Catler MG 800 User manual

MG 800
Instructions for use
MEAT GRINDER

MEAT GRINDER

3
TABLE OF CONTENTS
TABLE OF CONTENTS
5 Catler recommends safety rst
8 Know your meat grinder MG 800
10 Operating your meat grinder MG 800
10 Before rst use
10 Assembling the meat grinder
11 Using the meat grinder
11 Kubbe preparation
12 Sausage preparation
13 Speed selection
13 Overheat protection
14 Care and cleaning
14 Disassembling of the meat grinder
14 Cleaning accessories
14 Cleaning the grinder
15 Storage

4CONGRATULATIONS
Congratulations
for purchasing your new meat grinder MG 800.

5
CATLER RECOMMENDS SAFETY FIRST
CATLER RECOMMENDS SAFETY FIRST
We understand the importance of safety and so from the initial design concept to production
itself we focus primarily on your safety. Nevertheless, we ask that you please be careful and
follow the following instructions when using electrical appliances:
IMPORTANT SAFETY INSTRUCTIONS FOR
USING YOUR MG 800 MEAT GRINDER
• This appliance must not be used by children.
Keep the appliance and its power cord out of
reach of children.
• This appliance may be used by persons with
physical, sensory, or mental impairments or
lack of inexperience and knowledge only if they
are properly supervised or have been informed
about how to use of the product in asafe
manner and understand the potential dangers.
• Children must not play with the appliance.
• If the power cord is damaged, have it replaced
in aprofessional service centre in order to
prevent adangerous situation. It is forbidden
to use the appliance with the power cord
damaged.
• Misuse may cause injury.
• Be careful when manipulating with the grinder
knife. Blades of the grinder knife are very sharp
and there is arisk of aserious injury.

6CATLER RECOMMENDS SAFETY FIRST
• The parts of the appliance and the accessories
that get in contact with food, clean according
to the instructions provided in this manual.
• Always unplug the appliance from the power
outlet if you leave it unattended and before
assembling, disassembling, or cleaning.
• Switch the appliance off and unplug it from
the power supply before changing the
accessories or accessible parts that move when
in operation. Always wait till the accessories
or rotating parts completely have stopped.
Use the appliance only with the supplied
accessories.
• Use the appliance according to the instructions provided in this user´smanual. Otherwise,
there is arisk of injury.
• This appliance is designed for household use only. The appliance is not designed for
commercial use. Do not use this appliance in moving vehicles or on boats, outdoors, or for
any purpose other than intended. Otherwise, there is arisk of personal injury.
• Before rst use, make sure that the voltage in your power socket matches the nameplate
voltage on the unit bottom. In case of any doubt, please contact aqualied electrician.
• Put the appliance on astable, heat-resistant, at and dry surface away from the
countertop edge.
• Avoid placing the appliance on or in the vicinity of heat sources, such as hot plates, ovens
or gas burners. Vibrations during operation may cause the appliance to move.
• Do not use this appliance with aprogrammable switch, timer switch or any other device
that automatically switches the appliance on.
• Before turning the appliance on, check that it is correctly assembled. Ensure the screw ring
is correctly tightened.
• Do not attempt to grind bones, nut shells or other hard ingredients.
• Do not leave the appliance in continuous operation under aheavy load for aperiod longer
than 5 minutes. Before turning it on again, allow it to cool down for at least 10 minutes.
• Never use your ngers or other objects to push food through the feed chute. Always use
the supplied pusher.
• If food gets stuck inside the grinding chamber, use the REV button for areverse move of
the worm shaft to remove the stuck food.
• Never run the appliance empty. There is arisk of damage.

