CARVIN TRx Series User manual

TRx3210 Line Array
Turnkey Systems
User Manual
c
Made in USA
76-03210D 091212

2
TRx3210 Line Array
Table of Contents:
Introduction .............................................................3
Unpacking ................................................................3
Concept.....................................................................3
Specications............................................................4
e Line Array Eect - ...........................................5
Pure Path Horn Lens and MF/LF Drivers
Safety - Stacking and Flying..................................6
Ground Stacking...................................................... 7
SureFly™ Rigging
- Assembling an Array...................................... 8-11
- T-Bar Hang Points ..............................................12
- Transportation.....................................................13
Amplication & Wiring
- Biamp....................................................................14
- Pin Flip/Mode Switch.........................................15
- Full Range Passive...............................................16
- Processing and tuning.................................. 17-19
Amp Rack Packages ..............................................20
Accessories .............................................................21
Warranty .................................................................21
System Packages .............................................. 22-23

3
Introduction:
Congratulations on purchasing a TRX3000 Series loudspeaker from Carvin Professional Audio Products. e
TRx Series are designed to give you the best in audio quality and many years of reliable, trouble-free operation.
It oers excellent pattern control, simple ground stacking design as well as easy over-head suspension with
safe and practical rigging hardware, superior audio quality, full technical documentation, and the backing of a
world-class company with over 66 years of manufacturing experience and technology including a comprehen-
sive warranty. Please read through this user manual carefully before you attempt to operate the loudspeaker
system. It contains valuable information which will enable you to easily and quickly connect the loudspeakers
along with important system set-ups, stacking and ying instructions.
Thank You
ere are many options in the market place today for loudspeaker products and we thank you for choosing
Carvin Professional Audio Products for your loudspeaker choice.
Carvin professional audio products are proudly engineered and manufactured in San Diego, California, USA!
If you would like additional information about this or any other Carvin product, please contact us. Complete
and detailed product information is available on our web site.
Unpacking
Upon unpacking the unit, please check carefully for damage. If damage has occurred, please notify the delivery
service at once. You, the consignee, must handle any claim. Please retain packaging in case of future re-shipment.
TRx Line Array Concepts
Pulling from our TCS Audio engineering, Carvin has produced a modular line array loudspeaker system that
is very adaptable to almost any performance venue. Not every scenario requires a own PA system. So with
that in mind, the TRx3210 Line array loudspeaker can easily be stacked or own.
A new loudspeaker system can be an expensive investment. With the TRx3210 system, Carvin oers an ex-
treme value allowing an aordable solution.
800.854.2235 carvinproaudio.com
USA contact: Tony Mirador
Office: 800.403.4484 x114
[email protected]
International contact: Joel Kiesel
Office: 760.522.5676
[email protected]
12340 World Trade Dr., San Diego, CA 92128
c

