Casio 3163 User manual

Operation Guide 3163
1
MA0904-EA
About This Manual
•Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
•Button operations are indicated using the letters shown
in the illustration.
•Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference”section.
General Guide
•Press Cto change from mode to mode.
•In any mode, press Lto illuminate the display for about one second.
•Whenever there are too many characters to fit within the upper or lower display area,
the characters will scroll automatically from right to left.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
•You can select from among four different date (day of the week, year, month, day)
formats for the upper and lower parts of the display.
•The calendar format for the upper display area depends on the currently selected
display format for the lower display area. Pressing Bwill cycle through the available
calendar formats as described below.
Example: Tuesday, June 30, 2009
When the date format (lower display
area) is one of these settings:
Pressing
B
will cycle the calendar format
(upper display area) between these settings:
MMM.DD (JUN.30)
DDD ’YY (TUE ’09) →’YY DDD (’09 TUE) →
DDD (TUE) →YYYY (2009)
DD.MMM (30.JUN)
MM-DD (06-30)
DD-MM (30-06)
DDD DD (TUE 30) MMM ’YY (JUN ’09) →’YY MMM (’09 JUN) →
MMM (JUN) →YYYY (2009)
DD DDD (30 TUE)
Pressing Din the Timekeeping Mode switches to the Custom Memo (1 and 2)
screen.
9EAR$AYOFWEEK
4IMEKEEPING3CREEN #USTOM-EMO #USTOM-EMO
0RESS
(OUR-INUTES3ECONDS
Important!
•Be sure to select your Home City (the site where you normally will use the watch)
and configure its current time and date settings before using the functions of this
watch.
To set the time and date
3ECONDS
1. In the Timekeeping Mode, hold down Auntil the
seconds start to flash, which indicates the setting
screen.
2. Press Cto move the flashing in the sequence shown
below to select other settings.
3ECONDS $34 #ITY#ODE (OUR -INUTES
$AY -ONTH 9EAR
(OUR&ORMAT#ONTRAST!DJUSTMENT
#ALENDAR&LASH!LERT&ONT
3. When the setting you want to change is flashing, use Dand Bto change it as
described below.
Screen To do this: Do this:
Reset the seconds to 00
Press D.
Toggle between Daylight Saving Time (ON)
and Standard Time (OFF)
Change the city code Use D(east) and B(west).
Change the hour or minutes Use D(+) and B(–).
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping Press D.
Change the year Use D(+) and B(–).
Change the month or day
Change the calendar display.* Use Dand B.
Configure the Flash Alert setting See “Flash Alert”.
Change the font.** Use Dand B.
Adjust display contrast See “Contrast Adjustment”.
* The following shows the available calendar display settings.
Example: Tuesday, June 30, 2009
MMM.DD (JUN.30)
DD.MMM (30.JUN)
MM-DD (06-30)
DD-MM (30-06)
DDD DD (TUE 30)
DD DDD (30 TUE)
** The following shows the available font settings.
: Bold
: Narrow
•See “Daylight Saving Time (DST)”for details about the DST setting.
4. Press Ato exit the setting screen.
•Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
•The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
$34INDICATOR
1. In the Timekeeping Mode, hold down Auntil the
seconds start to flash, which indicates the setting
screen.
2. Press Cto display the DST setting screen.
3. Press Dto toggle between Daylight Saving Time (ON
displayed) and Standard Time (OFF displayed).
4. Press Ato exit the setting screen.
•The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
0RESS
4IMEKEEPING-ODE 3TOPWATCH-ODE#OUNTDOWN4IMER-ODE !LARM-ODE7ORLD4IME-ODE
4)-% 7/2,$ 4)-%2 34/07 !,!2-

Operation Guide 3163
2
Custom Memo
Custom Memo lets you input and store two memos, each containing up to 14
characters.
In the Timekeeping Mode, press Dto cycle between the screens shown below.
#USTOM-EMO #USTOM-EMO
4IMEKEEPING-ODE
•The following are the characters you can input for a Custom Memo.
0-9 A-Z - ( ) @ : ; . ! ? / \ ^ #
•The display can show up to seven characters of memo text at one time. If there are
more than seven characters, the text will scroll from right to left once when you press
Dto display the memo. To scroll the text while Custom Memo 1 or Custom Memo 2
is displayed, press B.
