Cattron EliteIQ User manual

Quick Start Guide
EliteIQ™
1. Wire Your EliteIQ
The EliteIQ consists of the main processing unit enclosure and the cellular modem enclosure. The power
and data cables between them will need connected as well as any required I/O connections to be
monitored.
1. Drill holes in the main processing unit enclosure for the amount of I/O wiring required, affix the
necessary conduit fittings, and assure proper waterproofing. Feed the following wires from the modem
enclosure through as well.
2. Attach the DB9 (M) to RJ45 (F) adapter, #1800-0082, to J16 on the back of the main processing unit
swing panel.
3. Connect RJ45/Ethernet cable, #1800-0083, to the DB9/RJ45 adapter.
Configuration Sheets and Manuals Are Available at Cattron.com
Nimble: 9M01-920X-A001 | August 2022
Recommended
Drill Area
1.
2. 3.
Bottom

Quick Start Guide
EliteIQ™
1. Wire Your EliteIQ
4. Insert the other end of the RJ45/Ethernet cable through the cable gland on the cellular modem
enclosure and connect the cable into the other DB9/RJ45 adapter installed on the cellular modem.
5. Connect cable #1800-0023 to the circular 4 pin connector on the modem enclosure.
6. The other end of #1800-0023 has 4 leads. Use the screw terminals on the J12 connector to connect
the brown wire to pin 1/V+ and the black wire to pin 2/GND. Ground the white and blue wires to the
main panel ground stud. Strip back the cable jacket as needed.
Configuration Sheets and Manuals Are Available at Cattron.com
Nimble: 9M01-920X-A001 | August 2022
4.
5. 6.

Quick Start Guide
EliteIQ™
1. Wire Your EliteIQ
7. Connect the #1300-0020 coax cable N-male connector to the N-female connector on the modem
enclosure. Connect the other N-male connector of the cable to the #1300-0027 antenna and mount the
antenna as high as possible and away from metal structures (poles, buildings, fences, etc.) and away
from any RF generating types of equipment (AC switching circuits, VFDs, other radios, etc.).
8. Attach the black wire from the +12V BATTERY connector to the negative battery post.
9. Wire AC power to the Line (Black), Ground (Green), and Neutral (White) terminals on the main unit
panel.
Configuration Sheets and Manuals Are Available at Cattron.com
Nimble: 9M01-920X-A001 | August 2022
7.
8. 9.

Quick Start Guide
EliteIQ™
2. Power On Your EliteIQ
1. The main power switch for the EliteIQ is labeled
SW2 and is on the back of the swing panel in the
main enclosure.
2. If you purchased a data plan with the hardware,
your device arrives activated and ready to use. If
you have the hardware and need to activate
service, please contact [e-mail]
or call 877.399.2937.
Configuration Sheets and Manuals Are Available at Cattron.com
Nimble: 9M01-920X-A001 | August 2022
3. Access RemoteIQ
•To access the RemoteIQ™cloud-based monitoring service, navigate to
https://antx.trihedral.com/(sitename), site name being your company name. Log in with the credentials that
you provided us, or contact customer service if you need to create credentials.
•If your system is preconfigured, the I/O will arrive programmed per the configuration sheet you provided to
us. If it is not preconfigured or if changes are required, the EliteIQ can be programmed via a locally
connected PC, or remotely over the cellular network. Programming instructions can be found in the
manual. If you need configuration assistance, email [e-mail] or call 877.399.2937.
4. Access Device Identification
Using a QR Code scanning app, scan the QR codes on
the EliteIQ device to access device identification
information such as IMEI, SIM, IP, and Serial Numbers

Quick Start Guide
EliteIQ™
EliteIQ depicted without customer I/O. For detailed information, reference the schematic drawings and
online manual found at https://www.cattron.com/support/user-manuals/water-and-wastewater-user-
manuals/.
Configuration Sheets and Manuals Are Available at Cattron.com
Nimble: 9M01-920X-A001 | August 2022
Wired EliteIQ