4
Side of TRx3210
with and without
SureFly hardware
Frequency Response
TRx3210 Rear Plate Block Diagram in Full Range Mode
Dimensions
HIGH PASS
FILTER
MID / LOW
PASS FILTER
LOW PASS
FILTER
EQ AND
MATCHING
1+
1-
2+
2-
+
-
SPEAKER
GUARD
1+
1-
2+
2-
+
-
+
-
MID / LOW
DRIVER
LOW
DRIVER
HORN DRIVERS
+
-
600mm
[23,50in] 575mm
[22,63in]
375mm
[14,75in]
285mm
[11,25in]
600mm
[23,50in]
SureFly Hardware
Four TRx3210’s
Stacked on TRx1121
Ten TRx3210 hang with 4
straight and 6 set at 5 degrees
No hardware
needed. Feet fit into
cabinet below
Side of TRx3210
with and without
SureFly hardware
Frequency Response
TRx3210 Rear Plate
Block Diagram in Full Range Mode
Dimensions
HIGH PASS
FILTER
MID / LOW
PASS FILTER
LOW PASS
FILTER
EQ AND
MATCHING
1+
1-
2+
2-
+
-
SPEAKER
GUARD
1+
1-
2+
2-
+
-
+
-
MID / LOW
DRIVER
LOW
DRIVER
HORN DRIVERS
+
-
600mm
[23,50in] 575mm
[22,63in]
375mm
[14,75in]
285mm
[11,25in]
600mm
[23,50in]
SureFly Hardware
Four TRx3210’s
Stacked on TRx1121
Ten TRx3210 hang with 4
straight and 6 set at 5 degrees
No hardware
needed. Feet fit into
cabinet below
TRx3210 Specifications
TRx3210F - with SureFly™ hardware pre-installed
System Type: Dual 10-inch 3-Way, Reflex
Frequency Response: 70 Hz – 18.5 kHz (-10DB)
85 Hz – 16 kHz (-3 dB)
Coverage Pattern: 100˚ H x 10˚ V (single enclosure)
Crossover: 3-Way Quasi
Speaker Guard™ HF protection
Crossover Frequencies: 500Hz & 1.5 k Hz
Sensitivity (1w @ 1m): 98dB
Maximum SPL: 131dB Peak single enclosure
137dB Peak four enclosures
140dB Peak eight enclosures
LF Driver: 2x 10-inch 2-inch VC
HF Driver: 2x 1-inch exit 1.75-inch VC
Nominal Impedances (Continuous/Program/Peak)
Full range: 8 ohms 500w /1000w /2000w
Bi-amp LF: 8 ohms 500w /1000w /2000w
Bi-amp HF: 8 ohms 120w /240w /480w
Enclosure: 13-Ply Russian Baltic Birch
Suspension/Mounting: 14 captive 3/8in-16 nut fly pts.
Two 1-3/8 pole mount cups
Finish: Black DuraTec™
UV, water resistant IP2
Transport: 2 Recessed Handles
Grill: Black powder coated steel
Acoustically Transparent Foam Backing
Connectors: Two 4-pin TwistLoc connectors
Dimensions (H x W x D): 11.8 in x 23.5 in x 14.75 in
300 mm x 600 mm x 374 mm
Net Wt: 52 lb (24 kg) without hardware
Maximum Fly Capacity: 16
Made in USA
See pages 14-16 for full range - pin ip mode and
bi-amp conguration
4-pin TwistLoc

5
The PurePath™ Horn Lens and dual 10” Drivers
e PurePath™ Horn Lens is a one-of-a-kind design. is horn lens is CNC machined in-house from acoustically
non-resonant Eastern Maple hardwood, providing a very smooth, equal path length wave guide for pure, natural
and cylindrically projected highs. e two HF Mylar compression drivers feature a 1-inch exit and a 1.75” voice
coil. e PurePath™ Horn Lens places the HF drivers in proper phase alignment with the 10-inch drivers.
PurePath Horn Lens
dual 10” 250w drivers
IP2 UV & Water Resistant
Two 10-inch MF/LF drivers feature 2-inch voice coils and power handling of 250w per driver. ey are treated
for IP2 UV approval, which is water resistant. ese drivers are front loaded and eld replaceable. e front
steel grills are foam backed for added protection from the elements and are easily removed for service access.
The Line Array Effect
The line-array effect is achieved by the 0 degree coupling of the
enclosures in the array. The inherent advantage of a line array
design allows the rear audience to hear nearly the same levels as
the front. The PurePath™ horn produces a tight 10 degree vertical
x 100 degree horizontal pattern on a single cabinet. Conventional
enclosures drop 6dB when doubling the distance to the listener.
However, when coupled in a line array this pattern narrows fur-
ther to produce the line array effect, which drops only 3dB when
doubling the distance to the listener. This effect is also present with
the tight coupling of the 10-inch drivers in an 11.8-inch vertical box.
When the straight line of the line array is broken as in the case of
a “J” curve, the elements curved at the bottom of the array behave
more as a “point source” loudspeaker producing normal output to
the closer listeners.
The TRx3210 can be deployed in a full curvilinear array at 12.5
degrees of angle between elements. This produces a smooth “point
source” array covering 50 degrees of vertical and 100 degrees of
horizontal coverage with only four enclosures.
Line Array with
J curve Linear Curve
Array