To input memo text
#USTOM-EMO
1. In the Timekeeping Mode, use Dto select Custom
Memo 1 or Custom Memo 2.
2. Hold down Afor about two seconds until the first
character of the memo starts to flash.
•This is the input screen.
3. Use D(+) and B(–) to scroll through input characters
at the current flashing position.
4. When the character you want is displayed at the
flashing position, press Cto move the flashing to the
next position to the right.
5. Repeat steps 3 and 4 to input all of the characters you
want.
•To delete all currently input text, press Dand Bat
the same time.
•Pressing Cwhile the flashing is located at the last
(14th) character will cause it to move back to the first
character.
6. When the memo text is the way you want, press A.
•This exits the input screen.
World Time
7ORLD4IME
7ORLD4IME#ITYCODE
54#
$IFFERENTIAL
-ONTHn$AY
World Time shows the current time in 31 cities (31 time
zones) around the world.
•All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time for another city code
In the World Time Mode, press Dto scroll eastward
through city codes or Bto scroll westward.
•For full information about city codes, see the “City Code
Table”.
•If the current time for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make necessary changes.
•You can change your Home City code in the
Timekeeping Mode. For more information, see “To set
the time and date”.
To toggle a city code time between Standard Time and Daylight Saving Time
$34INDICATOR
1. In the World Time Mode, use Dand Bto display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down Afor about two seconds to toggle between
Daylight Saving Time (DST displayed) and Standard
Time (DST not displayed).
•The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•Note that the Standard Time/Daylight Saving Time
setting affects only the currently displayed city code.
Other city codes are not affected.
•Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
Countdown Timer
(OURS-INUTES3ECONDS
You can set the countdown timer within a range of
one second to 24 hours. An alarm sounds when the
countdown reaches zero.
•All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing C.
Timer Types
There are three different settings that you can use in order to configure the timer as
describe below.
Timer Types Screen When the end of the countdown is reached
One-time Timer CD-STOP
The original start time appears on the display and
the countdown stops. This type of timer is best
when you normally need to start the countdown
from the same start time.
Countdown/Count Up
Timer CD-UP
An alert sounds and the watch starts an elapsed
time measurement operation. The elapsed time
operation is performed at one-second increments
for up to 24 hours.
Auto Repeat Timer CD-RPT The timer automatically restarts a new countdown
from the same the start time.
Timer Start Time
You can use one of the watch’s preset start times or you can set your own start time,
if you want.
•Preset Start Times: You can select any one of the following fixed preset start times.
1 minute, 3 minutes, 5 minutes, 10 minutes, 15 minutes, 30
minutes, 45 minutes, 1 hour
•Custom Timer: You can set the start time you want.
Timer Alarms
The watch beeps for about 10 seconds when the end of a countdown is reached.
Pressing any button while the beeper is sounding stops it.
Setting the Timer
Using a preset timer: Display the screen for the preset start time you want and select
the timer type.
Using a Custom Timer: Display the Custom Timer screen, set the start time and select
the timer type.
1. In the Countdown Timer Mode, press Bto scroll through the start times and
display a preset start time or the Custom Timer screen.
Each press of Bscrolls through the start time screens as shown below.
0RESS
0RESET3TART4IME #USTOM4IMER
MINUTE HOUR
#USTOM4IMER
     
4IMERTYPE
2. Hold down Ato display the setting screen.
•If you displayed a preset start time, holding down
Awill cause the timer type to flash. Advance to “To
select the timer type”in step 3.
•If you displayed the Custom Timer, holding down
Awill cause the hour digit of the start time to flash.
Advance to step 3.
4IMERSTARTTIMEHOURS
3. Press Cto move the flashing to the setting you want to
change.
•Each press of Cmoves the flashing between the
settings as shown below.
(OURS -INUTES
4IMERTYPE 3ECONDS
To set the start time hours, minutes, and seconds
Use D(+) and B(–) to change the currently flashing
setting.
•The start time can be set in 1-second increments up to
24 hours.
•To configure a start time of 24 hours, set the start time
as 0:00:00.
