Catler JS 8011 User manual

SLOW JUICER
JS 8011
Instruction Manual
SLOW JUICER
Návod kobsluze
ŠNEKOVÝ ODŠŤAVŇOVAČ
Návod na obsluhu
ZÁVITOVKOVÝ ODŠŤAVOVAČ
Használati útmutató
CSIGÁS GYÜMÖLCSPRÉS
Instrukcja obsługi
WYCISKARKA ŚLIMAKOWA
  


SLOW JUICER

1
CONTENTS
CONTENT
3 Catler recommends safety rst
10 Know your juicer JS 8011
12 Operating your juicer ES 8011
12 Before rst use
12 Assembling your juicer
13 Operating your juicer
16 Reverse operation
16 Overheating protection
16 Processing fruit and vegetables
18 Care and cleaning
20 Troubleshooting

2CONGRATULATIONS
Congratulations
for buying your new juicer JS 8011

3
CATLER RECOMMENDS SAFETY FIRST
CATLER RECOMMENDS SAFETY FIRST
We understand the importance of safety and that’swhy we put your safety rst from the
initial design concept to the production itself. Nevertheless, please be careful and follow the
instructions below when using this juicer.
• This appliance may be used by children 8 years
of age and older and by persons with physical
or mental impairments or by inexperienced
persons, if they are properly supervised or
have been informed about how to use of the
product in asafe manner and understand the
potential dangers.
• Children must not play with the appliance.
• Cleaning and maintenance performed by the
user must not be performed by unsupervised
children.
• If the power cord is damaged, ask the
authorised service for areplacement in order
to prevent hazards. It is forbidden to use the
appliance if it has adamaged power cord.
WARNING:
INCORRECT USE MAY RESULT IN
INJURY.
• When handling the press screw, be take care to
avoid injury with the screw edge.

4CATLER RECOMMENDS SAFETY FIRST
• Do not use the appliance if the rotation strainer
is damaged.
• Always turn o the juicer and disconnect it
from the power socket if you will not be using
it and if you are leaving it without supervision,
before assembly, disassembly or cleaning.
• This appliance is not to be used by children.
Keep this appliance and its power cord out of
children.
• The appliances may be used by persons
with physical or mental impairments or by
inexperienced persons only if they are properly
supervised or have been informed about how
to use of the product in asafe manner and
understand the potential dangers.
• Wash the juice and pulp jugs, press tube, press
screw, strainers and the chamber’sinterior in
warm water with asmall amount of washing-
up liquid. Rinse and wipe dry. Always follow the
instructions in the “Care and cleaning”chapter.
• Before replacing the strainer, always rst turn
the appliance o by pressing the STOP button,
unplug the power cord from the mains socket
await until all moving parts have stopped.
• This juicer is designed for home use. It is not

5
CATLER RECOMMENDS SAFETY FIRST
intended for use in premises such as:
– sta kitchens in stores, oces and other
workplaces;
– agricultural farms;
– hotel or motel rooms andother living areas;
– bed and breakfast establishments.
• Before rst use, remove all advertising labels /
stickers from the juicer.
• To prevent any risk of suocation of children,
please store all plastic bags out of their reach or
dispose of them safely.
• Use the juicer on an even, dry and stable
surface. Do not place on the kitchen or table
countertop edge, sink dish rack etc. Do not
place it on / in the vicinity of electric or gas
cooker or other appliances generating heat.
• Do not use the juicer in vehicles, boats or
outdoors or for purposes other than it was
designed for.
• Before connecting the juicer to apower
socket, make sure the voltage stated on the
product'srating label corresponds to the
voltage in your power socket. Connect power
cord only to aproperly grounded socket.