6
Stacking and Flying
Overview
To take full advantage of the extremely exible properties of the TRx3210 system, two modes of rigging systems have been developed.
e rst mode utilizes the interlocking feet and pole mounts and the second mode is using the optional SureFly™ hardware. e two rig-
ging systems allow either line arrays or virtual point source clusters to be assembled – intuitively, quickly and easily, and with an absolute
minimum of additional external parts to suit the coverage requirements of a huge variety of professional sound reinforcement situations.
e second mode using the optional SureFly™ hardware is inherently safe, exible, self-contained and simple to use. e load is taken
entirely through the SureFly™ hardware and not through the cabinet’s woodwork. e rigging design allows the creation of clusters and
arrays that can be assembled quickly and with a minimum number of crew, and with full control of the vertical angles between enclosures
and the overall cluster inclination.
Safety Notes on Rigging - Important Please Read!
e Carvin SureFly™ rigging system has been designed and constructed to a high standard of safety and tested to the most demanding
conditions. As a very rst concern and in order to ensure the highest safety standards, the information following on the assembly and safe
use of rigging accessories must be carefully understood and followed. Every user that operates, suspends, or lis a TRx3210 loudspeaker
system needs to be properly trained before ever constructing and deploying the system in a working situation.
Only use Carvin recommended rigging accessories, which are specically designed for their intended purpose. Do not use Carvin Sure-
Fly™ rigging with other types or brands of loudspeakers. is practice may compromise safety standards and Carvin will not be respon-
sible for damage or injury as a result.
Do not modify the rigging accessories, or use them in any other way than described in this user manual. Rigging components supplied
as part of a complete assembly are non-interchangeable and must not be exchanged with the component parts of any other assembly.
e component parts of Carvin SureFly™ rigging accessory must only be assembled using the fasteners and methods of assembly rec-
ommended in this manual. e use of fasteners and methods of assembly not specied or approved by Carvin may result in an unsafe
rigging assembly. Welding, or any other means of permanently xing rigging components to each other or to cabinet xing points, is not
recommended.
Rigging assemblies must only be assembled using the appropriate parts and xings as specied in this manual using the specic mount-
ing instructions. Rigging components or assemblies must only be xed to Carvin loudspeaker cabinets using the cabinet xing points,
assembly methods and fasteners specied in this manual and the specic mounting instructions.
Walls, oors or ceilings must be capable of safely and securely supporting the actual load.
e rigging accessory used must be safely and securely xed both to the loudspeaker and to the wall, oor or ceiling.
When mounting rigging components on walls, oors or ceilings ensure that all xings and fasteners used are of an appropriate size and
load rating. Wall and ceiling claddings, and the construction and composition of walls and ceilings, all need to be taken into account
when determining whether a particular xing arrangement can be safely employed for a particular load. Cavity plugs or other specialist
xings, if required, must be of an appropriate type and must be tted and used in accordance with the makers instructions. Use only the
rigging accessory xing holes indicated in this manual and the specic mounting instructions to x Carvin SureFly™ rigging accessories
to walls, oors or ceilings.
Where specied, the recommended maximum torque settings for screw fasteners must be strictly complied with.
Secondary Safeties
Best practice dictates in addition to the principle load bearing means of suspension, that all loudspeakers own in theaters, studios or
other places of work and entertainment should (and where local laws apply), be provided with an independent, properly rated and se-
curely attached secondary means of safety. Only steel wire ropes or steel chains of an approved construction and load rating may be used
as secondary safeties. Plastic covered steel wire ropes are not permitted for use as secondary safeties.
Safety Inspections
Carefully inspect rigging systems components and cabinets for defects or signs of damage before proceeding to assemble a own array.
If any parts are damaged or suspect, DO NOT USE THEM.
Regular and more rigorous test and inspection of rigging components must also be carried out. Safety legislation, and test and inspection
requirements, will vary from country to country. In most cases, annual independent test and inspection by a suitably approved and qual-
ied inspector will be required. Users must ensure compliance with all applicable safety requirements. Carvin recommends regular safety
inspections and further recommends that a logbook be kept detailing the test and inspection history of each Carvin rigging Component.
Always wear protective head-wear, footwear and eye protection in accordance with local regulations. Anyone involved in ying ANY
sound system, especially in a touring capacity, should take note of the following advice:
“ e rigging of a own sound system may be dangerous unless undertaken by qualied personnel with the required
experience and certication to perform the necessary tasks. Fixing of hanging points in a roof should always be carried
out by a professional rigging specialist and in accordance with the local rules of the venue. e house rigger and/or
building manager must always be consulted.”

7
Stacking Array without hardware
Each TRx3210 features durable feet and align to interlock without the need for additional hardware. is is
ideal for stacking on top of a ground-stacked subwoofer or elevated using two SS4 poles.
Stacking with hardware
e SureFly™ hardware can also be utilized for ground stacking. e
SureFly™ T-bar can be used as a base for a ground stacked array.