To select the timer type
4IMERTYPE
Use Dto cycle thorugh the timer type settings as shown
below.
CD-STOP: One-time Timer
CD-UP: Countdown/Count Up Timer
CD-RPT: Auto Repeat Timer

Operation Guide 3163
3
To use the countdown timer
1. In the Countdown Timer Mode, press Bto scroll through the start times and
display a preset start time or the Custom Timer screen.
Each press of Bscrolls through the start time screens as shown below.
0RESS
0RESET3TART4IME #USTOM4IMER
MINUTE HOUR
#USTOM4IMER
     
2. Press Dto start the countdown of the timer you selected in step 1.
•The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•Press Dwhile a countdown operation is in progress to
pause it. Press Dagain to resume the countdown.
•To stop a countdown operation completely, first pause
it (by pressing D), and then press B. This returns the
countdown time to its starting value.
•With the Countdown/Count Up Timer, an alert sounds
and the watch starts an elapsed time measurement
operation when the end of the countdown is reached.
Pressing Dwill stop the elapsed time measurement
operation. Pressing Bwhile elapsed timing is stopped
will reset the timer to its start time.
Stopwatch
$AY
SECOND
(OURS-INUTES3ECONDS
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•The display range of the stopwatch is 99 days, 23 hours,
59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
%LAPSED4IME
3PLIT4IME
4WO&INISHES
3TOP 2ESTART 3TOP #LEAR
3TART
3TART 3PLIT
30,DISPLAYED
3PLITRELEASE 3TOP #LEAR
3TART 3PLIT 3TOP 3PLITRELEASE #LEAR
&IRSTRUNNER
FINISHES
$ISPLAYTIMEOF
FIRSTRUNNER
3ECONDRUNNER
FINISHES
$ISPLAYTIMEOF
SECONDRUNNER
Alarms
!LARMTIME
(OUR-INUTES
Your watch has five independent multi-function alarms.
You can set the hour and minute for the alarm time, and
you can select one of four repeat patterns (week day,
weekend, daily, one-time). One of the alarms is a snooze
alarm.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour. You can
specify the Hourly Time Signal repeat pattern, and a start
time and end time.
•There are five alarm screens, each of which shows an
alarm name: ALARM1 to ALARM4, and SNOOZE. The
Hourly Time Signal is indicated by SIGNAL.
•When you enter the Alarm Mode, the data you were
viewing when you last exited the mode appears first.
•All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use Dto scroll through the alarm
screens until the one whose settings you want to
configure is displayed.
•Select alarm screen ALARM1 through ALARM4 to
configure a normal alarm. Select the SNOOZE alarm
screen to configure the snooze alarm.
•The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down Auntil the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
•This operation turns on the alarm automatically.
3. Press Cto move the flashing in the sequence shown below to select other
settings.
(OUR -INUTES 2EPEAT0ATTERN
4. While a setting is flashing, use D(+) and B(–) to change it.
•You can select any one of the four alarm repeat patterns described below.
To configure the alarm to sound: Select this setting:
Daily DAILY
Once on the specified date only ONCE
Daily on Saturday and Sunday WEEKEND
Daily from Monday through Friday WEEKDAY
5. Press Ato exit the setting screen.
•With the 12-hour format, set the time correctly as a.m. or p.m.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
•Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
•To stop the alarm tone after it starts to sound, press any button.
•When Flash Alert is turned on, the red and green LEDs at the bottom of the display
will flash in time with the alarm beeper.
•Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm Mode setting screen
To test the alarm
In the Alarm Mode, hold down Dto sound the alarm.
To turn an alarm on and off
3NOOZEALARMINDICATOR
!LARMONINDICATOR
/N/FFSTATUS
1. In the Alarm Mode, use Dto select an alarm.
2. Press Bto toggle it on (on) and off (––displayed).
•Turning on an alarm (ALARM1 to ALARM4, or
SNOOZE) displays the alarm on indicator on its Alarm
Mode screen.
•In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
•The alarm on indicator flashes while the alarm is
sounding.
•The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
To configure Hourly Time Signal settings
%NDTIME3TARTTIME
1. In the Alarm Mode, use Dto display the Hourly Time
Signal (SIGNAL) screen.