6CATLER RECOMMENDS SAFETY FIRST
• Make sure that the juicer is correctly assembled
before putting it into operation. Only use
the original accessories supplied by the
manufacturer.
• The juicer is equipped with asafe start lock.
This means it cannot be started unless properly
assembled.
• Before juicing, please remove hard kernels from
fruits and vegetables contained for example in
peaches, apricots, mango etc. and also remove
uneatable peels for example from oranges,
pineapples, melons, mandarins etc. You needn’t
remove seeds from berries and kiwi.
• Do not insert excessively hard raw materials
in the juicer, such as sugar cane or ingredients
such as pepper, coee beans or hard pits
contained for example in apricots, peaches,
mango etc. Otherwise, damage to the juicer or
injury might occur.
• The juicer can be used to press fresh garlic or
pepper, however, it’snot designed to grind
dried spice.
• Thanks to the vertically positioned press
screw, there is almost no need to push the
raw materials through the feed tube. Most

7
CATLER RECOMMENDS SAFETY FIRST
raw materials are pulled by the screw into the
juicing mechanism. If you need to push some
raw materials through the feed tube such as
apples, please always use the supplied pusher.
• Never push the raw materials with your ngers
or other tools such as kitchen utensils etc.
• If the raw materials get stuck inside the juicing
mechanism, please press the reverse run
button and hold it down until the raw materials
are released.
• The maximum continuous operating time is
30seconds. Then allow the juicer to cool down
for 20 minutes.
• Disconnect the juicer from the power socket
by gently pulling the plug, not the power cord.
Otherwise, damage to the cord or the mains
socket might occur.
• Before disassembling the parts that are in
motion during use, please make sure that the
juicer is turned o and unplugged from the
mains socket and wait until these parts have
stopped completely.
• Please follow the instruction is the "Cleaning
and maintenance”chapter.

8CATLER RECOMMENDS SAFETY FIRST
• Never wash the motor unit and its connection
cable under running water or submerge it in
water or another liquid.
IMPORTANT SAFETY INSTRUCTIONS FOR
USING ELECTRICAL EQUIPMENT
• Fully unwind the power cord before use.
• Do not leave the power cord hanging over the
edge of atable or countertop or allow it to
touch ahot surface or to become tangled up.
Do not put heavy objects on the power cord.
• For safety reasons, we recommend to connect
the appliance in an independent electrical
circuit separated from other appliances.
Donot use adapter plugs or extension cords to
connect the appliance to apower outlet.
• To prevent electric shock, do not submerge this
appliance, its base or power cord in water or
any other liquid.
• We recommend that you inspect the appliance
regularly. Do not use the appliance if it is
damaged in any way or if the power cord or
plug is defective. All repairs or adjustments
must be performed at the nearest Catler
authorised service centre.

9
CATLER RECOMMENDS SAFETY FIRST
• Any maintenance other than standard cleaning
must be performed at authorised Catler service
centre.
• We recommend to install aresidual current
device (standard safety switches in your power
outlet) to provide ahigher level of protection
when using the appliance. We recommend to
install aresidual current device (with anominal
residual operating current of no more than
30mA) in the electric circuit in which your
appliance is to be connected. For further expert
advise, please contact your electrician.

10 KNOW YOUR JUICER JS 8011
KNOW YOUR NEW JUICER JS 8011
17
16
567
4
8
9
10
11
13
12
14
15

11
KNOW YOUR JUICER JS 8011
JUICER DESCRIPTION
1. Feed tube
2. Feed opening
3. Feed opening protective cover
4. Press screw
5. Fine strainer
6. Coarse strainer
7. Strainer for ice cream/sorbet preparation
8. Juice chamber
9. Pulp outlet
10. Juice spout with acloseable anti-drip tap
11. Control panel
12. Shaft
13. Motor base
14. Power cable
15. Plunger
16. Cleaning brush
17. Juice jug
18. Juice jug lid
19. Pulp container
CONTROL PANEL DESCRIPTION
1
2
34
5
6
1. Hard button to process hard fruit and vegetables
2. Soft button to process soft fruit and vegetables
3. Sorbet button to make ice cream / sorbet
4. Vegetable drink button
5. Reverse button - reverse run
6. Stop button - to stop the processing

12 OPERATING YOUR JUICER ES 8011
OPERATING YOUR JUICER JS 8011
BEFORE FIRST USE
Before rst use, remove all packaging
and advertising labels / stickers from the
appliance.
Check the appliance and all the accessories
for damage. Never use adamaged appliance
and/or appliance with damaged accessories,
damaged power cord or plug.
Wipe the motor base with asoft sponge
slightly moistened in warm water. Then wipe
dry with aclean cloth.
Before rst use, wash all removable
accessories designed to contact with food in
warm water with asmall amount of washing-
up liquid. Rinse and wipe dry. Follow the
instructions in the “Care and Cleaning“
section.
WARNING!
Be very careful
when handling the
press screw to avoid
injury on the edge.
ASSEMBLING YOUR JUICER
Before assembling your juicer, please make
sure that the silicone sealing at the chamber
bottom is rmly inserted in the pulp outlet.
If the seal was inserted or located incorrectly,
the pulp or juice could drain through the
outlet.
Before assembling the juicer, also make sure
that the silicone sealing is correctly inserted
in the chamber centre. The seal’swider part
must point upwards.

