings, which are explained in the DSP SETTINGS section of this manual.
There are only a few settings to select from.
7. INPUT/THRU XLR CONNECTORS
Connect the INPUT XLR to a signal source such as the output of a mixer.
The THRU XLR can be connected to more TRx3018A’s or other units.
8. REMOTE LEVEL (MUTE) CONNECTOR
This is a terminal block connector with 5 volt control of volume, typically
used in permanent installations. Short the CTL and GND pins to MUTE.
9. USB PORT
The USB port is for updating system firmware such as additional presets
for Carvin Audio speakers including the SATELLITE SPEAKER output.
10. PROTECT LED
The PROTECT LED indicates one of the protection circuits has activated
and no sound will be heard from the amp. To reset the amp, turn the
power off for about 10 seconds, then turn it back ON. If the PROTECT
LED stays lit for more than 5 seconds, check your SATELLITE SPEAKER
cable connnections, speaker impedance or a blocked fan intake.
11. SATELLITE SPEAKER OUTPUT
The SATELLITE SPEAKER output is a Twist-Lock connector for power-
ing external speakers. Presets for several Carvin Audio speakers are pre-
programmed. For TRC-A systems, choose the “TRX3903 External” preset
on the display. Manual settings are available for other speakers. Speakers
can be chained together so long as the total impedance does not go below
4 ohms (two TRx3903’s). If you go below the minimum speaker load, the
amp may shut off or the red PROTECT LED may light. To reset the protection
circuit, turn off the POWER switch and connect the recommended load.
12. FAN INTAKE / EXHAUST VENTS
The TRx3010A/TRx3018A power module features a variable speed fan,
which runs silent at low speeds. Make sure the fan intake and exhaust
vents are free from blockage at all times.
13. AC IN / AC OUT POWER JACKS & FUSE
Be sure to plug into the proper voltage using AC IN jack. A detachable
locking power cord is supplied (for European 230V use a CEE-7 plug cord
set). Plug the cord into a grounded 3 prong power source. No attempt
should ever be made to use the amp without the ground connected.
The AC OUT connector can be used to power one TRx/3010A/TRx3018A,
a powered speaker, or any device(s) with a total of 10A rating or less.
The FUSE is located internally near the AC input. To check or replace,
first remove the power cord and then remove the amp module from the
speaker enclosure and remove the front panel to access the fuse. The
fuse type is a 250V Slow Blow rated at 15A.
A locking AC cord (Carvin part# 120V16L7, 120V model) is supplied
with the amp. However, a standard AC cord can be used. To detach the
cord from the amp, press the release lever on the underside of the cord
near the amp.
7
PRESS TO
RELEASE
LOCKING AC CORD
120V16L7
813 91011
TRx3010A, TRx3018A SYSTEM CONTROL PANEL
641 3212 5
TRC-A SYSTEMS 042616
This manual suits for next models
6
Other CARVIN Speakers System manuals

CARVIN
CARVIN 1584 V1 User manual

CARVIN
CARVIN 1283 User manual

CARVIN
CARVIN TRx Series User manual

CARVIN
CARVIN 832-V1 User manual

CARVIN
CARVIN SCx1112 User manual

CARVIN
CARVIN RL410T User manual

CARVIN
CARVIN RL115 User manual

CARVIN
CARVIN 1584 User manual

CARVIN
CARVIN 822 User manual

CARVIN
CARVIN 742-742P-V1 User manual
Popular Speakers System manuals by other brands

Cambridge Sound Works
Cambridge Sound Works FourPointSurround FPS1800 user guide

Hybrid+
Hybrid+ L6A user manual

Cambridge Sound Works
Cambridge Sound Works Ensemble III Installation and operating instructions

Klip Xtreme
Klip Xtreme MagBlaster Pro manual

Speed Link
Speed Link Proteus SL-8102 user guide

Speed Link
Speed Link Daimos SL-8105 user guide