•Hourly Time Signal times are displayed using the
24-hour time format.
2. Hold down Auntil the Hourly Time Signal start time
starts to flash. This is the setting screen.
•This also will turn on the Hourly Time Signal.
3. Press Cto move the flashing in the sequence shown
below to select other settings.
3TART4IME %ND4IME 2EPEAT0ATTERN
4. While a setting is flashing, use D(+) and B(–) to change it.
•When the start time and end time settings specify a period that is 24 hours long
(such as a start time of 7:00 a.m. and an end time of 6:00 a.m.), is displayed.
•If you set the same time for both the start time and end time (a single hourly time
signal), only the start time will be displayed on the Hourly Time Signal screen.
(Example: 8:00)
•You can select any one of the three Hourly Time Signal repeat patterns described
below.
To configure the Hourly Time Signal to sound: Select this setting:
Daily DAILY
Daily on Saturday and Sunday WEEKEND
Daily from Monday through Friday WEEKDAY
5. Press Ato exit the setting screen.
•With the 12-hour format, set the time correctly as a.m. or p.m.(P).
To turn the Hourly Time Signal on or off
(OURLYTIMESIGNAL
ONINDICATOR
1. In the Alarm Mode, use Dto display the Hourly Time
Signal (SIGNAL) screen.
2. Press Bto toggle the Hourly Time Signal on
((Check mark displayed.)) and off (
(Check mark not displayed.)).
•An Hourly Time Signal on indicator is on the Alarm Mode
Hourly Time Signal screen while the Hourly Time Signal
is on.
•The Hourly Time Signal on indicator is on the display in
all modes while the Hourly Time Signal is turned on.

Operation Guide 3163
4
Illumination
!UTOLIGHTSWITCH
INDICATOR
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch for reading
towards your face.
•The auto light switch must be enabled (indicated by the
auto light switch indicator) for it to operate.
•See “Illumination Precautions”for more important
information.
To illuminate the display manually
In any mode, press Lto turn on illumination for about
one second.
•The above operation turns on illumination regardless of
the current auto light switch setting.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
•Wear the watch on the outside of your wrist.
Parallel to ground More than 40°
Warning!
•Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged
in any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
•When you are wearing the watch, make sure that its auto light switch is
disabled before riding a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To enable and disable the auto light switch
In the Timekeeping Mode, hold down Lfor about three seconds to toggle the auto
light switch between enabled (auto light switch indicator displayed) and disabled (auto
light switch indicator not displayed).
•The auto light switch indicator is on the display in all modes while the auto light
switch is enabled.
•In order to protect against running down the battery, the auto light switch is disabled
automatically approximately six hours after you enable it.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display cycles automatically through the screens of
each mode.
To turn off Auto Display
Press Aor C.
To turn on Auto Display
In the Timekeeping Mode, hold down Band Dfor about
two seconds.
•Note that Auto Display cannot be turned on while a
setting screen is on the display.
Flash Alert
When Flash Alert is on, the LED under the display will
flash in time with the countdown alarm, alarms, and the
Hourly Time Signal.
To turn Flash Alert on and off
1. In the Timekeeping Mode, hold down Auntil the
seconds start to flash, which indicates the setting
screen.
2. Press Cten times to display the Flash Alert setting
screen.
3. Press Dto toggle Flash Alert on (SYNCHRO displayed) and off (OFF displayed).
4. Press Ato exit the setting screen.
•The Flash Alert setting you select with the above procedure is applied in all modes.
•You also can use the above procedure to check the current Flash Alert on/off setting.
Contrast Adjustment
You can adjust the contrast of the watch to make its display figures darker or lighter.
To adjust contrast
1. In the Timekeeping Mode, hold down Auntil the seconds start to flash, which
indicates the setting screen.
2. Press C12 times to display the contrast adjustment (CONT) screen.
3. Use D(+) and B(–) to scroll through the available display format numbers
(1 through 7).
4. Press Ato exit the setting screen.
Button Operation Tone
The button operation tone sounds any time you press one of the watch’s buttons. You
can turn the button operation tone on or off as desired.