13
OPERATING YOUR JUICER ES 8011
1. Put the motor base on aclean, dry and
at surface far enough from the mains
socket.
2. Insert the chamber on the motor base so
that jags on the motor base engage with
the notches at the chamber bottom.
3. Insert the strainer in the chamber. Each
strainer has indentation at the bottom
which must t in the chamber bottom
indentation to make sure the strainer is
properly xed in the chamber.
Please select appropriate strainer
depending on the type of the selected
fruit and vegetables:
- Ane strainer is suitable for
processing hard fruit and raw
vegetables.
- Acoarse strainer is suitable for
processing soft fruit or vegetables.
- An ultra-ne strainer is suitable for
processing fruit or vegetables to
prepare ice creams or sorbets.
NOTE
If you are about to juice both hard and
soft fruit or vegetables (such as apples
and bananas), put either the ne
strainer (juice making without pulp) or
the coarse strainer (juice making with
pulp ala smoothie) in the chamber.
4. Insert the press screw onto the shaft.
Rotate the screw as needed to make sure
that it’sinserted correctly.
5. Now insert the feed tube so that the
arrow on the chamber is aligned with the
open lock mark on the tube.
6. Rotate the tube clockwise until the arrow
on the tube is aligned with the open lock
mark. Correct tube locking is indicated by
clicking.
NOTE
Do not use force when inserting the
feed tube. If the feed tube cannot be
inserted, check if the press screw is
installed correctly.
WARNING!
The juicer
won’t start
unless correctly
assembled.
7. Put the pulp container under the pulp
outlet and put the juice container under
the juice spout.
8. The juicer is now ready for use.
OPERATING YOUR JUICER
Before plugging the power cord in the mains
socket and turning the juicer on, please make
sure that juicer is correctly assembled.
The juicer is equipped with two safety
devices that prevent it from being started
after plugging the power cord:
- the feed tube is not installed correctly;
- the feed opening’sprotective lid is open.
1. Insert the mains cord plug into apower
socket.
2. The control panel will light and the juicer
is ready for use.

14 OPERATING YOUR JUICER ES 8011
NOTE
As soon as the juicer is started, you can
open the protective cover and insert
bigger pieces of fruit or vegetables.
Opening the protective cover
will interrupt the juicer operation
automatically and an acoustic signal
will be heard. To restore the juicer
operation, close the protective cover.
3. Press the selected program’sbutton to
start the juicer.
PROGRAM TABLE
/
Juicing hard / soft
fruit or vegetables
Insert cleaned and washed pieces of fruit or vegetables one
by one into the feed opening. Use the provided pusher.
Preparing sorbet
from frozen fruit or
vegetables.
Insert pieces of frozen fruit or vegetables slowly and wait
until each piece is processed. To prepare sorbets, use the
pulp coming out of the pulp outlet.
Vegetable drink The program is suitable for preparing vegetable drink. Close
the juice spout. Process the prepared vegetables. You may
enrich your vegetable drink by nuts and seeds that should
be immersed in water before processing. If your are about to
process more than 450ml of drink, open the outlet regularly
to prevent overowing.
NOTE
Do not use ice cubes to make ice
cream / sorbet. Always use the ice
cream / sorbet strainer and the sorbet
program. To make fruit and vegetable
sorbet, use only frozen pieces of fruit
and vegetables. Never process other
raw materials.
Attention:
If you are about to process nuts or
seeds using the“Vegetable Drink”
program, always soak the nuts or
seeds before processing.
. If needed, use the supplied pusher to
push the fruit and vegetable pieces
through the feed opening.