8
Assembling an Array
Assembly and deployment of TRx3210 arrays are carried out one array module at a time or in pre assembled
groups of array modules. Aer installing the SureFly™ hardware kit to each enclosure, attach the T-bar to the top
array enclosure. e TRx3210F comes with preinstalled SureFlyTRx hardware. Each subsequent enclosure can be
pinned at dierent angles to accomplish wide vertical coverage angles and focus sound energy where needed.
1.
2.
2.
2.
1.
1.
1.
2.
2.
2.
1.
1.
2.
1.
1.
Step 2
Installing the T-Bar
Attach assembled T-Bar to rst (top) array enclosure.
At the same time lower side plates of the T-Bar
evenly into the SureFly hardware. Attach the T-Bar
side plates using the bolts, washers and nuts supplied.
Using a torque wrench, tighten the bolts to 40 lbs.
e T-bar side plates must insert between the two
plates of the array module hardware. Align holes and
secure with the included four (2 per side) quick re-
lease pins into both (A) and (B) holes.
Step 1 (skip with TRX3210F preinstalled hardware)
Installing the SureFlyTRx rigging kit.
Each enclosure will require one SureFlyTRx rigging kit. e kit in-
cludes all mounting hardware and quick release pins. Drilling into
the TRx3210 enclosure is not required. All mounting points on the
TRx3210 enclosure have threaded inserts.
Set all quick release pins aside. As shown in the diagrams, assemble
the side panels of the SureFlyTRx kit using the included bolts and
washers. Insert the adjustment plate in-between the two mounting
plates. e lower bolt will function as a hinge. Hand tighten the bolts
and insert the quick release pins as shown. Once the side plates are
aligned by installing the Quick Release Pins into the positions shown,
use a torque wrench to tighten the bolts to 20. lbs. Repeat this pro-
ceedure on the other side of the enclosure. Aer the SureFlyTRx
hardware has been installed on all enclosures, they may be stacked
4 high by making sure both side adjustment plates slide in-between
the mounting plates of the enclosure below. Store pins in the handle
area aer installation.
Tighten bolts to 20 ft lbs
Tighten bolts to 40 ft lbs

9
Step 3
Installing the Shackle
Attach rated 5/8” shackle to lug # 4. Note:
this position sets a basic starting point for a
straight vertical hang.
GROUND
Attach to motor hoist
GROUND
Straight Vertical Hang
Shackle
Lug #4
1 2 3
GROUND
Attach to motor hoist
GROUND
Straight Vertical Hang
Shackle
Lug #4
1 2 3
Step 4
Adding additional enclosures
Attach a rated chain motor or hoist hook to the
shackle. Using the chain motor or hoist, li as-
sembly up to clear another array module. Place
an array module underneath the rst array
module assembly and lower suspended array
module. As you are lowering, align so feet mate
with foot receptacles on top of lower array mod-
ule. Side adjustment plates must insert between
the two plates of the array module hardware.
See Step 5 for adjustment plate.
5/8” Shackle
# TCSHK58
Finger tighten
shackle only.
Do not use a
tool to tighten
Quick Release Pin
Press the button on the top of the pin with thumb to
insert and remove pin.

10
Step 5
Remove the lower quick-release pin from the han-
dle storage location to release the adjustment plate.
Allow the adjustment plate to swing down between
the two side plates on the lower enclosure. Adjust
enclosures to allow adjustment plate to capture the
lower enclosure with hook on adjustment plate.
When the adjustment plate is fully in place, the “A”
location pin can be inserted. Repeat on opposite
side of array enclosure.
Step 6
Push the second quick-release pin into forward
hole labeled (A 0˚) on the upper enclosure. Repeat
on opposite side of array enclosure. This 0 degree
position is used for a straight Line-Array. This is
also storage and transport position when using the
DB3210 dolly board.
e quick-release pins
can be stored in the
handles on the inside
of the SureFly hardware
plates on each side of
the array module. is
keeps them from being
misplaced or damaged
during transport and
holds the inner adjust-
ment plate from swing-
ing down.
Pin Storage
GROUND
Attach to motor hoist
A
d
j
u
s
t
m
e
n
t
p
l
a
t
e
s
w
i
n
g
s
d
o
w
n
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
Adjustment plate
hook captures
lower enclosure
close up view

11
Step 6 continued
If you require a J curve at the bottom of a long array or a curve array, adjust the pins on the lower enclosures to
create the desired curve. There are 6 different angles that can be achieved between each enclosure by changing
both pin positions. With the lower enclosure in the “A” position, the upper enclosure’s pin positions/angles are:
0, 2.5, 5 degrees. When adjusting angle pin, lower the front of the bottom cabinet to the desired angle.
0 degree Pin position 2.5 degree Pin position 5 degree Pin position
7.5 degree Pin position 10 degree Pin position 12.5 degree Pin position
With the lower cabinet in the “B” position the upper enclosure’s angle pin positions/angles are: 7.5, 10, 12.5
degrees. Caution when adjusting pin “A” or “B”. Support the weight of the lower enclosure. Do not adjust pin
“A” or “B” with additional enclosures attached below. This pin locks the adjustment plate to the lower enclosure.