•Even if you turn off the button operation tone, the alarms, the Hourly Time Signal,
and the countdown alarm all operate normally.
To turn the button operation tone on and off
-UTEINDICATOR
In any mode (except when a setting screen is on the
display), hold down Cto toggle the button operation tone
on (mute indicator not displayed) and off (mute indicator
displayed).
•Holding down Cto turn the button operation tone on or
off also causes the watch’s current mode to change.
•The mute indicator is displayed in all modes when the
button operation tone is turned off. The LED light will
flash when you change modes.
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes without
performing any operation, the watch exits the setting screen automatically.
Scrolling
The Band Dbuttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the Stopwatch, Alarm or World Time Mode, the data you were viewing
when you last exited the mode appears first.
Timekeeping
•The year can be set in the range of 2000 to 2099.
•The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
World Time
•All World Time Mode times are calculated from the current Home City time in the
Timekeeping Mode using UTC time differential values.
•The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
•The UTC differential is a value that indicates the time difference between a reference
point in Greenwich, England and the time zone where a city is located.
•The letters “UTC”is the abbreviation for “Coordinated Universal Time”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds.
Leap seconds are added or subtracted as necessary to keep UTC in sync with the
Earth’s rotation.
Illumination Precautions
•The electro-luminescent panel that provides illumination loses power after very long
use.
•Illumination may be hard to see when viewed under direct sunlight.
•The watch may emit an audible sound whenever the display is illuminated. This
is due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
•Illumination turns off automatically whenever an alarm sounds.
•Frequent use of illumination runs down the battery.
Auto light switch precautions
•Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, disable the auto light switch feature.
•Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
•Illumination turns off in about one second, even if you
keep the watch pointed towards your face.
•Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If illumination
does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it
back towards you again. If this does not work, drop your
arm all the way down so it hangs at your side, and then
bring it back up again.
•Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
•You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.

Operation Guide 3163
5
Specifications
Accuracy at normal temperature: ±15 seconds a month
Timekeeping: Hour, minutes, seconds, a.m./p.m., year, month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 31 city codes); Daylight Saving
Time (summer time)/Standard Time
Custom Memo: 14 characters × 2
World Time: 31 cities (31 time zones)
Other: Daylight Saving Time/Standard Time
Countdown Timer
Setting unit: 1 second
Countdown unit: 1 second
Countdown range: 24 hours
Selection of One-time Timer, Countdown/Count Up Timer, or Auto Repeat Timer
Stopwatch
Measuring unit: 1/100 second
Measuring capacity: 99 days, 23:59'59.99''
Measuring modes: Elapsed Time, Split Times, Two Finishes
Alarm
5 multi-function* alarms: four one-time alarms; one snooze alarm
* Four patterns (daily, once, weekend, weekday)
Hourly Time Signal*
* Start and stop time specification. Three patterns (daily, weekend, weekday)
Illumination: EL (electro-luminescent panel); Auto Light Switch
Other: Button operation tone on/off; Flash alert; Auto Display
Battery: One lithium battery (Type: CR2025)Approximately 5 years on type CR2025 (10
seconds of alarm operation per day, 1.5 seconds of illumination per day)
City Code Table
City Code City UTC Offset/
GMT Differential
PPG Pago Pago –11
HNL Honolulu –10
ANC Anchorage –9
LAX Los Angeles –8
DEN Denver –7
CHI Chicago –6
NYC New York –5
SCL Santiago –4
YYT St. Johns –3.5
RIO Rio De Janeiro –3
FEN Fernando de Noronha –2
RAI Praia –1
UTC 0
LON London
PAR Paris +1
CAI Cairo +2
JED Jeddah +3
THR Tehran +3.5
DXB Dubai +4
KBL Kabul +4.5
KHI Karachi +5
DEL Delhi +5.5
KTM Kathmandu +5.75
DAC Dhaka +6
RGN Yan
g
on +6.5
BKK Ban
g
kok +7
HKG Hong Kong +8
TYO Tokyo +9
ADL Adelaide +9.5
SYD Sydney +10
NOU Noumea +11
WLG Wellington +12
•Based on data as of March 2008.
•The rules governing global times (UTC offset and GMT differential) and summer time are determined by
each individual country.