15
OPERATING YOUR JUICER ES 8011
WARNING!
Never use your
fingers, spoons
or other utensils
to push fruit or
vegetable pieces
through the feed
opening. Always
use the supplied
pusher.
5. The juice is owing into the chamber
and the pulp is owing into the pulp
container through the outlet while the
juicing is in progress.
6. The juice spout is equipped with
acloseable tap so you can let the juice
ow into container or jar or you can close
the tap so that the juice gathers in the
chamber. This is suitable for processing
various types of fruit and vegetables.
In this way, the juice becomes stirred.
As soon as the juice contents amount
reaches 450ml, it’snecessary to open the
spout and pour the juice into aprepared
juice jug or jar.
NOTE
If large amounts of froth form during
the juicing, we recommend to leave
the spout open.
7. If the juice jug or jar becomes full while
the juicing is in progress, close the spout
and put another jug or jar underneath.
8. When the juicing process is nished,
press STOP and wait until the juicer
comes to afull standstill. Unplug the
power cord from the mains socket.
Thejuice may be discharging even
awhile after the juicer is turned o. Wait
for the juice to discharge. Then clean the
juicer according to the instructions in the
“Care and cleaning”chapter.
9. We recommend to consume the juice
immediately after it’sbeen made.
WARNING!
If the juicer is to
be turned on with
no load, do not
operate it longer
than 1 minute.
Do not use the
juicer longer than
20 minutes in
continuous motor
operation.
To prevent
overflowing, make
sure that the juice
in the chamber
does not exceed
amaximum volume
of 450ml.

16 OPERATING YOUR JUICER ES 8011
REVERSE RUN
The juicer is equipped with areverse run to
allow you to remove the stuck raw materials
from around the press screw. To enable the
reverse run, press Reverse.
1. Hold down Reverse.
2. The juicer run will be interrupted
automatically.
3. After about 3 seconds, the screw begins
to rotate in areverse direction compared
ti juicing, thus releasing the stuck raw
materials.
4. It’snecessary that the Reverse button
be held down all the time the reverse
run is in progress until the stuck raw
materials are released.
5. Release the pressed Reverse button
and press aselected program button
to continue with the raw material
processing.
6. If the raw materials are still stuck, repeat
the procedure above or turn the juicer
o, unplug the power cord from the
mains socket and disassemble the juicer
to remove the stuck raw materials.
NOTE
To enable the reverse run feature,
you needn’t turn the juicer o by
pressing the STOP button. The
juicer operation will be interrupted
automatically by pressing Reverse.
OVERHEATING PROTECTION
The juicer is equipped with asafety system
which protects it from overheating. If the
motor runs continuously for more than
20 minutes, the system will be enabled
automatically to turn the juicer o. In such
case, please unplug the power cord from
the mains socket and allow the juicer to cool
down for about 20 minutes. Then plug it again
in the mains to continue with using the juicer.
PREPARING FRUIT AND
VEGETABLES
1. Insert the pieces of fruit and vegetables
in the feed opening one by one to avoid
overheating the juicer.
2. Cut the fruit and vegetables to equally
sized pieces.
3. In order to increase the juice amount,
insert fruit and vegetable pieces with
ahigh juice content (such as apples or
pears) in turns with those with alow juice
content (such as bananas).
4. When processing fruit and vegetables
with ahigher seed content (such as
grapevine) or ahigher pulp content
(such as celery), it will be necessary to
disassemble and clean the juicer to
ensure eciency for further processing.
5. Before juicing, please remove hard pits,
seeds etc. from fruit and vegetables.
Donot process fruit and vegetables
which are too hard. There is arisk of
damage to the juicer.
6. Do not insert fruit which has been soaked
in wine, honey or sugar.
7. Do not insert food with ahigh oil content
(such as olives, ax seeds etc.).
8. Not not insert pulp for further juicing.
HARD FRUIT AND VEGETABLES (HARD
PROGRAM)
If your are about to process hard fruit or
vegetables (such as carrot, apples or ginger)
using the Hard program, please wash
the fruit or vegetables carefully and remove
uneatable parts. We recommend to soak such
fruit or vegetables in water for afew minutes
before processing. Cut the fruit or vegetables
to equally sized pieces as needed. In order to
get as much juice as possible select the fruit
or vegetables with amore juice content.