12
T-Bar Hang Points
To change the angle of the array, attach the shackle to the dierent lug holes as shown in the below diagram. e
further back from center, a larger degree of forward tilt is achieved.
By using two hang points and two chain motor hoists, the angle of the array can be changed by raising or low-
ering the front or back of the array by adjusting the chain motors. is requires the use of a second shackle as
shown in the diagram below.
8˚
12˚16˚20˚
8˚
1-POINT
HANG
(4 CABS)
2-POINT
HANG
0˚
23˚26˚29˚
8˚
12˚16˚20˚
8˚
1-POINT
HANG
(4 CABS)
2-POINT
HANG
0˚
23˚26˚29˚
To chain
motor hoist To chain
motor hoist
To chain
motor hoist

13
DB3210 Transport Dolly Board (optional)
e optional Baltic Birch/Duratec™ DB3210 transport Dolly Board allows a block of up to four TRx3210 speaker
cabinets to be conveniently transported in a pre-rigged conguration and is recommended as the most ecient
way to truck and handle the cabinets. e transport dolly board is wide enough to allow the lock pins to be in-
serted in the SureFly™ hardware while on the dolly board, which makes it possible to li the block of four cabinets
together while still being dimensioned to t up to ve-across for a standard truck pack.
strap slots

14
Full Range or Bi-Amp Configuration
Trx3210 Enclosures can be congured either in full range/passive mode or bi-amped 3-way mode. ey ship
from the factory as standard in full range/passive mode. Selecting from one to the other is as simples as ipping
a concealed switch on the connection panel.
OUTPUT
INPUT
THRU INPUT INPUT THRU
GND PARALLELLIMITERBRIDGE
LIFT
ONLY
BRIDGE
12
OUTPUT
INPUT
THRU INPUT INPUT THRU
GND PARALLELLIMITERBRIDGE
LIFT
ONLY
BRIDGE
12
OUTPUT
INPUT
THRU INPUT INPUT THRU
GND PARALLELLIMITERBRIDGE
LIFT
ONLY
BRIDGE
1 2
BIAMP
BIAMP
NORM
NORM
(NORMAL, BIAMP)
(NORMAL, BIAMP)
LOW
FREQ
AMP
MID
FREQ
AMP
HI
FREQ
AMP
DCM3800L
DCM3800L
DCM2000L
CARVIN XD360 OUTPUTS
HI
FREQ
MID
FREQ
LOW
FREQ
AD45 ADAPTER
(1+,1-) to (2+,2-) for HI FREQ.
and
(1+,1-) to (1+,1-) for MID FREQ.
Bi Amp Operation:
Remove rubber plug marked Full Range/ BiAMP from con-
nection panel. Using a small at-head screw driver, carefully
insert screwdriver into opening and slide switch to the right
for Bi-Amp operation. Note: Mode switch must always be
in the UP (normal) position for Bi-Amp operation. Replace
rubber plug aer change.
Bi-Amp Hook-up
not required with DCMLx amps
SUB

15
Pin Flip Switch
Carvin TRx3210 loudspeakers come with a speaker pin ip switch. In full range/passive mode, this switch
allows the user to select operation from either pins 1+ & 1- (standard) or pins 2+ & 2-. is can signicantly
simplify speaker cable runs by half with 4-pin TwistLoc cables. Below are a few examples of how the pin ip
switch is used.
Remove rubber plug marked NORMAL/ PIN FLIP from connection panel. Using a small at-head screw driv-
er, carefully insert screwdriver into opening and slide switch to the down position for Pin Flip operation. is
will enable use of pin 2+ & 2- to drive this speaker module. Note: pins 1+ & 1- will be no longer used in this
cabinet. Replace rubber plug aer change.
OUTPUT
INPUT
THRU INPUT INPUT THRU
GND PARALLELLIMITERBRIDGE
LIFT
ONLY
BRIDGE
12
DCM3800L
AMP CH.2: PINS 2+, 2-
(PIN FLIP, FULL RANGE)
AMP CH.2: PINS 2+, 2-
(PIN FLIP, FULL RANGE)
AMP CH.1: PINS 1+, 1-
NL4
SP4
NL4
AD45 ADAPTER
(1+,1-) + (1+,1-)
to (1+,1- , 2+,2-)
OLDER MODELS USE ADAPTER AD45
(before SEPT. 2012)
CH.1 (1+,1-)
and
CH.2 (2+,2-)
Full-Range Passive Hook-up in Pin Flip Mode