7
CATLER RECOMMENDS SAFETY FIRST
• Always switch the appliance o and unplug it from the power supply once food
processing has been completed.
• To prevent potential electric shock, do not submerge this appliance, its base or power
cord in water or any other liquid.
• Regularly check the appliance status. Never use adamaged appliance or appliance with
adamaged accessory, power cord or plug.
• Do not disconnect the appliance from the power socket by pulling the power cord. This
could damage the power cord or the power socket. Disconnect the cord from the power
socket by gently pulling the plug of the power cord.
IMPORTANT SAFETY INSTRUCTIONS FOR USING ELECTRICAL EQUIPMENT
• Fully unwind the power cord before use.
• Do not leave the power cord hanging over the edge of atable or countertop or allow it
to touch ahot surface or to become tangled up. Do not put heavy objects on the power
cord.
• For safety reasons, we recommend connecting the appliance in an independent electrical
circuit separated from other appliances. Do not use adapter plugs or extension cords to
connect the appliance to apower outlet.
• We recommend that you inspect the appliance regularly. Do not use the appliance if it is
damaged in any way or if the power cord or plug are defective. All repairs or adjustments
must be performed at the nearest Catler authorised service centre.
• Any maintenance other than standard cleaning must be performed at authorised Catler
service centre.
• We recommend installing aresidual current device (standard safety switches in your
power outlet) to provide ahigher level of protection when using the appliance. We
recommend installing aresidual current device (with anominal residual operating current
of no more than 30 mA) in the electric circuit in which your appliance is to be connected.
For further expert advice, please contact your electrician.
The user’smanual is also available at www.catler.eu.
FOR HOUSEHOLD USE ONLY.

8KNOW YOUR MEAT GRINDER MG 800
KNOW YOUR MEAT GRINDER MG 800
1
5
2
3
4
7
8
9
10
12
6
11
16
15
18
14
17
19
13

9
KNOW YOUR MEAT GRINDER MG 800
1. Food tray
2. Feed chute
3. Fixing ring
4. Grinding attachment
5. Locking handle for attaching the grinding attachment
6. Display
7. Ventilation vents
8. button (turn on/o)
9. button – speed setting (low or high)
10. REV button (reverse function)
11. Motor unit
12. Feed with suction cups – provide better stability when operating the meat grinder
13. Grinding discs
14. Sausage attachment
15. Food pusher
16. Worm shaft
17. Kubbe attachment
18. Cover
19. Grinding knife

10 OPERATING YOUR MEAT GRINDER MG 800
OPERATING YOUR MEAT GRINDER MG 800
BEFORE FIRST USE
Before rst use, remove all packaging
and advertising labels / stickers from the
appliance. Make sure you have removed all
accessories from the package. Check the
appliance or any accessory are not damaged.
Wipe the outer surface of the motor unit with
asoft sponge slightly moistened in warm
water with alittle washing-up liquid. Wipe
dry using aclean wiping cloth.
Other accessories wash in warm water with
alittle washing-up liquid. Rinse with clean
water and wipe dry.
Before assembling the grinder ensure all
parts are completely dry.
ASSEMBLING THE MEAT GRINDER
1. Place the grinder on adry, at, and solid
surface.
2. Push slightly the locking handle
clockwise till it points the open lock
symbol and keep it in this position.
3. Insert the grinding attachment vertically
into the inlet hole in the grinder.
4. Push the locking handle clockwise until it
is locked.
5. Insert the worm shaft into the grinding
chamber. If necessary, turn the warm
shaft to t easier into the axis of the
motor unit.
6. Install the grinding knife to the worm
shaft. It is important the blades are
oriented out of the grinding chamber. If
the grinding knife is placed properly, the
grinder will not grind meat.
7. Attach one of the grinding discs on the
grinding knife. Select agrinding disc
depending on the preferred grinding
roughness and intended meat use. Make
sure that the tab in the grinding chambre
is engaged with the notch in the grinding
disc.
WARNING!
WHEN
ATTACHING THE
GRINDING KNIFE, BE
VERY CAREFUL NOT
TO GET INJURED
WITH ITS EDGE.
8. Now attach the screw cap and screw
it properly by turning clockwise. Now
attach the xing ring and screw it
properly by turning clockwise. Ensure the
xing ring is rmly tightened. However,
do not use excessive force not to damage
the thread.
9. Place the food tray on the feed chute
and insert the food pusher into the feed
chute.
The grinder is now ready to use.