17
OPERATING YOUR JUICER ES 8011
SOFT FRUIT AND VEGETABLES (SOFT
PROGRAM )
If you are about to process soft fruit or
vegetables (tomatoes, berries, oranges) using
the Soft program, please wash the fruit or
vegetables carefully and remove uneatable
parts. Cut the fruit or vegetables to equally
sized pieces as needed.
FRUIT, VEGETABLES AND SEEDS (SOFT
PROGRAM)
If you are about to process fruit, vegetables
and seeds (such as raisins, pomegranate,
passionower etc.) using the Soft program,
please wash the fruit or vegetables carefully
and remove uneatable parts. Please use
edible part only for juicing. Before processing
raisins, we recommend to pit them so that
their taste cannot aect the nal juice taste.
FIBRE RICH FRUIT AND VEGETABLES
(HARD PROGRAM)
If you are about to process fruit and
vegetables rich in bre or leaf vegetables
(such as celery, pineapple etc.) using the
Hard program, please wash the fruit or
vegetables carefully and remove uneatable
parts. We recommend that fruit or vegetable
stalks (such as ribbed celery or rhubarb)
are processed one by one. It’suseful to
disassemble leaf vegetables (such as lettuce)
or cabbage and roll individual leaves before
processing.
It’suseful to supplement celery juice with
juice from fruit and vegetables without
ahigh share of bre.
It’snecessary that pineapple, mango etc. be
peeled properly before processing.
HERBS
If you are about to process herbs (such as
parsley, spring onion), always insert the ne
strainer and select the Hard program .
You may also avour your fruit or vegetable
juice with aherb processed with fruit or
vegetables without changing the strainer.
SORBET PREPARATION
(SORBET PROGRAM)
With the Sorbet program, use only frozen
fruit or vegetables that were washed, cleaned
or peeled and freed from uneatable parts,
cubed and frozen beforehand. It’simportant
for the frozen fruit or vegetables to be
removed from the freezer at least 20 minutes
before processing.
VEGETABLE DRINK PROGRAM
You can use nuts and seeds for making cold
vegetable juices. Soak nuts and seeds in
cold water for at least 4 hours (or overnight)
before processing. Before processing, you
can also remove the peel which may aect
the nal juice’staste.
You can use the processing residues of nuts
and seeds for making desserts (such as bundt
cakes) or cookies.

18 CARE AND CLEANING
CARE AND CLEANING
Before cleaning the appliance, always make
sure that the juicer has been stopped. Then
unplug the power cord from the mains
socket and let it cool down properly.
It’simportant that the juicer be cleaned
immediately after each use to prevent the
food residues from drying in the juicer
interior. Regular maintenance will prolong
the lifetime of your juicer.
To clean the juicer and its accessories, never
use abrasive cleaning agents, thinners, petrol
or similar substances.
WARNING!
DO NOT WASH THE
APPLIANCE, MAINS
CORD AND PLUG
UNDER RUNNING
WATER AND DO
NOT IMMERSE IT
IN WATER OR ANY
OTHER LIQUID.
DISASSEMBLING YOUR JUICER
Before disassembling, make sure that the
juicer is fully stopped and the power cord is
unplugged from the mains.
1. Store the pulp container and the juice jug
aside.
2. Turn the feed tube anticlockwise until
the arrow on the chamber is aligned with
the open lock mark. Carefully lift the feed
tube. Take care as it may contain raw
material residues.
3. Move the chamber with the screw and
the strainer installed in asink or other
place suitable for cleaning.
4. Turn and pull the press screw upward to
remove it.
5. Then remove the strainer.
6. Clean strainer, press screw and juicing
chamber according to the instructions
below.
NOTE
If you processed raw materials rich
in pulp, the press screw may be
dicult to remove. This is normal. Use
reasonable force to remove it.
CLEANING STRAINERS, PRESS SCREW
AND FEED TUBE
Immediately after disassembling, wash used
strainer, press screw, feed tube and pusher
under running warm water.
Wash in warm water with asmall amount of
washing-up liquid as needed. Rinse and wipe
dry.
If the strainer is contaminated with raw
material residues, remove them with the
supplied brush. We recommend to clean the
strainer with the brush under running water.
If the strainer is heavily contaminated
or contains dried raw material residues,
we recommend to immerse it in warm
water with 10% of lemon juice for about
10minutes. If the strainer holes were
clogged, the juicing yield would be reduced.
NOTE
Strainers, press screw, feed tube,
pusher, juice jug and pulp container
are suitable for dishwashers (in upper
basket).