16
OUTPUT
INPUT
THRU INPUT INPUT THRU
GND PARALLELLIMITERBRIDGE
LIFT
ONLY
BRIDGE
12
DCM3800L
AMP CH.2: PINS 2+, 2-
(PIN FLIP, FULLRANGE)
AMP CH.1: PINS 1+, 1-
(NORMAL, FULL RANGE)
AMP CH.2: PINS 2+, 2-
(PIN FLIP, FULLRANGE)
AMP CH.1: PINS 1+, 1-
(NORMAL, FULL RANGE)
AD45 ADAPTER
(1+,1-) + (1+,1-)
to (1+,1- , 2+,2-)
OLDER MODELS USE ADAPTER AD45
(before SEPT. 2012)
CH.1 (1+,1-)
and
CH.2 (2+,2-)
Full-Range Passive Hook-up 2 normal Pin Mode, 2 Pin Flip Mode

17
Processor Settings for XD360, DCMLx or other speaker management systems
For optimum performance, a loudspeaker management processor is recommended. Carvin oers both an out-
board processor such as the XD360 X-Drive™ as well as the DCMLx power amps that have on-board X-Drive™
processing. Carvin’s XD360 and DCMLx power amps will have the TRx3210 crossover settings as a preset. e
following charts provide a variety of settings that cover both full-range and bi-amping. e below settings apply
to all speaker management systems.
LEFT TWO ON SUB RIGHT TWO ON SUB
OUTPUT Main (ch1) N/A (ch2) SUB (ch3) Main (ch1) N/A (ch5) SUB (ch6)
Output Gain -3dB 0.0 dB -3dB 0.0 dB
Input Source A A, A+B or B B, A+B or
(Alt Source) (C for Aux sub) (A for 8 mono) (C for Aux
sub)
Polarity OUT IN OUT IN
LPF frequency 20 KHz 80Hz 20 KHz 80Hz
LPF type OUT Linkwtz 24 OUT Linkwtz 24
HPF frequency 80 Hz 32 Hz 80 Hz 32 Hz
HPF type Linkwtz 24 Butter 18 Linkwtz 24 Butter 18
Limit Threshold 0dB 0dB 0dB 0dB
Output Delay
PEQ1 GAIN 6 dB 6 dB
PEQ1 FREQ 630 Hz 630 Hz
PEQ1 BW 0.16 0.16
PEQ2 GAIN -9 dB -9 dB
PEQ2 FREQ 2.7 KHz 2.7 KHz
PEQ2 BW 0.12 0.12
LEFT FOUR RIGHT FOUR
OUTPUT HI (ch1) LO-MID (ch2) SUB (ch3) HI (ch4) LO-MID (ch5) SUB (ch6)
Output Gain -15 dB 0.0 dB 0.0 dB -15 dB 0.0 dB 0.0 dB
Input Source A A A, A+B or B B B, A+B or
(Alt Source) (C for Aux sub) (A for 8 mono) (C for Aux sub)
Polarity OUT IN IN OUT IN IN
LPF frequency 20kHz 1.5kHz 80Hz 20kHz 1.5kHz 80Hz
LPF type OUT Butter 48 Linkwtz 24 OUT Butter 48 Linkwtz 24
HPF frequency 1.5 KHz 80 Hz 32 Hz 1.5 KHz 80 Hz 32 Hz
HPF type Butter 48 Linkwtz 24 Butter 18 Butter 48 Linkwtz 24 Butter 18
Limit Threshold -3 0 0 -3 0 0
Output Delay 84 uS 0.0 mS 0.0 mS 84 uS 0.0 mS 0.0 mS
PEQ1 GAIN -6 dB -9dB -6 dB -9dB
PEQ1 FREQ 2 KHz 315 Hz 2 KHz 315 Hz
PEQ1 BW 1 0.3 1 0.3
PEQ2 GAIN 12 dB 12 dB
PEQ2 FREQ 12 KHz 12 KHz
PEQ2 BW 3 3
Stereo passive 2 array modules pole mounted on sub
STEREO Bi Amp 4 array modules 2.5 - 12.5 degrees Curve array

18
LEFT (OR UPPER) FOUR RIGHT (OR LOWER) FOUR
OUTPUT Main (ch1) not used (ch2) SUB (ch3) Main (ch3) not used (ch5) SUB (ch6)
Output Gain 0 0.0 dB 0 0.0 dB
Input Source A A, A+B or B B, A+B or
(Alt Source) (C for Aux sub) (A for 8 mono) (C for Aux sub)
Polarity OUT IN OUT IN
LPF frequency 20 KHz 80Hz 20 KHz 80Hz
LPF type OUT Linkwtz 24 OUT Linkwtz 24
HPF frequency 80 Hz 32 Hz 80 Hz 32 Hz
HPF type Linkwtz 24 Butter 18 Linkwtz 24 Butter 18
Limit Threshold 0dB 0dB 0dB 0dB
Output Delay
PEQ1 GAIN 6 dB 6 dB
PEQ1 FREQ 630 Hz 630 Hz
PEQ1 BW 0.16 0.16
PEQ2 GAIN -9 dB -9 dB
PEQ2 FREQ 2.7 KHz 2.7 KHz
PEQ2 BW 0.12 0.12
Stereo passive 4 array modules 2.5 - 12.5 degree Curve array
Also works for 8 module passive mono hang using right as upper and left as lower.
4 enclosure Curve Array

19
UPPER FOUR LOWER FOUR (“J curve settings)
OUTPUT HI (ch1) LO-MID (ch2) SUB (ch3) HI (ch4) LO-MID (ch5) SUB (ch6)
Output Gain
-9 dB 0.0 dB -9 dB (-15db) 0.0 dB 0.0 dB
Input Source
A A not used A A A
(Alt Source)
(C for Aux sub)
Polarity
OUT IN OUT IN IN
20kHz 1.5kHz 20kHz 1.5kHz 80Hz
LPF frequency
OUT Butter 48 OUT Butter 48 Linkwtz 24
LPF type
1.5 KHz 80 Hz 1.5 KHz 80 Hz 32 Hz
HPF frequency
Butter 48 Linkwtz 24 Butter 48 Linkwtz 24 Butter 18
HPF type
-3 0 -3 0 0
Limit Threshold
84 uS 0.0 mS 84 uS 0.0 mS 0.0 mS
Output Delay
-6 dB 9 dB -6 dB 9 dB (0db)
PEQ1 GAIN
2 KHz 400 Hz 2 KHz 400 Hz
PEQ1 FREQ
1 0.12 1 0.12
PEQ1 BW
12 dB 12 dB (-9dB)
PEQ2 GAIN
12 KHz 12 KHz (315 Hz)
PEQ2 FREQ
3 3 (0.3)
PEQ2 BW
0.12 0.12
Bi Amp 8 array modules straight hang
Lower four cabinets can be adjusted for “J” curve see settings.
8 enclosure Line Array

20
Turnkey Factory Assembled Amp Racks
AR-MAIN
(1)DCM2004L
(2)DCM3800L
(1)XD360
(1)IP340
(1)USB-CBL
(8)C3XLR
(1)1U Panel
(1)4U Vented Panel
(1)AC3PH120*
AR-S
(4)DCM3800L (bridged)
(1)IP340
(1)USB-CBL
(4)C3XLR
(1)4U Vented Panel
(1)AC3PH120*
*Delete Option Available
SUB Amp Rack (15,200 Watts)
Main Amp Rack (6,600 Watts)
AR AMP RACKS
DCM-L AMPS & XD360 Processor
AR-MAIN
(1)DCM2004L
(2)DCM3800L
(1)XD360
(1)IP340
(1)USB-CBL
(8)C3XLR
(1)1U Panel
(1)4U Vented Panel
(1)AC3PH120*
AR-S
(4)DCM3800L (bridged)
(1)IP340
(1)USB-CBL
(4)C3XLR
(1)4U Vented Panel
(1)AC3PH120*
*Delete Option Available
SUB Amp Rack (15,200 Watts)
Main Amp Rack (6,600 Watts)
AR AMP RACKS
DCM-L AMPS & XD360 Processor
SUB Amp Rack (15,200 Watts)
Main Amp Rack (6,600 Watts)
ARX AMP RACKS
DCM-LX DSP AMPS (No XD360 required)
ARX-S
(4)DCM3800LX (bridged)
(1)IP340
(1)USB-HUB
(4)USB-CBL
(4)C3XLR
(1)4U Vented Panel
(1) AR1 Amp Rack
(1) ASSM-AR
(1)AC3PH120*
* Delete Option Available
ARX-MAIN
(1)DCM2004LX
(2)DCM3800LX
(1)IP340
(1)USB-HUB
(3)USB-CBL
(4)C3XLR
(1)2U Panel
(1)4U Vented Panel
(1) AR1 Amp Rack
(1) ASSM-AR
(1)AC3PH120*
SUB Amp Rack (15,200 Watts)
Main Amp Rack (6,600 Watts)
ARX AMP RACKS
DCM-LX DSP AMPS (No XD360 required)
ARX-S
(4)DCM3800LX (bridged)
(1)IP340
(1)USB-HUB
(4)USB-CBL
(4)C3XLR
(1)4U Vented Panel
(1) AR1 Amp Rack
(1) ASSM-AR
(1)AC3PH120*
* Delete Option Available
ARX-MAIN
(1)DCM2004LX
(2)DCM3800LX
(1)IP340
(1)USB-HUB
(3)USB-CBL
(4)C3XLR
(1)2U Panel
(1)4U Vented Panel
(1) AR1 Amp Rack
(1) ASSM-AR
(1)AC3PH120*
• IP340 2U Interconnect XLR inputs and TwistLoc outputs • Fast and easy connections to rack gear
• Built-in rear TwistLoc cables connect to power amps • Front USB to computer, rear to USB hub
• AC3PH120 2U AC power panel for 100-130VAC 50-60Hz • Saftey approvals ETL listed to UL standards.
• Designed for safe connections to the rack gear & house power. For use in other countries with approved adapters.
• 3 phase 120VAC/208VAC • Each phase (leg) supports one 20 amp breaker (3rd & 4th breaker on leg 3)
USB12HUB
12 port hub
To power ampsTo power amps
ARP-MAIN-BI (Biamp)
(1) DCM2004L†
(2) DCM3800L
(1) XD360 Processor
(1) IP340 Connect Panel
(1) C2U USB 2ft cable
(8) C3XLR 3ft cable
(1) 1U Blank Panel
(1) 4U Vented Panel
(1) AR1 Shock Rack Case
(1) AR-ASSM Assembled Rack
(1) AR-PROG Program / Test
(1) AC3PH120 AC Panel*
*AR-MAIN-BI without AC3PH120
*†AR-MAIN (passive) without DCM2004L
& AC3PH120
ARPx-MAIN-BI (Biamp)
(1) DCM2004Lx†
(2) DCM3800Lx
(1) IP340 Connect Panel
(1) USB12HUB
(3) C2U USB 2ft cable
(4) C3XLR 3ft cable
(1) 2U Blank Panel
(1) 4U Vented Panel
(1) AR1 Shock Rack Case
(1) AR-ASSM Assembled Rack
(1) AR-PROG Program / Test
(1) AC3PH120 AC Panel*
*ARx-MAIN-BI without AC3PH120
*†ARx-MAIN (passive) without DCM2004Lx
& AC3PH120
ARP-S (Sub)
(4) DCM3800L (bridged)
(1) IP340 Connect Panel
(1) C2U USB 2ft cable
(4) C3XLR 3ft cable
(1) 4U Vented Panel
(1) AR1 Shock Rack Case
(1) AR-ASSM Assembled Rack
(1) AR-PROG Program / Test
(1) AC3PH120 AC Panel*
*AR-S without AC3PH120
ARPx-S (Sub)
(4) DCM3800Lx (bridged)
(1) IP340 Connect Panel
(1) USB12HUB
(4) C2U USB 2ft cable
(4) C3XLR 3ft cable
(1) 4U Vented Panel
(1) AR1 Shock Rack Case
(1) AR-ASSM Assembled Rack
(1) AR-PROG Program / Test
(1) AC3PH120 AC Panel*
*ARx-SUB without AC3PH120
AR AMP RACKS
DCM-L Amps & XD360 Processor
Configured for minimum of 4 ohm operation per amplifier channel.
ARx AMP RACKS
DCM-Lx DSP Amps (XD360 not required)
Configured for minimum of 4 ohm operation per amplifier channel.
ARP-MAIN-BI Amp Rack (6,600 Watts) ARPx-MAIN-BI Amp Rack (6,600 Watts)
AR-S Sub Amp Rack (15,200 Watts) ARX-S Sub Amp Rack (15,200 Watts)
TOP VIEW
AUX IN 3 IN 2 IN 1
IP340 XLR Rear
Rear Rear
Rear Rear
Front Front
Front Front
MADE IN USA
MADE IN USA